Table of Contents
Advertisement
13
Automatic dosage O2 (BayroSoft)
13.3
O2 (BayroSoft) menu
The menu
O2 (BayroSoft) contains the following sub
Configuration O2 (BayroSoft)
Configuration of all relevant parameters for automatic O2 dosage
Configuration of all relevant parameters for automatic O2 dosage
Average temperature value
Display of average temperature value measured for the entire week
Display of average temperature value measured for the entire week
and for the individual 1/3 weeks
Date & time
Here, correct configuration of the current weekday, date, and time can
be checked and corrected as needed.
Supplemental dosages
In this menu, supplemental dosages can be configured; see section
In this menu, supplemental dosages can be configured; see section
Supplemental dosages.
Operating hours
In this menu, the permissible times for BayroSoft dosing can be
In this menu, the permissible times for BayroSoft dosing can be
restricted. This can be used when, for example, it is preferred there be
stricted. This can be used when, for example, it is preferred there be
no dosages during night-time hours.
The menu
Planned dosing (also accessible via the menu
O2 (BayroSoft)) contains the following information:
contains the following information:
Display of the next planned dosages with date and time. The main
•
dosage and the two refresh dosages are displayed.
dosage and the two refresh dosages are displayed.
When needed, dosage planning can be reset in this menu.
When needed, dosage planning can be reset in this menu.
In this case, the current plan is discarded and an entirely new plan is
In this case, the current plan is discarded and an entirely new plan is
performed, starting from the current weekday and time
performed, starting from the current weekday and time.
Note: Supplemental dosages are NOT displayed.
Note: Supplemental dosages are NOT displayed.
13.4
Configuration O2 (BayroSoft)
The following settings can be configured:
Parameter
Setting range
Temp. compensation
Off / normal / high
Temperature compensation
Temperature compensation should be set to "high" if
the BayroSoft refresh dosages prove to be too low.
the BayroSoft refresh dosages prove to be too low.
Hose config. O2
0.9 l/h / 3 l/h / ...
Pool volume
1...5000m³
When entering the pool volume, the BayroSoft dose
When entering the pool volume, the BayroSoft dose
amount is automatically adjusted to match the pool
amount is automatically adjusted to match the pool
size (0.5 litre per 10m³ of pool volume).
size (0.5 litre per 10m³ of pool volume).
contains the following sub-menus.
weekday, date, and time can
(also accessible via the menu
date and time. The main
Standard setting
Standard setting
Default set Europe
Default set Europe
Normal
Normal
3 l/h
3 l/h
Here, the BayroSoft pump dosing
Here, the BayroSoft pump dosing
output is entered. This setting
output is entered. This setting
absolutely must coincide with the
absolutely must coincide with the
actual pump output on the
actual pump output on the pump being
used. Otherwise, it's possible that
used. Otherwise, it's possible that
PoolManager
PoolManager
®
does not correctly
calculate the requisite pump time for a
calculate the requisite pump time for a
dosage, and that the BayroSoft dose
dosage, and that the BayroSoft dose
amounts are not correct!
amounts are not correct!
The dosing output for the standard
The dosing output for the standard
BayroSoft dosage
BayroSoft dosage pump is 3.0 l/h.
40m³
40m³
User Manual PoolManager
O2 dose amount
0.0...99.9 l
Here, the basic dose amount is indicated for
Here, the basic dose amount is indicated for
automatic O2 dosage.
automatic O2 dosage.
The standard value inferred from the pool volume
The standard value inferred from the pool volume
can be adjusted again. The actual main dose
can be adjusted again. The actual main dose
amount and the two refresh dosages depend on the
amount and the two refresh dosages depend on the
average water temperature measure
average water temperature measured.
O2 dosage day
Monday ... Sunday
Monday ... Sunday
Weekday for main dosage.
Weekday for main dosage.
6s dosage
Active / inactive
Active / inactive
After turning on PoolManager
After turning on PoolManager
after 12 hours of operation, the BayroSoft pump is
after 12 hours of operation, the BayroSoft pump is
briefly started for ca. 6s in order to hinder product
briefly started for ca. 6s in order to hinder product
sedimentation.
sedimentation.
13.5
Supplemental dosages
Supplemental dosages
PoolManager
®
provides the option of programming further
provides the option of programming further
supplemental dosages in addition to auto mode with temperature
supplemental dosages in addition to auto mode with temperature
compensation.
The temperature dosages are then performed in supplement to the
The temperature dosages are then performed in supplement to the
main dosage and to the refresh dosages. The supplemental dose
main dosage and to the refresh dosages. The supplemental dose
amount is fixed, programmed figure and is not
fixed, programmed figure and is not compensated.
For supplemental dosages, the following parameters can be
For supplemental dosages, the following parameters can be
configured in the menu "Supplemental dosages":
configured in the menu "Supplemental dosages":
Parameter
Explanation
Weekdays
Here the days of the week on which additional dosing is to
Here the days of the week on which additional dosing is to
take place (one or more) can be selected.
place (one or more) can be selected.
Default: Off
Time
Start time of the additional dosages
Start time of the additional dosages
(the same for every weekday).
(the same for every weekday).
Default: Midnight
Dose amount
Dose amount for supplemental dosages (the same for every
Dose amount for supplemental dosages (the same for every
weekday).
Default: 0.2 l
Example:
The system should be configured such that on Friday 2.5 l of
system should be configured such that on Friday 2.5 l of
BayroSoft is dosed, and 2.0 l each on Monday and Wednesday.
BayroSoft is dosed, and 2.0 l each on Monday and Wednesday.
Temperature compensation is not desired.
Temperature compensation is not desired.
To do so, the following settings are required:
To do so, the following settings are required:
Menu
O2 (BayroSoft)
Sub-menu Configuration O2 (BayroSoft)
Dose amount O2 = 2.5 l
•
Temp. compensation = Off
•
Dosage day O2 = Friday
•
Sub-menu Supplemental dosages:
Supplemental dosages:
•
Weekdays = Monday, Wednesday
Weekdays = Monday, Wednesday
•
Dose amount O2 = 2.0 l
•
If temperature compensation is activated, then the main dosage is
If temperature compensation is activated, then the main dosage is
compensated for temperature and, if applicable, the two refresh
dosages are additionally performed.
dosages are additionally performed.
®
0.5 litre per 10m³ of pool
volume
(e.g. 2.0 l for 40m³ pool
volume)
Friday
Active
and no later than
®
yroSoft)
and, if applicable, the two refresh
40
Advertisement
Table of Contents
