ADTEK CPM-10 Operation Manual page 21

Operating Steps
■
Engineer level
Parameters
C-3 )00
aOls
5)00
C-4
aOhs
)00
C-5
aOzo
)00
C-6
aOsn
none
C-7
Zsclr
C-8 11)00
aOlt
Back to C-1
Engineer level
Parameters
rs485 RS485
GROUP
group
P 1s Back
ENT
1
D-1
adres
9600
D-2
baud
NstB2
D-3
prity
Back to D-1
( )
AO Output
Display
A/O Low scale Setting range:
range: -199.99~299.99
A O high /
Setting range:
scale range:
-199.99~299.99
Setting range
A O signal
/
zero fine -32768~32767
tunning
:
A O signal span / Setting range:
-32768~32767
fine tunning:
Clear fine tunning Setting range:
value: NONE/AO.ZRO/AO.SPN/BOTH
A/O range limit:
Setting range in
% :0. 00
Press
1 sec to measuring page
( RS 485 )
Output
Display
RS485
GROUP
Display
Address setting:
Setting range:1~255
Modbus Baud rate: Setting range:
1200/2400/4800/9600/
19200/38400
Modbus pairty bit: Setting range:
n.stb.1/n.stb.2/odd/even
Press
1 sec to measuring page
Setting
Shift
Ex When A O set :
0~199.99
display value is 5 , A/O will give 4mA output
Shift
Ex When A O set :
0 199.99 ~
display value is 1 5 , A/O will give 20mA output
:
Shift
When A/O low value is different from display (low),fine
tunning can be done from front panel. During tunning
please connect a higher accuracy meter, to measure
output signal, so as calibration is within accuracy
Shift
When A/O high value is different from display
(high),fine tunning can be done from front panel. During
tunning please connect a higher accuracy meter, to
measure output signal, so as calibration is within
accuracy。
n o n e (
a O z r o (
a O s p n (
b o t h (
Shift
~110. 00%
Press
when done press
to previous selection list
Shift
Setting
Press
Press
when done press
to previous selection list
Press
when done press
to previous selection list
N s t B 1 ( .
N s t B 2 ( .
o d d (
e v e n (
20 24 /
Shift Increase Decrease
Operation
Increase Decrease
A 4 - 2 0
/ (4~20mA)
a O l s
user may set [ ] (Ao.LS)
Increase Decrease
/ A 4 - 2 0 (4~20 mA display value as
a O h s
user may set [ ] ( Ao HS 15so when,
Increase Decrease
Increase Decrease
Enter
Cycle
None ) : None clear
Ao Zro . ) : Zero clear
. ) :
Ao SPn Span clear
) : &
both Zero span clear
Increase Decrease
, &
values blink press , change value or selection
to next setting or hold
Increase Decrease
Operation
1 sec to [ r s 4 8 5 g r o u p
, &
values blink press , change value or selection
to next setting or hold
, &
values blink press , change value or selection
to next setting or hold
Enter
Cycle
n Stb .1): None, 1 stop bit
n Stb .2): None, 2 stop bit
odd odd ):
EvEn Even ):
Enter
Enter
display value as
5 so when,
Enter
)
. )
Enter
Enter
Enter
1 sec .
Enter
]
1 sec .
1 sec .