Table of Contents
Advertisement
TRANSPORT AND UNPACKING
D
•
The packed parts should be handled as indicated in the
symbols and markings on the outside of the packing.
•
Before installing the equipment, ensure that the area to
be used is large enough for such purposes, is properly
lit and has a clean, smooth floor surface.
The user is responsible for the operations of unlo-
ading and handling and should use the maximum
care so as not to damage the individual parts or
injure anyone.
To perform the unloading operation, use only
qualified and trained personnel (truck and cra-
ne operators, etc.) and also suitable hoisting
equipment for the weight of the installation or its
parts. Follow carefully all the safety rules.
The personnel must be equipped with the neces-
sary safety clothing.
•
The manufacturer will not be responsible for the unloading
operations and transport to the workplace of the machine.
•
Check the packing is undamaged on receipt of the
equipment. Unpack the machine and verify if there has
been any damage due to transportation.
In case of damage, call immediately LARIUS and the
Shipping Agent.
All the notices about possible damage or anomalies
must arrive timely within 8 days at least from the date
of receipt of the plant through Registered Letter to the
Shipping Agent and to LARIUS.
The disposal of packaging materials is a custo-
mer's competence and must be performed in
accordance with the regulations in force in the
country where the plant is installed and used.
It is nevertheless sound practice to recycle
packaging materials in an environment-friendly
manner as much as possible.
SAFETY RULES
E
•
The employer shall train its employees about all those
risks stemming from accidents, about the use of safety
devices for their own safety and about the general rules
for accident prevention in compliance with international
regulations and with the laws of the country where the
plant is used.
•
The behaviour of the employees shall strictly comply with
the accident prevention and also environmental regulations
in force in the country where the plant is installed and used.
Ed. 002 - 01/2017
Read carefully and entirely the following instructions
before using the product.
Please save these instructions in a safe place.
The unauthorised tampering/replacement of one
or more parts composing the machine, the use of
accessories, tools, expendable materials other than
those recommended by the manufacturer can be a
danger of accident.
The manufacturer will be relieved from tort and
criminal liability.
•
Keep your work place clean and tidy. Disorder where you
are working creates a potential risk of accidents.
•
Always keep proper balance avoiding unusual stance.
•
Before using the tool, ensure there are not damaged parts
and the machine can work properly.
•
Always follow the instructions about safety and the regu-
lations in force.
•
Keep those who are not responsible for the equipment out
of the work area..
•
Never exceed the maximum working pressure indica-
ted.
Never point the spray gun at yourselves or at other people.
•
The contact with the casting can cause serious injuries.
•
In case of injuries caused by the gun casting, seek imme-
diate medical advice specifying the type of the product
injected. Never undervalue a wound caused by the injection
of a fluid.
•
Always disconnect the supply and release the pressure in
the circuit before performing any check or part replacement
of the equipment.
•
Never modify any part in the equipment. Check regularly
the components of the system. Replace the parts damaged
or worn.
•
Tighten and check all the fittings for connection betwe-
en pump, flexible hose and spray gun before using the
equipment.
•
Always use the flexible hose supplied with standard kit.
The use of any accessories or tooling other than those
recommended in this manual, may cause damage or injure
the operator.
•
The fluid contained in the flexible hose can be very dan-
gerous. Handle the flexible hose carefully. Do not pull the
flexible hose to move the equipment. Never use a damaged
or a repaired flexible hose.
The high speed of travel of the product in the hose
can create static electricity through discharges
and sparks. The pump is earthed through the earth
with sliding chain.
DRAGON LINER
www.larius.eu
9
Advertisement
Table of Contents
