Table of Contents
Advertisement
42
Changing the maintenance program
41.2.3
Configuration
After connecting one or multiple membrane dosing pumps, correct
After connecting one or multiple membrane dosing pumps, correct
triggering has to be activated and configured in PoolManager
and configured in PoolManager
You'll find all relevant setting in the menu
Service functions
Selecting the pump type Membrane pump will activate the triggering of
individual dosing strokes via PoolManager
The default setting for pump type is Standard.
intended for conventional peristaltic pumps.
Menu Configuration dosage pumps
Pump type
For membrane pumps, select
For membrane pumps, select Membrane pump.
pH / mV (Cl) / Cl
Max. no. of strokes
Enter the desired maximum number of strokes
Enter the desired maximum number of strokes
pH / mV (Cl) / Cl
[strokes/min] at a dosing output of 100%.
[strokes/min] at a dosing output of 100%.
For more information, also review the section
For more information, also review the section
Determining output
Pump rate
Enter the correct maximum dosing output for the
Enter the correct maximum dosing output for the
pH / mV (Cl) / Cl
corresponding dosing pump in [l/h]
(for the maximum number of strokes entered)
(for the maximum number of strokes
IMPORTANT NOTICE!
Incorrect configuration of dosing output
Incorrect configuration of dosing output
If a pump's dosing output is not configured correctly,
If a pump's dosing output is not configured correctly,
then the following problems will arise:
then the following problems will arise:
• The calculation for duration of manual dosing is not
The calculation for duration of manual dosing is not
correct.
• The configuration assistant
parameters calculates erroneous settings.
parameters calculates erroneous settings.
INFO
Membrane dosage pump for O2 (BayroSoft)
Membrane dosage pump for O2 (BayroSoft)
For
For
O2
O2
dosing
dosing
Membrane pump cannot be selected. For BayroSoft
dosing, however, a membrane pump can be triggered
dosing, however, a membrane pump can be triggered
with simple turning on and off, like a peristaltic pump.
with simple turning on and off, like a peristaltic pump.
The output desired can be configured directly on the
The output desired can be configured directly on the
pump.
This variation is sufficient, as PoolManager
This variation is sufficient, as PoolManager
doses either 100% or not at all. Therefore, variable
doses either 100% or not at all. Therefore, variable
triggering of individual pump stro
triggering of individual pump strokes is not necessary.
41.2.3.1 Determining output
The maximum number of strokes per minutes must be configured such
The maximum number of strokes per minutes must be configured such
that the desired maximum output in l/h is yielded at 100% dosing
that the desired maximum output in l/h is yielded at 100% dosing
output.
Output can be determined for certain stroke rates with the data sheet
Output can be determined for certain stroke rates with the data sheet
for the pump being used, such as for 60 strokes/min, 120 strokes/min,
the pump being used, such as for 60 strokes/min, 120 strokes/min,
or 180 strokes for min.
For many pumps, stroke length can also be configured using a
For many pumps, stroke length can also be configured using a
controller on the pump. This also makes it possible to adjust the
controller on the pump. This also makes it possible to adjust the
pump's output to match needs.
Example:
A maximum pump output of 2.0 l/h is planned for a system. The
A maximum pump output of 2.0 l/h is planned for a system. The
maximum stroke frequency on the pump is 180 strokes/min.
maximum stroke frequency on the pump is 180 strokes/min.
Using the pump's data sheet, the desired output of 2.0 l/h is yielded
Using the pump's data sheet, the desired output of 2.0 l/h is yielded
with maximum stroke length (100%) and a stroke frequency of 40%,
with maximum stroke length (100%) and a stroke frequency of 40%,
i.e. 72 stokes/min.
Therefore, the maximum number of strokes must be set to 72/min in
Therefore, the maximum number of strokes must be set to 72/min in
®
PoolManager
in this case. Then PoolManager
in this case. Then PoolManager
dosing pulses per minuted at maximum dosing output (100%). This will
dosing pulses per minuted at maximum dosing output (100%). This will
lead to the desired maximum dosing output of 2.0 l/h.
®
menu.
Configuration dosing pumps
Configuration dosing
will activate the triggering of
®
.
This operating mode is
dosing pump in [l/h]
for configuring control
(BayroSoft),
(BayroSoft),
the
the
pump
pump
cannot be selected. For BayroSoft
®
always
®
will generate 72
of 2.0 l/h.
User Manual PoolManager
42
Changing the maintenance program
Changing the maintenance program
The maintenance program (oxygen (02 / BayroSoft) / Chlorine (Cl) /
The maintenance program (oxygen (02 / BayroSoft) / Chlorine (Cl) /
Bromine (Br)) is changed in the menu
Bromine (Br)) is changed in the menu
Menu hotkey
Service functions
Enhanced functions
Configuration care method
The new program that is desired and a matching code number has to
The new program that is desired and a matching code number has to
be entered for each. The code number depends on the previous
be entered for each. The code number depends on the previous
maintenance program and on the new maintenance program selected:
Current program
PoolManager
®
PoolManager
®
PoolManager
®
PoolManager
®
PoolManager
®
PoolManager
®
type
type
®
care method
on the new maintenance program selected:
New program
New program
O2
PoolManager
PoolManager
®
Cl
O2
PoolManager
PoolManager
®
Br
Cl
PoolManager
PoolManager
®
O2
Cl
PoolManager
PoolManager
®
Br
Br
PoolManager
PoolManager
®
O2
Br
PoolManager
PoolManager
®
Cl
Code number
122
123
221
223
321
322
77
Advertisement
Table of Contents
