Egholm Park Ranger 2150 Operator's Manual
  1. Manuals
  2. Brands
  3. Egholm Manuals
  4. Utility Vehicle
  5. Park Ranger 2150
  6. Operator's manual

Egholm Park Ranger 2150 Operator's Manual

Basic machine
Hide thumbs Also See for Park Ranger 2150:
Table of Contents

Advertisement

Quick Links

O
'
peratOr
s manual
BASIC MACHINE
Park Ranger 2150
Park Ranger 2150
3
1
in
All Year
Operation
Cost Saving

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Park Ranger 2150 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Egholm Park Ranger 2150

Summary of Contents for Egholm Park Ranger 2150

  • Page 1 ’ peratOr s manual BASIC MACHINE Park Ranger 2150 Park Ranger 2150 All Year Operation Cost Saving...
  • Page 2 We ask you to pay particular attention to section 1.1. Safety. The machine must only be serviced by professionals. The Park Ranger 2150 is designed only for use by professionals. On delivery, the user will receive thorough training to become a competent operator.

  • Page 3: Table Of Contents

    3.3 Service and maintenance chart for the Park Ranger 2150 .......
  • Page 4 Introduction The Park Ranger 2150 utility machine The Park Ranger 2150 is an Egholm utility machine with a complete range of special attachments designed to allow you to perform outdoor maintenance work all year round. Sweeping and vacuuming in spring and autumn, mowing grass and lawn-edge cutting in the summer, and sweeping snow, and spreading gravel and sand in the winter.

  • Page 5: General Information

    Make sure that no one is standing near the machine while it is in use. (Picture 1) Turn the steering wheel carefully The Park Ranger 2150 is articulated and the steering mechanism is extremely responsive. (Picture 2) Articulated joint...
  • Page 6 Use approved hearing protection Park Ranger 2150. Maintenance Before carrying out servicing and maintenance please make sure to pull the hand brake, stop the engine and turn off the main switch of the machine. Operator’s Manual Park Ranger 2150...

  • Page 7: Attachments

    There is an operator’s manual for each attachment. Operation with these attachments must follow the instructions outlined in the relevant operator’s manual. Do not operate the Park Ranger 2150 with the attachment unless all instructions have been followed. Operator’s Manual Park Ranger 2150...

  • Page 8: Ec Declaration Of Conformity

    A XXXXX (serial number) · has been manufactured in conformity with Directive 2006/42/EU Person authorized to compile the technical documentation: Knud Olsen Egholm A/S Transportvej 27 7620 Lemvig Place: Lemvig Date: Signature: Knud Olsen, Senior Engineer Operator’s Manual Park Ranger 2150...

  • Page 9: Technical Data

    EU Norm Stage lllA Please refer to the engine operator’s manual for additional technical data Fuel Fuel Diesel Fuel tank capacity 20 l diesel At 2,400 rpm approx. 2.8 l/h At 3,400 rpm approx. 4.6 l/h Operator’s Manual Park Ranger 2150...
  • Page 10 Whole body, EN 13059 0.6 m/s Hand/arm, EN 13059 2.4 m/s Turning radius Park Ranger 2150 has an extremely small turning radius 1.5 m Information plate Mounted on the right side of the front chassis Attention Specifications may change without notice.
  • Page 11 General information 1.4 Technical data - continued Falling Object Protective Structure - FOPS Park Ranger 2150 and its attachments do not operate when falling objects are a risk. Roll-Over Protective Structure - ROPS Tested according to Directive 86/298/EEC and fulfills OECD Code 7.

  • Page 12: Access To The Cab

    The doors will open when you press the door handle down. (Picture 4) Outside door handle button Both doors can be used as an emergency exit. Cab floor Inside door handle - Press down Operator’s Manual Park Ranger 2150...
  • Page 13 The cab is equipped with a roof hatch. The roof hatch will open when you push the handle upwards. (Picture 3) Pull out small button Pull back handle for window to open Roof hatch handle Operator’s Manual Park Ranger 2150...

  • Page 14: Steering Column

    General information 1.6 Steering column Steering column 1. 12V Connector. 2. Horn switch. 3. Ignition key. Operator’s Manual Park Ranger 2150...
  • Page 15 General information 1.6 Steering column - continued 4. Hazard lights. 5. Instrument panel switch to switch between rpm and the timer. 6. Switch - electrical socket back. 7. Instrument panel. Operator’s Manual Park Ranger 2150...
  • Page 16 +5 °C. way to start the Park Ranger 2150. Check the oil level. If this is OK, restart the machine. The 11. Shows rpm or time (h).
  • Page 17 General information 1.6 Steering column - continued Steering column 1. Throttle. 2. Handbrake. 3. Indicator light switch/stalk. 4. Fuses. See section 1.13. Operator’s Manual Park Ranger 2150...

  • Page 18: Operational Features

    5. Speed regulation of attachments (defined by the attachment) Regulates the oil flow in hydraulic connectors B and C. Warning Keep the quick action couplings clean of dirt. Hydraulic connectors D1, D2, D3 Lever D Speed regulation Operator’s Manual Park Ranger 2150...
  • Page 19 The transport lock must always be activated when the utility machine is being driven from one location to another. The transport lock locks the A-frame in place so that the Transport lock activated A-frame cannot be lowered during driving. (Picture 3+4) Operator’s Manual Park Ranger 2150...
  • Page 20 The towing lever is in closed position when the lever is vertical. Towing lever closed The towing lever is fitted to the transmission pump and is located under the rear chassis of the Park Ranger 2150. Operator’s Manual Park Ranger 2150...

  • Page 21: Fitting A Cab (Optional)

    Open the heat regulation system in the cab. Start the machine and let it run in neutral for 5 minutes. Stop the Connection for windscreen wiper machine. Refill coolant, see Section 3.7. Hoses Electrical cables Operator’s Manual Park Ranger 2150...

  • Page 22: Operating Panel, Cab (Optional)

    7. Windscreen wipers: Wipe. 8. Cab heater: Position 1. Half power. Position 2. Full power. 9. Plug for headphones. 10. Ceiling light: Position 1. White light. Position 2. Red light. 11. Radio (see operator´s manual for radio). Operator’s Manual Park Ranger 2150...

  • Page 23: Removable Load Carrier (Optional)

    C) Make sure that the locking handle is locked in position in the locking eye. Pull the load carrier to make sure that it is locked in position. (Picture 4) Locking eye Locking handle Locking handle in “released” position Locking handle in “released” position Operator’s Manual Park Ranger 2150...

  • Page 24: Driver's Seat

    A) The oil cooler cover is removed downwards at an angle. Fitting A) Insert the top edge of the oil cooler cover at an angle under the rim of the opening in the Park Ranger 2150. Fitting the oil cooler cover (Picture 2) B) Push the oil cooler cover into position.

  • Page 25: Fuses And Main Switch

    (50 Amp) is located in the engine compartment below the exhaust pipe. (Picture 3) Main switch To start the Park Ranger 2150, the main switch on the left- hand side of the machine must be ON. The main switch controls all power to the machine.

  • Page 26: Fuses And Relay Overview

    Plug for Snow V-blade Dipped headlights Supply flash Cabin fan / Trailer plug Rotary light / System for windscreen wiper Working light rear / Radio Parking light / Radio (emergency supply) Relay start Relay preheat control Operator’s Manual Park Ranger 2150...
  • Page 27 Relay placed below the driver´s seat KT2 Preheat timer KT3 Seat timer KT4 Impuls relay (intentional startup) K3 Anti startup K4 Hot bulb timer feedback K5 Intentional startup (safty) K6 Intentional startup (safty) K7 Brake light K8 Lights Operator’s Manual Park Ranger 2150...

  • Page 28: Operator's Manual

    Must be visible in the glass. Filling – see “Maintenance”, Section 3.4. (Picture 2) Engine oil The oil level must be between the two lines on the dipstick. Filling – see Section 3.5. (Picture 3) Engine oil Operator’s Manual Park Ranger 2150...
  • Page 29 Tank capacity: 20 litres. The control light comes on when 5 litres remain = sufficient for approx. 1½ hours. This light can only work when the Park Ranger 2150 is switched on. (Picture 2+3) Control light for diesel Topping up Diesel...

  • Page 30: Starting, Operating And Stopping

    (5) lights up along with the other warning lights. When the pre-heater indicator goes out, turn the key farther clockwise and the Park Ranger 2150 will start. G) Release the brake pedal (1) to its top position. H) You can now activate the drive pedal(6).
  • Page 31 C) Press the brake pedal (1) down to its lowest position and slide the parking brake (2) forward. (Picture3) D) Stop the Park Ranger 2150 by turning the key back to the starting position. (Picture 3) Operation with front-mounted attachments If an attachment is fitted to the Park Ranger 2150, it must be raised above the ground before the machine is driven.

  • Page 32: Service And Maintenance

    Service and Maintenance 3.1 Daily maintenance The daily maintenance of the Park Ranger 2150 is simple and straightforward – but very important. Three operations need to be performed: cleaning of the radiator, oil cooler and air filter. Cleaning the radiator...

  • Page 33: Lubrication

    There are two lubricating nipples by the A-frame, and four by the steering cylinders. (Picture 1+2) Lubricating nipples, A-frame Cables and moving parts Lubricate with a few drops of oil every 15 hours or so. Lubricating nipples, steering cylinders Operator’s Manual Park Ranger 2150...

  • Page 34: Service And Maintenance Chart For The Park Ranger 2150

    7. Lubricate the machine for every 15 hours of operation. 8. We recommend replacing the air filter for every 200 hours. We recommend that service and maintenance procedures are carried out by authorised Egholm dealers Operator’s Manual Park Ranger 2150...
  • Page 35 Service and Maintenance 3.3 Service and maintenance chart for the Park Ranger 2150 - continued t Clean n Lubricate m Check l Replace Operation Service schedule Daily 4000 h 4400 h 4800 h 5200 h 5600 h 6000 h 6400 h 6800 h 7200 h 7600 h...

  • Page 36: Hydraulic System

    (Picture 3) Tank filter housing Hydraulic oil filter A) Remove the oil filter under the Park Ranger 2150 and let the oil run out until the tank is empty. B) Lubricate the gasket with oil. C) Fit the new filter.

  • Page 37: Engine Maintenance

    Check the engine oil Check the oil level 1. Park the Park Ranger 2150 on a level surface. 2. Check the oil level before starting the engine. (Picture 1) 3. Pull out the dipstick, wipe it clean and then replace it.
  • Page 38 4. Turn the engine on and let it run for a while to check that the filter seal is tight. 5. Switch off the engine and check the level of engine oil. 6. Add oil if the level of engine oil drops after the filter has been changed. Operator’s Manual Park Ranger 2150...

  • Page 39: Fuel

    3. Bleed the fuel system. It is important to bleed the fuel system 1. When the fuel filter and hoses have been removed and then replaced. 2. If the engine has run out of fuel. Operator’s Manual Park Ranger 2150...
  • Page 40 Checking the fuel hoses during every service 1. Check for loose clips. Apply a little oil to the screw and tighten. 2. If any fuel hoses or clips appear worn, replace them immediately. 3. Bleed the fuel system after replacing hoses. Operator’s Manual Park Ranger 2150...

  • Page 41: Radiator

    C) Replace the radiator cap carefully after filling up with coolant. D) Start the Park Ranger 2150 and let it run until it reaches operating temperature. E) Stop the engine and add coolant. (Picture 2) Check the radiator/cooler hoses Replace the hoses and clips every two years –...

  • Page 42: Air Filter

    3.8 Air filter Cleaning the air filter Open the vacuum valve every day to remove large particles of dirt and dust when the Park Ranger 2150 is being used in dusty environments. Air filter housing A) Open the air filter housing.

  • Page 43: Battery

    The first type of battery is maintenance free so no maintenance will be necessary. The second type of battery is a battery where maintenance will be necessary. Check the level once a year. Top up as necessary with ONLY demineralised water. (Picture 1) Operator’s Manual Park Ranger 2150...

  • Page 44: Fan Belt

    The Park Ranger is equipped with 2 towing points in front and 2 towing points at the rear. (Picture 3+4) These towing points are also used for safe transport of the Towing point - Front Park Ranger on trailers etc. Towing point - Rear Operator’s Manual Park Ranger 2150...

  • Page 45: Tire Change

    Service and Maintenance 3.14 Tire change When a tire needs changing the Park Ranger 2150 must only be lifted with a jack in the points indicated at picture 1+2. Warning A tire change must be performed on a flat and stable ground only!

  • Page 46: Conditions

    Conditions 4.1 Warranty The warranty period for the materials and manufacture of this Park Ranger 2150 is 12 months from the date of purchase. In case of errors or defects on the machine within the warranty period, Egholm will carry out the necessary repairs at no charge to the customer, including materials and working hours, in accordance with the terms and conditions listed below.

  • Page 47: Complaints

    Egholm A/S 4.3 Disposal When, many years from now, your Park Ranger 2150 has reached the end of its working life, it should be disposed of in a responsible manner that conforms to relevant disposal regulations. 1. Used hydraulic oil, engine oil, diesel oil, coolant and AC coolant are to be delivered at an approved waste disposal facility or site.

  • Page 48: Wearing Parts

    Wearing parts 5.1 Wearing parts – Park Ranger 2150 E01100250 Tyres and wheels E90501643 Filter kit 2150 E01006500 Air filter E01020020 Oil filter E04003050 Hydraulic filter E01020010 Fuel filter E04003060 Hydraulic oil filter E50000656 Fan belt 2150 E05001080 Bulb, main light E05001050 Bulb, rotary light Operator’s Manual Park Ranger 2150...
  • Page 49 Wearing parts 5.1 Wearing parts – Park Ranger 2150 - continued E04501200 Hydraulic connector, male, 1/4” E05001090 Bulb, indicator switch E04501220 Hydraulic connector, male ½” E05001010 Bulb, indicator E04501210 Hydraulic connector, male3/8” E05001040 Bulb, parking light, front E04501230 Hydraulic connector, female, 1/4”...

  • Page 50: Notes

    Notes Operator’s Manual Park Ranger 2150...
  • Page 51 Notes Operator’s Manual Park Ranger 2150...
  • Page 52 Egholm A/S Transportvej 27 DK-7620 Lemvig T. +45 97 81 12 05 F. +45 97 81 12 10 www.egholm.eu info@egholm.dk E90001082-B0_01 EN...

Table of Contents