Related Manuals for Hope Industrial Systems HIS-RL15- ***D Series
Summary of Contents for Hope Industrial Systems HIS-RL15- ***D Series
- Page 1 Hope Industrial Systems, Inc. User Manual 15” Rack Mount Industrial Monitor Revision D Model Numbers: HIS-RL15- _ _ _ D...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Safety and Regulatory Information Factory Preset Timing Control Panel Buttons and Indicators Direct Functions OSD Functions Picture Color Image On-Screen Display (OSD) Setup Information Information for Resistive Touchscreen Monitors Installation Instructions Cleaning Troubleshooting Drawings Specifications Display Video Electrical Environmental Functional... -
Page 3: Safety And Regulatory Information
Safety and Regulatory Information Warning To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dange- rously high voltages are present inside the unit. Do not disassemble the unit. Refer servicing to qualified personnel only. This equipment is not intended for use in critical applications where its failure to op- erate would create immediate life threatening circumstances. -
Page 4: Factory Preset Timing
Factory Preset Timing Horizontal Vertical Pixel Clock Sync Polarity Frequency Frequency (MHz) (H/V) Resolution (KHz) (Hz) IBM, 640 x 350 31.469 70.086 25.175 IBM, 640 x 480 31.469 59.940 25.175 IBM, 720 x 400 31.469 70.087 28.322 VESA, 640 x 480 37.500 75.000 31.500... -
Page 5: Control Panel Buttons And Indicators
Control Panel Buttons and Indicators Control Panel Button Mode Description Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. MENU Always MagicBright Provides an optimum viewing environment depending on the contents of the image you are watching. Cur- rently four different modes are available. - Page 6 Control Panel Button Mode Description When the OSD Menu is NOT Dis- played Push to adjust brightness. Adjusts items in the menu UP. When the OSD Menu is Being Displayed ENTER When the OSD Activate a highlighted menu item. Menu is Being Displayed Use this button for auto adjustment of the display.
-
Page 7: Direct Functions
Direct Functions Menu Description When the ‘AUTO’ button is pressed, the Auto Adjustment screen ap- pears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automati- cally. -
Page 8: Osd Functions
OSD Functions Important Note: Except for Brightness and Contrast, all of these functions are au- tomatically set by using the AUTO Button. Picture Menu Description Direct Access Feature: When OSD is not on the screen, push the but- Brightness ton to adjust brightness. Adjust the contrast. -
Page 9: On-Screen Display (Osd)
On-Screen Display (OSD) Menu Description Changes the language used in the Menu. Language H-Position Changes the horizontal position of the OSD. Changes the vertical position of the OSD. V-Position Changes the translucency of the background of the OSD. Transparency The menu will automatically turn off if no adjustments are made for a Display Time certain time period. -
Page 10: Information For Resistive Touchscreen Monitors
Information for Resistive Touchscreen Monitors The enclosed CD-ROM contains documentation and drivers for all major operating systems (touchscreen monitors only). To assure you have the most current information, check the following Internet addresses: http://www.hismonitors.com/Touchscreen_Drivers.htm... -
Page 11: Installation Instructions
Installation Instructions Preparing for Installation Important! Perform the following steps BEFORE Installation of the monitor into the panel. 1. Ensure that sufficient power is available. 2. Ensure that sufficient space is available to allow for proper air flow into and out of the unit. -
Page 12: Cleaning
Cleaning CAUTION! DO NOT USE ABRASIVE MATERIALS SUCH AS PAPER TOWELS OR DIRTY SHOP RAGS ON THE DISPLAY AS IT WILL SCRATCH THE PROTECTIVE COATING. ALWAYS USE A SOFT CLOTH, PREFERABLY MADE OF COTTON. Resistive Touchscreen model Any standard glass cleaner can be used to clean the touchscreen. Always spray the glass cleaner on the cloth or towel and then clean the touch- screen. -
Page 13: Troubleshooting
Troubleshooting Blank Screen After installing the power adapter and connecting I/O cable to a PC, the monitor displays a blank screen. • Press the power button and check to see if the power LED is lit. • If the LED turns green, make sure the PC is powered on. Make sure all cables are connected. -
Page 14: Drawings
Drawings Front View... - Page 15 Rear View...
-
Page 16: Specifications
Specifications Display Type Thin-film transistor (TFT) Active Matrix Liquid Crystal Size 15” diagonal Image size 12.0” (304mm) x 9.0” (228mm) Native resolution XGA (1024 x 768) Plug and Play DDC1/2B compatible` Minimum resolution VGA (640 x 480) Pixel pitch 0.297mm x 0.297mm Number of colors 16 million Viewing Angle (Hori/Vert) -
Page 17: Electrical
Horizontal scan 30kHz – 61kHz Supported Video Stan- Std VGA – 640x480 @ 60Hz dards SVGA – 800x600 @ 60Hz XGA – 1024x768 @ 60Hz (Native) Vertical scan 56Hz – 75Hz Response rate (typical) 16ms Electrical Monitor input 90VAC – 264VAC, 50/60Hz (+/- 3Hz) Power consumption Less than 25W Power management... -
Page 18: Enclosure
USB interface to host computer Enclosure Type Rack mount; Standard EIA 19" rack width; 6U height with 4 mounting holes Panel rating Enclosure rating - NEMA 1 Physical Depth 2.15" behind panel Bezel Powder coated carbon steel – matte finish Front bezel outside di- 19.0"... -
Page 19: Warranty Statement
Warranty Statement Who is Covered? This warranty covers the purchaser of this product only and is not transferable without our written consent. What Does This Warranty Cover and What is the Period of Coverage? The warranty remains in force for a three year period beginning on the date we invoice you for the product unless it is a keyboard, for which the warranty period is one year. - Page 20 Hope Industrial Systems, Inc. 1325 Northmeadow Parkway Suite 100 Roswell, GA 30076 www.HISmonitors.com 2006 Hope Industrial Systems, Inc. Publication RL15D September, 2006...
Need help?
Do you have a question about the HIS-RL15- ***D Series and is the answer not in the manual?
Questions and answers