Automatic Test Mode; Manual Test Mode; Calibration Mode; Ui Test Mode - Whirlpool WETLV27HW0 Service Manual

To access Automatic Test Mode, perform steps
To access Automatic Test Mode, perform steps
AUTOMATIC TEST MODE (Page 8)
1 and 2 of Activating the Service Diagnostic
1 and 2 of Activating the Service Diagnostic FOR SERVICE TECHNICIAN'S USE ONLY
Test Modes. Turn the cycle selector knob until
To access Automatic Test Mode, perform steps
Test Modes. Turn the cycle selector knob until
DIAGNOSTICS & TROUBLESHOOTING
the status LEDs correspond as follows:
1 and 2 of Activating the Service Diagnostic
the status LEDs correspond as follows:
AUTOMATIC TEST MODE (Page 8) Test Modes. Turn the cycle selector knob until
"Drain/Spin" LED On
"Drain/Spin" LED On
the status LEDs correspond as follows:
To access Automatic Test Mode, perform steps
Automatic Test Mode (Page 2-10)
Sense Wash
1 and 2 of Activating the Service Diagnostic
"Drain/Spin" LED On
Sense Wash
Fill
Fill
To access Automatic Test Mode, perform steps 1 and 2 of
Test Modes. Turn the cycle selector knob until
NOTE: Status LED names may vary between
Activating the Service Diagnostic Test Modes. Turn the cycle NOTE: Status LED names may vary between
the status LEDs correspond as follows:
Sense Wash Rinse
selector knob until the status LEDs correspond as follows:
makes and models.
makes and models.
Fill
n "Drain/Spin" LED On
"Drain/Spin" LED On
NOTE: Status LED names may vary between
Press the START button to begin the automatic
Press the START button to begin the automatic
makes and models.
test. See page 8 for order of automatic test.
test. See page 8 for order of automatic test.
Sense Wash Rinse
Press the START button to begin the automatic
Upon entering the automatic test mode, the
Upon entering the automatic test mode, the
Fill
test. See page 8 for order of automatic test.
washer will perform an automatic test with
washer will perform an automatic test with
NOTE: Status LED names may vary between
NOTE: Status LED names may vary between makes and
water cycles to check major washer functions.
Upon entering the automatic test mode, the
water cycles to check major washer functions.
makes and models.
models.
washer will perform an automatic test with
Pressing the START button will manually
Press the START button to begin the automatic
Pressing the START button will manually
Press the START button to begin the automatic test. See page
water cycles to check major washer functions.
advance to the next step.
test. See page 8 for order of automatic test. 2-10 for order of automatic test.
advance to the next step.
Pressing the START button will manually
n Upon entering the automatic test mode, the washer will
Upon entering the automatic test mode, the
Press and hold the START button for 3 seconds
Press and hold the START button for 3 seconds
perform an automatic test with water cycles to check major
advance to the next step.
washer will perform an automatic test with
at any time to exit Automatic Test mode.
at any time to exit Automatic Test mode.
washer functions.
water cycles to check major washer functions.
Press and hold the START button for 3 seconds
IMPORTANT: Lid must be closed with lid lock
IMPORTANT: Lid must be closed with lid lock
n Pressing the START button will manually advance to the
next step. at any time to exit Automatic Test mode.
enabled to perform test.
Pressing the START button will manually
enabled to perform test.
n Press and hold the START button for 3 seconds at any time
IMPORTANT: Lid must be closed with lid lock advance to the next step.
to exit Automatic Test mode.
MANUAL TEST MODE (Page 9)
MANUAL TEST MODE (Page 9)
enabled to perform test.
Press and hold the START button for 3 seconds
IMPORTANT: Lid must be closed with lid lock enabled to
at any time to exit Automatic Test mode. To access Manual Test Mode, perform steps
perform test. To access Manual Test Mode, perform steps
MANUAL TEST MODE (Page 9)
1 and 2 of Activating the Service Diagnostic
1 and 2 of Activating the Service Diagnostic
IMPORTANT: Lid must be closed with lid lock
Test Modes. Turn the cycle selector knob
To access Manual Test Mode, perform steps
Test Modes. Turn the cycle selector knob
enabled to perform test.
Manual Test Mode (Page 2-11)
until the status LEDs correspond as follows:
1 and 2 of Activating the Service Diagnostic
until the status LEDs correspond as follows:
To access Manual Test Mode, perform steps 1 and 2 of
MANUAL TEST MODE (Page 9) Test Modes. Turn the cycle selector knob
Activating the Service Diagnostic Test Modes. Turn the cycle "Drain/Spin" & "Done" LEDs On
"Drain/Spin" & "Done" LEDs On
until the status LEDs correspond as follows:
selector knob until the status LEDs correspond as follows:
To access Manual Test Mode, perform steps
n "Drain/Spin" & "Done" LEDs On
1 and 2 of Activating the Service Diagnostic
"Drain/Spin" & "Done" LEDs On Sense Wash
Sense Wash
Fill
Fill
Test Modes. Turn the cycle selector knob
Press the START button to enter Manual Test
Press the START button to enter Manual Test
until the status LEDs correspond as follows:
Sense Wash Rinse
Mode. See page 9 for manual test mode.
Mode. See page 9 for manual test mode.
Fill
"Drain/Spin" & "Done" LEDs On
Press the START button to enter Manual Test
Upon entering the manual test mode,
Upon entering the manual test mode,
n Press the START button to enter Manual Test Mode. See
Mode. See page 9 for manual test mode.
the washer will have all outputs OFF.
page 2-11 for manual test mode.
the washer will have all outputs OFF.
Sense Wash Rinse
n Upon entering the manual test mode, the washer will have Upon entering the manual test mode,
The cycle selector knob is used to select
The cycle selector knob is used to select
Fill
all outputs OFF.
the washer will have all outputs OFF.
the output to be tested.
Press the START button to enter Manual Test
the output to be tested.
n The cycle selector knob is used to select the output to be
Mode. See page 9 for manual test mode. The cycle selector knob is used to select
tested.
The Start button will activate/deactivate
The Start button will activate/deactivate
the output to be tested.
Upon entering the manual test mode,
n The Start button will activate/deactivate the selected
the selected output.
the selected output.
output.
the washer will have all outputs OFF.
The Start button will activate/deactivate
When the selected output is activated, the
When the selected output is activated, the
n When the selected output is activated, the corresponding
the selected output.
The cycle selector knob is used to select
corresponding status LEDs flash ON & OFF.
corresponding status LEDs flash ON & OFF.
status LEDs flash ON & OFF.
the output to be tested.
When the selected output is activated, the
n Press and hold the START button for 3 seconds at any time
Press and hold the START button for 3
Press and hold the START button for 3
to exit Manual test mode.
corresponding status LEDs flash ON & OFF.
The Start button will activate/deactivate
seconds at any time to exit Manual test mode.
seconds at any time to exit Manual test mode.
IMPORTANT: As a safety feature, the lid must be closed with
the selected output.
Press and hold the START button for 3
IMPORTANT: As a safety feature, the lid
lid lock enabled to activate either Agitate or Spin Test. IMPORTANT: As a safety feature, the lid
seconds at any time to exit Manual test mode.
When the selected output is activated, the
must be closed with lid lock enabled to
NOTE: Multiple outputs may be activated simultaneously.
must be closed with lid lock enabled to
corresponding status LEDs flash ON & OFF.
activate either Agitate or Spin Test.
IMPORTANT: As a safety feature, the lid
NOTE: Outputs left on will time-out after 5 minutes. activate either Agitate or Spin Test.
must be closed with lid lock enabled to
Press and hold the START button for 3 NOTE: Multiple outputs may be activated
NOTE: Multiple outputs may be activated
activate either Agitate or Spin Test.
seconds at any time to exit Manual test mode. simultaneously.
simultaneously.
NOTE: Multiple outputs may be activated
NOTE: Outputs left on will time-out after 5 minutes.
IMPORTANT: As a safety feature, the lid
NOTE: Outputs left on will time-out after 5 minutes.
simultaneously.
must be closed with lid lock enabled to
activate either Agitate or Spin Test. NOTE: Outputs left on will time-out after 5 minutes.
NOTE: Multiple outputs may be activated
simultaneously.
2-4 27" Stacked Laundry Center
n
NOTE: Outputs left on will time-out after 5 minutes.
For Service Technician Use Only
Rinse Drain Done
Rinse Drain Done
Spin
Spin
Drain Done
Spin
Drain Done
Spin
Rinse Drain Done
Rinse Drain Done
Spin
Spin
Drain Done
Spin
Drain Done
Spin

CALIBRATION MODE

NOTE: Calibration only applies to models
NOTE: Calibration only applies to models
CALIBRATION MODE
that do not have level selection.
that do not have level selection.
IMPORTANT: Calibration must be performed
NOTE: Calibration only applies to models
IMPORTANT: Calibration must be performed
when any of the following components have
that do not have level selection.
when any of the following components have
been replaced: Main Control, Basket, Drive
been replaced: Main Control, Basket, Drive
IMPORTANT: Calibration must be performed
CALIBRATION MODE
Assembly, Suspension, Motor, and Capacitor.
Assembly, Suspension, Motor, and Capacitor.
when any of the following components have
NOTE: Calibration only applies to models
Not performing calibration will result in poor
Not performing calibration will result in poor
been replaced: Main Control, Basket, Drive Calibration Mode
that do not have level selection.
wash performance.
wash performance.
Assembly, Suspension, Motor, and Capacitor.
NOTE: Calibration only applies to models that do not have
IMPORTANT: Calibration must be performed
Not performing calibration will result in poor
Do NOT interrupt calibration, disturb washer,
Do NOT interrupt calibration, disturb washer,
level selection.
when any of the following components have
wash performance.
or remove power; otherwise, calibration
or remove power; otherwise, calibration
IMPORTANT: Calibration must be performed when any of
been replaced: Main Control, Basket, Drive
must be repeated.
must be repeated.
Do NOT interrupt calibration, disturb washer,
the following components have been replaced: Main Control,
Assembly, Suspension, Motor, and Capacitor.
Basket, Drive Assembly, Suspension, Motor, and Capacitor. Not
or remove power; otherwise, calibration
Lid must be down to perform test.
Lid must be down to perform test.
Not performing calibration will result in poor
performing calibration will result in poor wash performance.
must be repeated.
Basket must be empty to perform test
wash performance.
Basket must be empty to perform test
n Do NOT interrupt calibration, disturb washer, or remove
Lid must be down to perform test.
(no water or clothes).
(no water or clothes).
power; otherwise, calibration must be repeated.
Do NOT interrupt calibration, disturb washer,
Basket must be empty to perform test
Calibration cycle runs for approximately
n Lid must be down to perform test.
or remove power; otherwise, calibration Calibration cycle runs for approximately
(no water or clothes).
2–4 minutes. * Cycle completes when lid
2–4 minutes. * Cycle completes when lid
must be repeated.
n Basket must be empty to perform test (no water or
unlocks and washer enters standby mode.
clothes).
unlocks and washer enters standby mode.
Calibration cycle runs for approximately
Lid must be down to perform test.
n Calibration cycle runs for approximately 2–4 minutes.*
2–4 minutes. * Cycle completes when lid
*If Calibration Mode is run on a washer
*If Calibration Mode is run on a washer
Basket must be empty to perform test
Cycle completes when lid unlocks and washer enters
unlocks and washer enters standby mode.
with a porcelain basket, the time necessary
with a porcelain basket, the time necessary
(no water or clothes).
standby mode.
to complete the calibration may be longer.
to complete the calibration may be longer.
*If Calibration Mode is run on a washer
*If Calibration Mode is run on a washer with a porcelain
Calibration cycle runs for approximately
with a porcelain basket, the time necessary
NOTE: Before beginning calibration, check
NOTE: Before beginning calibration, check
basket, the time necessary to complete the calibration may
2–4 minutes. * Cycle completes when lid
to complete the calibration may be longer.
the drive system to verify that the cam on the be longer.
the drive system to verify that the cam on the
unlocks and washer enters standby mode.
splutch is moving freely and not binding.
splutch is moving freely and not binding. NOTE: Before beginning calibration, check the drive system
NOTE: Before beginning calibration, check
*If Calibration Mode is run on a washer
to verify that the cam on the splutch is moving freely and not
the drive system to verify that the cam on the
To access Calibration Mode, perform steps
To access Calibration Mode, perform steps
with a porcelain basket, the time necessary
binding.
splutch is moving freely and not binding.
1 and 2 of Activating the Service Diagnostic
1 and 2 of Activating the Service Diagnostic
to complete the calibration may be longer.
To access Calibration Mode, perform steps 1 and 2 of
Test Modes. Turn the cycle selector knob
Test Modes. Turn the cycle selector knob
To access Calibration Mode, perform steps
Activating the Service Diagnostic Test Modes. Turn the cycle
NOTE: Before beginning calibration, check
until the status LEDs correspond as follows:
until the status LEDs correspond as follows:
1 and 2 of Activating the Service Diagnostic selector knob until the status LEDs correspond as follows:
the drive system to verify that the cam on the
Test Modes. Turn the cycle selector knob
n "Rinse" LED On
"Rinse" LED On
"Rinse" LED On
splutch is moving freely and not binding.
until the status LEDs correspond as follows:
To access Calibration Mode, perform steps
Sense Wash
"Rinse" LED On Sense Wash
1 and 2 of Activating the Service Diagnostic
Fill
Fill
Test Modes. Turn the cycle selector knob
NOTE: Status LED names may vary between
NOTE: Status LED names may vary between
Sense Wash Rinse
until the status LEDs correspond as follows: NOTE: Status LED names may vary between makes and
makes and models.
makes and models.
Fill
models.
Press the START button to begin washer
Press the START button to begin washer
NOTE: Status LED names may vary between "Rinse" LED On
Press the START button to begin washer calibration. All status
calibration. All status LEDs will turn on.
makes and models. calibration. All status LEDs will turn on.
LEDs will turn on.
Press the START button to begin washer
Sense Wash Rinse

UI TEST MODE

UI TEST MODE
Fill
calibration. All status LEDs will turn on.
NOTE: Status LED names may vary between UI Test Mode
To access UI (User Interface) Test Mode, perform
To access UI (User Interface) Test Mode, perform
makes and models.
UI TEST MODE
steps 1 and 2 of Activating the Service Diagnostic
steps 1 and 2 of Activating the Service Diagnostic
To access UI (User Interface) Test Mode, perform steps 1 and 2
Press the START button to begin washer
Test Modes. Turn the cycle selector knob until the
of Activating the Service Diagnostic Test Modes. Turn the cycle
Test Modes. Turn the cycle selector knob until the
To access UI (User Interface) Test Mode, perform
calibration. All status LEDs will turn on.
selector knob until the status LEDs correspond as follows:
status LEDs correspond as follows:
status LEDs correspond as follows:
steps 1 and 2 of Activating the Service Diagnostic
n "Rinse" & "Drain/Spin" LEDs On
Test Modes. Turn the cycle selector knob until the
"Rinse" & "Drain/Spin" LEDs On
UI TEST MODE
"Rinse" & "Drain/Spin" LEDs On
status LEDs correspond as follows:
To access UI (User Interface) Test Mode, perform
(1)Sense (2)Wash (3)Rinse (4)Drain (5)Done
(1)Sense (2)Wash (3)Rinse (4)Drain (5)Done
"Rinse" & "Drain/Spin" LEDs On
steps 1 and 2 of Activating the Service Diagnostic
(1) Fill
(1) Fill
Test Modes. Turn the cycle selector knob until the
NOTE: Status LED names may vary between
NOTE: Status LED names may vary between
NOTE: Status LED names may vary between makes and
(1)Sense (2)Wash (3)Rinse (4)Drain (5)Done
status LEDs correspond as follows:
makes and models. Use LED # identifications.
makes and models. Use LED # identifications.
models. Use LED # identifications.
(1) Fill
Press the START button to begin the UI test.
NOTE: Status LED names may vary between Press the START button to begin the UI test.
"Rinse" & "Drain/Spin" LEDs On
Press the START button to begin the UI test.
makes and models. Use LED # identifications.
Upon entering the UI test mode, all status
Upon entering the UI test mode, all status
n Upon entering the UI test mode, all status LEDs will be
LEDs will be turned ON.
turned ON.
LEDs will be turned ON.
Press the START button to begin the UI test. (1)Sense (2)Wash (3)Rinse (4)Drain (5)Done
(1) Fill
n Pressing the Start button will turn on and off all status
Upon entering the UI test mode, all status
Pressing the Start button will turn on and
Pressing the Start button will turn on and
NOTE: Status LED names may vary between
LEDs, or toggle the state of each status LED independently.
LEDs will be turned ON.
off all status LEDs, or toggle the state of
off all status LEDs, or toggle the state of
makes and models. Use LED # identifications.
(Example: if 2 are on, and 3 are off, then 2 will be turned off
each status LED independently. (Example:
each status LED independently. (Example:
Pressing the Start button will turn on and
and 3 turned on.)
Press the START button to begin the UI test.
if 2 are on, and 3 are off, then 2 will be
if 2 are on, and 3 are off, then 2 will be
off all status LEDs, or toggle the state of
Upon entering the UI test mode, all status
turned off and 3 turned on.)
turned off and 3 turned on.)
each status LED independently. (Example:
LEDs will be turned ON.
if 2 are on, and 3 are off, then 2 will be
Pressing the Start button will turn on and
turned off and 3 turned on.)
DO NOT REMOVE OR DESTROY
DO NOT REMOVE OR DESTROY
off all status LEDs, or toggle the state of
each status LED independently. (Example:
DO NOT REMOVE OR DESTROY
if 2 are on, and 3 are off, then 2 will be
turned off and 3 turned on.)
Rinse Drain Done
Rinse Drain Done
Spin
Spin
Drain Done
Spin
Drain Done
Spin
(4)Spin
(4)Spin
(4)Spin
(4)Spin