Table of Contents
Advertisement
Manual Test Mode (Washer) - See page 2-4 to access Manual Test Mode.
Pressing the START button will activate/deactivate each output. When the output is activated, the corresponding Status LEDs will
flash. IMPORTANT: Lid must be closed and locked to perform SPIN & AGITATE tests.
OUTPUT
Output Details
NOTE: Outputs will time-out after 5 minutes.
LID LOCK
Lock and unlock the lid. NOTES: When lock is enabled, the "Lid Lock" LED will turn ON. Will only lock when lid
is closed. Will only unlock when basket RPM is 0. If lid is not closed, washer will flash status LEDs on and off.
• If lid does not lock or unlock, go to TEST #7: Lid Lock, page 3-15.
COLD VALVE
Turns ON and turns OFF cold water valve.
• If valve does not turn on, go to TEST #2: Valves, page 3-7.
HOT VALVE
Turns ON and turns OFF hot water valve.
• If valve does not turn on, go to TEST #2: Valves, page 3-7.
RESERVED FOR FUTURE DEVELOPMENT
If selected, status LEDs will flash on and off.
RESERVED FOR FUTURE DEVELOPMENT
If selected, status LEDs will flash on and off.
RESERVED FOR FUTURE DEVELOPMENT
If selected, status LEDs will flash on and off.
RESERVED FOR FUTURE DEVELOPMENT
If selected, status LEDs will flash on and off.
DRAIN
Turns ON and turns OFF the drain pump.
• If pump does not turn on, go to TEST #6: Drain Pump, page 3-14.
RESERVED FOR FUTURE DEVELOPMENT
If selected, status LEDs will flash on and off.
LOW SPIN – To perform test, lid must be closed and locked.
Spins basket from 0 to 500 RPM. NOTE: Allow up to 15 seconds for shifter to reposition. IMPORTANT: To activate Low Spin,
must read "0" and lid must be closed with lid lock enabled. If lid is not closed, status LEDs will flash on and off. IMPORTANT:
Water in tub must be drained before test.
• If motor does not spin, go to TEST #3a & 3b: Drive System (Shifter & Motor), pages 3-8 & 3-10.
HIGH SPIN – To perform test, lid must be closed and locked.
Spins basket from 0 to maximum RPM. NOTE: Allow up to 15 seconds for shifter to reposition.
IMPORTANT: To activate High Spin, RPM must read "0" and lid must be closed with lid lock enabled. If
lid is not closed, status LEDs will flash on and off. IMPORTANT: Water in tub must be drained before test.
• If motor does not spin, go to TEST #3a & 3b: Drive System (Shifter & Motor), pages 3-8 & 3-10.
GENTLE AGITATION – To perform test, lid must be closed and locked.
Shifts from idle motor to gentle CW/CCW agitation. NOTE: Allow up to 15 seconds for shifter to reposition.
IMPORTANT: To activate Gentle Agitation, RPM must read "0" and lid must be closed with lid lock enabled. If lid is not
closed, status LEDs will flash on and off.
• If motor does not agitate, go to TEST #3a & 3b: Drive System (Shifter & Motor), pages 3-8 & 3-10.
HEAVY AGITATION – To perform test, lid must be closed and locked.
Shifts from idle motor to gentle CW/CCW agitation. NOTE: Allow up to 15 seconds for shifter to reposition.
IMPORTANT: To activate Gentle Agitation, RPM must read "0" and lid must be closed with lid lock enabled. If lid is not
closed, status LEDs will flash on and off.
• If motor does not agitate, go to TEST #3a & 3b: Drive System (Shifter & Motor), pages 3-8 & 3-10.
For Service Technician Use Only
DIAGNOSTICS & TROUBLESHOOTING
STATUS LEDs
8
8
8
8
8
27" Stacked Laundry Center
= ON
1
2
2
1
4
4
1
4
2
4
2
1
1
On
2
On
2
1
On
4
On
2-11
n
Hide quick links:
Advertisement
Table of Contents
