Mains Connection; Pre-Fuses; Motor Connection - Danfoss VLT 6000 HVAC Series Quick Setup Manual

VLT type Tightening-up
3 x 200 - 240 V torque
VLT 6002-6005 0.5-0.6 Nm
VLT 6006-6011 1.8 Nm (IP 20)
VLT 6006-6016 1.8 Nm (IP 54)
VLT 6016-6027 3.0 Nm (IP 20)
VLT 6022-6027 3.0 Nm (IP 54)
VLT 6032 6.0 Nm
VLT 6042-6062 11.3 Nm
VLT type Tightening-up
3 x 380-460 V torque
VLT 6002-6011 0.5-0.6 Nm
VLT 6016-6027 1.8 Nm (IP 20)
VLT 6016-6032 1.8 Nm (IP 54)
VLT 6032-6052 3.0 Nm (IP 20)
VLT 6042-6052 3.0 Nm (IP 54)
VLT 6062-6072 6.0 Nm
VLT 6102-6122 15 Nm (IP 20)
24 Nm (IP 54)
VLT 6152-6352 19 Nm
VLT 6400-6550 42 Nm
VLT type Tightening-up
3 x 525-600 V torque
VLT 6002-6011 0.5-0.6 Nm
VLT 6016-6027 1.8 Nm
VLT 6032-6042 3.0 Nm
VLT 6052-6072 6.0 Nm
VLT 6100-6150 11.3 Nm
VLT 6175-6275 11.3 Nm
1. Loadsharing terminals 14 Nm/M6, 5 mm Allen key
2. IP 54 units with RFI filter line terminals 6 Nm
3. Allen screws (hexagon)
4. Loadsharing terminals 9.5 Nm/M8 (bolt)

Mains connection

Mains must be connected to terminals 91, 92, 93.
Mains voltage 3 x 200-240 V
91, 92, 93 Mains voltage 3 x 380-460 V
L1, L2, L3 Mains voltage 3 x 525-600 V
NB!:
Check that the mains voltage fits the mains
voltage of the frequency converter, which
can be seen from the nameplate.
See Technical data for correct sizing of
cable cross-sections.
12
Screw/bolt Allen
size key
size
M3
M4
M4
3)
M5 4 mm
2) 3)
M5 4 mm
3)
M6 5 mm
M8 (bolt)
Screw/bolt Allen
size key
size
M3
M4
M4
3)
M5 4 mm
2) 3)
M5 4 mm
3)
M6 5 mm
3)
M8 6 mm
1) 3)
8 mm
4)
M10 (bolt)
M12 (bolt)
Screw/bolt Allen
size key
size
M3
M4
2) 3)
M5 4 mm
3)
M6 5 mm
M8
M8
®
VLT

Pre-fuses

See Technical data for correct sizing of pre-fuses.

Motor connection

The motor must be connected to terminals 96,
97, 98. Earth to terminal 94/95/99.
Nos.
96. 97. 98 Motor voltage 0-100 % of mains voltage
U, V, W
No. 94/95/99 Earth connection
See Technical data for correct sizing of
cable cross-sections.
All types of three-phase asynchronous standard
motors can be used with a VLT 6000 HVAC unit.
Small-size motors are normally star-connected.
(220/380 V, /Y). Large-size motors are
delta-connected (380/660 V,
connection and voltage can be read from
the motor nameplate.
NB!:
In older motors without phase coil
insulation, a LC filter should be fitted to
the frequency converter output. See the
Design Guide or contact Danfoss.
MG.60.C7.02 - VLT is a registered Danfoss trademark
6000 HVAC
/Y). The correct