Related Manuals for J-Tech Digital JTECH-EXBT460
Summary of Contents for J-Tech Digital JTECH-EXBT460
- Page 1 Operating Instructions Website: www.jtechdigital.com Toll Free: 1-888-610-2818 Email: support@jtechdigital.com USER MANUAL J-Tech Digital® 18G HDMI Extender with Audio Breakout Model: JTECH-EXBT460 JTD-ID: 460...
-
Page 2: Safety Precaution
Refer all servicing to qualified service personnel. ⚫ After-sales Service We provide limited warranty for the product within three years. Packing List 1x JTECH-EXBT460 Transmitter 1x JTECH-EXBT460 Receiver ⚫ ⚫ 2x TX Mounting Ears with 4 Screws 2x RX Mounting Ears with 4 Screws ⚫... -
Page 3: Product Introduction
Product Introduction Thanks for choosing the JTECH-EXBT460 HDMI 2.0 Extender, which consists of a transmitter and a receiver. It can extend 4K video to distance up to 131 feet (40 meters) and 1080P video to distances up to 230 feet (70 meters) over a single CATx cable. It supports audio de-embedded and ARC. - Page 4 Transmitter Panel Description I R I n I R O u t H D B T O u t HDMI In ARC Audio Out HDCP LINK ① Power LED: The LED illuminates red when power is applied. ② Test Pattern: Press the button with paper clip or other sharp tool to enable the test pattern, and the left LED illuminates blue, the product generates an image of 1080P/60Hz color bar to output;...
- Page 5 Receiver Panel Description ① Power LED: The LED illuminates red when power is applied. ② ARC Mode: Press the button with paper clip or other sharp tool to enable the ARC mode, and then the left LED illuminates blue. Press it again to exit the ARC mode and the LED is off.
-
Page 6: Edid Management
DIP Switch Operation EDID Management The Extended Display Identification Data (EDID) is used by the source device to match its video resolution with the connected display. By default, the source device obtains its EDID from the first connected display. Meanwhile, since the displays with different capabilities are connected to the extender, the DIP switch on the front panel of transmitter can be used to set the EDID to a fixed value to ensure the compatibility in video resolution. - Page 7 Multi-CH (Supports PCM 3840x2160@60Hz HDR 2CH, PCM5.1, Dolby Digital 5.1,DTS 2CH) User-defined EDID (Upload the EDID by Micro-USB port) Note: 2CH: Supports LPCM 2CH. ⚫ Multi-CH: Supports LPCM 8CH, Dolby TrueHD, DTS-HD , Dolby Digital5.1, DTS ⚫ 5.1, Dolby Digital Plus. User-defined EDID Setting ⚫...
-
Page 8: Hdcp Mode
HDCP Mode Put the switch 4 on the “ON” position to select HDCP Active mode, or on the “OFF” position for HDCP Passive mode. Switch Status Mode HDCP Passive Automatically follows the HDCP version of source OFF (0) (Default) device. If the input video has HDCP content, the HDCP ⚫... -
Page 9: System Connection
The TV audio can’t be back to the ARC Audio Out port of transmitter. The Audio Breakout port of receiver is connected to speaker or amplifier for HDMI source audio de-embedding. System Connection The following diagram illustrates the typical input and output connection of the extender: HDMI: Audio:... -
Page 10: Technical Specification
Technical Specification Transmitter Receiver Video Input (1) HDMI (1) HDBT Input Connector (1) Type-A female HDMI (1) RJ45 Up to 4Kx2K@60Hz 4:4:4 8bit Input Resolution Up to 4Kx2K@60Hz 4:2:0 HDR10 Output (1) HDBT Out (1) HDMI Output Connector (1) RJ45 (1) Type-A female HDMI Up to 4Kx2K@60Hz 4:4:4 8bit Output Resolution... - Page 11 (1) 3-pin terminal block (1) 3-pin terminal block General Bandwidth 18Gbps HDMI Standard HDCP Version 2.2, 1.4 compliant Pass-through Bidirectional PoC Supported HDMI 2.0 Cable Length 4K@60Hz 4:4:4 ≤ 5m, 4K@60Hz 4:2:0 ≤ 15m, 1080P ≤ 20m Transmission Standard HDBaseT 1080P@60Hz ≤...
- Page 12 Specifications, pictures & software described herein are subject to change without prior notification. • Only use the provided power supply when operating this unit. J-Tech Digital® is not responsible for any damage due to customer neglect. • All trademarks are the sole property of their respective companies.