Control Panel And Features - Whirlpool WETLV27HW0 Service Manual

GENERAL INFORMATION

CONTROL PANEL AND FEATURES

STANDARD VENT MODELS
LONG VENT MODELS
Not all features and options are available on all models. Appearance may vary.
Not all features and options are available on all models. Appearance may vary.
WASHER
Washer
1 WASH CYCLE KNOB
Use the Wash Cycle knob to select available cycles on your
1. WASH CYCLE KNOB
washer. Turn the knob to select a cycle for your laundry load.
Use the Wash Cycle knob to select available cycles on your
See "Washer Cycle Guide" for detailed descriptions of cycles.
washer. Turn the knob to select a cycle for your laundry
load. WASH TEMP
2
You may select a Wash Temperature based on the type of
See "Washer Cycle Guide" for detailed descriptions of
fabric and soils being washed. Use the warmest wash water
cycles.
safe for the fabric. Follow garment label instructions.
2. WASH TEMP
FABRIC SOFTENER
3
You may select a Wash Temperature based on the type
Set this knob to Yes when adding fabric softener to the
of fabric and soils being washed. Use the warmest
fabric softener dispenser.
wash water safe for the fabric. Follow garment label
START/PAUSE
4 instructions.
Press the START/PAUSE button to start the washer.
3. FABRIC SOFTENER
5 WASH STATUS INDICATOR LIGHTS
Set this knob to Yes when adding fabric softener to the
fabric softener dispenser.
4. WASHER START/PAUSE
Press the START/PAUSE button to start the washer.
The Cycle Status lights show the progress of a cycle.
5. WASH STATUS INDICATOR LIGHTS
At each stage of the process, you may notice sounds
or pauses that are different from your previous washer.
SENSE FILL
When the Start/Pause button is pressed, the washer will ll
and begin sensing to determine load size and balance.
Once sensing is complete, the washer will ll to the
The Cycle Status lights show the progress of a cycle. At
appropriate level for the detected load size and then begin
each stage of the process, you may notice sounds or
the wash phase of the cycle.
pauses that are different from your previous washer.
NOTE: Sensing and wash phases will be paused by opening
the unlocked lid. Close the lid to resume the cycle. If the lid
is left open for more than 10 minutes, the washer will cancel
the cycle and pump out the water. The lid will lock after the
wash phase to begin the initial spinout and remain locked
1-4 27" Stacked Laundry Center
n
for the remainder of the cycle.
Control Panel and Features
1
4
5
1
4
5
1
5 4
4
5
Not all features and options are available on all models. Appearance may vary.
2 3
2
2 3
WASH
SENSE/FILL
WASH
When the Start/Pause button is pressed, the washer The washer will ll to the correct water level based
The washer will ll to the correct water level based on the load
will fill and begin sensing to determine load size and
size. Certain cycles may agitate during the ll process to boost
size. Certain cycles may agitate during the ll proce
cleaning. You will hear the agitator rotate, followed by a pause
balance. Once sensing is complete, the washer will fill to
cleaning. You will hear the agitator rotate, followed
lasting several seconds. When the wash cycle begins, you will
the appropriate level for the detected load size and then
hear the agitator increase speed. The motor sounds may change
lasting several seconds. When the wash cycle begi
begin the wash phase of the cycle.
at different stages in the wash cycle while the washer performs
hear the agitator increase speed. The motor sounds
NOTE: Sensing and wash phases will be paused by
different wash actions.
opening the unlocked lid. Close the lid to resume the
at different stages in the wash cycle while the wash
RINSE
cycle. If the lid is left open for more than 10 minutes, the
different wash actions.
Certain cycles use a spray rinse, which adds water to the tub
washer will cancel the cycle and pump out the water.
while the basket spins. You may hear the motor turning on brie y
The lid will lock after the wash phase to begin the initial
RINSE
(short hum) to move the basket while lling.
spinout and remain locked for the remainder of the cycle.
Certain cycles use a spray rinse, which adds water
DRAIN/SPIN
WASH
The washer spins the load at increasing speeds for proper water
while the basket spins. You may hear the motor turn
The washer will fill to the correct water level based on
removal, based on the selected cycle.
(short hum) to move the basket while lling.
the load size. Certain cycles may agitate during the fill
DONE
process to boost cleaning. You will hear the agitator
DRAIN/SPIN
Once the cycle is complete, this light will come on. Remove the
rotate, followed by a pause lasting several seconds. When
load promptly for best results.
The washer spins the load at increasing speeds for
the wash cycle begins, you will hear the agitator increase
LID LOCK
removal, based on the selected cycle.
speed. The motor sounds may change at different stages
The Lid Lock feature allows for
in the wash cycle while the washer performs different
higher spin speeds. When the Lid
DONE
wash actions.
Lock light is lit, the lid is locked and
Once the cycle is complete, this light will come on.
RINSE
cannot be opened without pausing
load promptly for best results.
the cycle. When the light is off, the
Certain cycles use a spray rinse, which adds water to
lid can be opened.
the tub while the basket spins. You may hear the motor
LID LOCK
To open the lid after it has been
turning on briefly (short hum) to move the basket while
The Lid Lock feature allows for
locked, press START/PAUSE.
filling.
The lid will unlock once the
higher spin speeds. When the Lid
DRAIN/SPIN
washer movement has stopped.
Lock light is lit, the lid is locked and
The washer spins the load at increasing speeds for proper
This may take several minutes if
water removal, based on the selected cycle. cannot be opened without pausing
the load was spinning at high speed.
Press START/PAUSE again to resume the cycle.
the cycle. When the light is off, the
lid can be opened.
To open the lid after it has been
locked, press START/PAUSE.
6
3
6
6
7
7
7