Egholm Park Ranger 2150 Operator's Manual

Hide thumbs Also See for Park Ranger 2150:

Advertisement

Quick Links

O
'
peratOr
s manual
LAWN EDGER
Park Ranger 2150

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Park Ranger 2150 and is the answer not in the manual?

Questions and answers

Summary of Contents for Egholm Park Ranger 2150

  • Page 1 ’ peratOr s manual LAWN EDGER Park Ranger 2150...
  • Page 2 Reservations: As it is the Egholm policy to make continuous improvements, we reserve the right to alter the machine’s specifications and equipment at any time without notice. Egholm accepts no liability for errors or shortcomings in the operator’s manual.
  • Page 3: Table Of Contents

    5.1 Wearing parts – Park Ranger 2150 lawn edger ....... .
  • Page 4: General Information

    Do not drive on slopes with an incline of more than 10°. (Picture 4) Warning! Rotating parts Máx. 10° Do not drive on slopes with an incline of more than 10° Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 5: Ec Declaration Of Conformity

    · has been manufactured in conformity with the provisions of the Machinery Directive, Directive 2006/42/EU The Park Ranger 2150 fitted with the FH 2100 cab (ROPS approved) · has been tested at the Danish Institute of Agricultural Sciences at Bygholm...
  • Page 6: Technical Data

    Technical data: Type 22VKS1 Weight of lawn edger 58 kg Ground clearance below scraping edge, lifted 140 mm Max. cutting depth 95 mm Offset 150 mm Specifications may be changed without prior notice. Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 7: Operator's Manual

    (Picture 2) 5. Switch off the engine. 6. Use the locking handle on the A-frame to lock the lawn A B C edger in place. (Picture 3) Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 8 8. Push the lock button down to release the support strut; pull the strut up until the lock clicks into place (Picture 2) Removal: Follow the procedure for fitting in the reverse order. Lever D Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 9: Before Start-Up

    When turning, the rear of the machine Lower the lawn edger – Lever A in position 2 swings out so there is a risk of crushing or collision. Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 10: Adjustment

    4. Switch off the machine. A B C 5. Loosen the support wheel (Picture 4) 6. Adjust the support wheel to the desired depth. Lever A 7. Re-tighten the handle. Transport lock Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 11 5. Loosen the sideways grip of the blade. (Picture 4) Lever A 6. Adjust the position of the blade as desired. The blade must not be positioned beyond the arrow. (Picture 4) 7. Re-tighten the handle. Transport lock Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 12: Replacing The Blade

    Removing the bolt end piece and tighten again. 7. Refit the guard. Blade for cutting away from the machine (Picture 3) Blade for cutting towards the machine (Picture 4) Sharp edge Sharp edge Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 13: Service And Maintenance

    5. Remove the end piece, pipe and blade. (Picture 2) 6. Disassemble the nuts and bolts that secure the cultivator blades and remove the blades. (Picture 3) 7. To fit the new cultivator blades, reverse the procedure. Sharp edge Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 14 4. Remove the bolt that secures the blade. (Picture 2) Detaching the guard 5. Remove the end piece, pipe and blade. (Picture 2) 6. To fit the new blade, reverse the procedure. Removing the bolt Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 15 When it is time to store the lawn edger for the winter, we recommend the following steps: 1. Remove any loose paint and repaint any damaged areas. 2. Spray the lawn edger with protective lubricant. Screws that secure the wearing rail Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 16: Fitting Instructions For The 2150/2200 Lawn Edger Adapter

    2. Place the adapter frame in the A-frame on the attachment. (Picture 2) Covering material 3. Push the width bolts through the plate, and position the plate in the adapter frame. (Picture 3) Adapter frame Width bolts Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 17 4. Place washers and nuts on the bolts, and then tighten. (Picture 1) 5. Attach the hydraulic hoses. (Picture 2) Tighten the nuts. Male connector on opposite end Female connector on opposite end Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 18: Conditions

    The warranty period for the materials and manufacture of the lawn edger is 12 months from the date of purchase. In case of errors or defects on the machine within the warranty period, Egholm will carry out the necessary repairs at no charge for materials and working hours in accordance with the terms and conditions listed below.
  • Page 19: Complaints

    2. Remove the plastic and rubber parts and dispose of them in accordance with the applicable environmental legislation. 3. After the parts mentioned have been removed, the machine is ready to be handed over to an authorised municipal scrap merchant. Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 20: Wearing Parts

    Wearing parts 5.1 Wearing parts – Park Ranger 2150 lawn edger 09701270 Rubber wheel 09701070 Nylon wearing rail 09722710 Rubber guard 01700040 Bearing for rubber wheel 09806930 Blade 90501481 Cultivator blade set for lawn edger – left 90501701 Cultivator blade set for lawn edger –...
  • Page 21: Notes

    Notes Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 22 Notes Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 23 Notes Operator’s Manual – Park Ranger 2150 Lawn edger...
  • Page 24 Egholm A/S Transportvej 27 DK-7620 Lemvig T. +45 97 81 12 05 F. +45 97 81 12 10 www.egholm.eu info@egholm.dk 90101501-01 UK...

This manual is also suitable for:

22vks1

Table of Contents