ADTEK CPM-10 Operation Manual page 17

Operating Steps
■
Engineer level
Parameters
5
A-9
avg-p
off
A-10
w-div
)2
A-11
lOcut
0000
A-12
tLrst
1000
A-13
Pcode
none
A-14
Flocy
Return to A -1
Engineer level
Parameters
RELAY
relay
GROUP
group
P 1s Back
ENT
Uavg
B-1
r!!sl
Display
Active power
Setting range:2~99
average value
setting range:
Watt high-
Setting range
resolution
OFF:0(Normal)
ON:1(High)
Low Cut
Setting range 0.0 100.0%
Reset active Password:0 9999
energy/reactive
energy to zero
Rs485 write in "0" to reset
Password:0000 9999
Change
parameters level
password:
Function lock select:
NONE/USER/ENG/ALL
Press
1 sec to measuring page
( Raely Output )
Display
RELAY
GROUP
Display
Reference to corresponding
Relay R1.1
table table B 1) (
parameters page:
.
v a v g 3 Phase average voltage
i a v g .
3 Phase average current
f r e q
p . t l
3 Phase active power
q . t l
3 Phase reactive power
s . t l
3 Phase apparent power
p f . a v g 3 Phase power factor
a e . t l 3 Phase active energy
r e . t l 3 Phase reactive energy
v - a A Phase voltage
v - b
B Phase voltage
v - c
C Phase voltage
i - a
A Phase current
i - b B Phase current
i - c C Phase current
p f - a A Phase power factor
p f - b B Phase power factor
p f - c C Phase power factor
p - a
A Phase active power
p - b B Phase active power
p - c C Phase active power
q - a A Phase reactive power
q - b B Phase reactive power
q - c C Phase reactive power
s - a
A apparent power
s - b
B apparent power
s - c C apparent power
Shift
Setting
Shift
※System may have interference or signal unstable
sometimes, causing display unstable: This function help
to decrease rapid change on the display. Increasing
average value make display more stable,
Shift
:
Press
when done press
※
Default :OFF
to previous selection list
:
~
Shift
Press
when done press
※
Default 0.2 :
to previous selection list
~
Shift
Press
when done press
to previous selection list
Shift
~
Press
when done press
to previous selection list
Shift
n o n e (
setting
u s e r (
change parameters value
e n g (Programming Level): Parameters setting lock ,can view
setting cant change parameters value
a l l (All Level): All level lock，can view setting cant change
parameters value
Setting
Press
Shift
-
Press
Default
:V.AVG
when done press
to previous selection list
Frequency
Note: R1.1/R1.2/R1.3 is only one relay output
function, but three mode (.1/.2./.3-) group can
be set to function
In (.1/.2./.3) group within any parameters set
the conditions for the establishment of the
relay action. But when the three groups of
conditions have not set up the relay is still
conduction until three parameter is not set up
until reversion
EX: the R1.1 setting parameters for
when the R1.2 setting parameters to set
parameters for
current average set point is reached, the relay
actionuntil below the set point automatically
reset.
When the three set parameters set point is
reached, if only to exclude the R1.1 set point,
then the relay is still action, until the R1.2 with
R1.3 setpoint exclusion will revert to.
1 / 6 24
Increase Decrease
Operation
Increase Decrease
Increase Decrease
, &
values blink press , change value or selection
to next setting or hold
Increase Decrease
, &
values blink press , change value or selection
to next setting or hold
Increase Decrease
, &
values blink press , change value or selection
to next setting or hold
Increase Decrease
, &
values blink press , change value or selection
to next setting or hold
Increase Decrease
) : ,
None No function lock user can enter and change
User Level User level lock can view setting cant ): ,
Operation
r e l a y g r o u p
1 sec [ ]
Increase Decrease
, &
values blink press , change value or selection
to next setting or hold
i . a v g , R1.3 f r e q
Enter
Enter
Enter
1 .
sec
Enter
1 sec .
Enter
1 sec .
Enter
1 sec .
Enter
Enter
1 sec .
v . a v g ,
. Only R1.1