Related Manuals for Mytee Prep Center S 80-120
Summary of Contents for Mytee Prep Center S 80-120
- Page 1 User Manual Prep Center S ™ Model: 80-120 REV. 4/10/19 13655 Stowe Dr. Poway, CA 92064 • P: (858) 679-1191 • F: (858) 726-6005...
- Page 2 Dear Customer: Congratulations on the purchase of your new Prep Center S™. As technology continues to develop you can work confidently knowing that both Mytee Prod- ucts and its employees are equally dedicated to developing with the industry and its advances.
-
Page 3: Table Of Contents
Table of Contents Important Safety Information At a Glance 1.1 - Technical Specifications 1.2 - Included with the Prep Center S™ 1.3 - Prep Center S™ Features 1.4 - Prep Center S™ Switch Plate Machine Operation 2.1 - Powering the Prep Center S™ 2.2 - Connecting Vacuum and Solution Hoses 2.3 - Connecting Shop Air Line 2.4 - Filling the Solution Tank... -
Page 4: Important Safety Information
When and if calling Mytee for support, please grounding plug. The plug must be plugged into an appro- have your Model and Serial Number available for faster priate outlet that is properly installed in accordance with assistance. - Page 5 Important Safety Information To reduce the risk of fire, electrical shock, or injury: 18. When cleaning and servicing the machine, local or na- 1. Read all instructions before using equipment. tional regulations may apply to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, 2.
-
Page 6: At A Glance
1 - At a Glance 1.1 - Technical Specifications 1.2 - Included with the Prep Center S™ Body Roto-molded polyethylene Tanks 12 gallon (approx.) Single 3-stage low amp, Vacuum 100 CFM, 130” water lift Diaphragm pump, 120 PSI, Pump 1.3 GPM 8100 Vac/Sol Hose 8400P Air Lite™... -
Page 7: Prep Center S™ Features
1 - At a Glance 1.3 - Prep Center S™ Features 1. Pegs for tool storage 10. 10” foam-filled rear wheels 2. Clear recovery tank lid 11. 25’ 12/3 power cord 3. Solution tank opening 12. Air line input fitting 4. -
Page 8: Prep Center S™ Switch Plate
1 - At a Glance 1.4 - Prep Center S™ Switch Plate 1. Vacuum switch 4. Solution connection fitting 2. Pump switch 5. Air line output fitting 3. Heater switch... -
Page 9: Machine Operation
2 - Machine Operation 2.1 - Powering the Prep Center S™ 2.4 - Filling the Solution Tank Faucet Fill To power the Prep Center S™, plug the power cord into a grounded 20 amp outlet. The solution tank can be filled from a standard faucet or ♦... -
Page 10: Hot Water Extraction With The Prep Center S
2 - Machine Operation 2.6 - Hot Water Extraction with the 2.8 - Using Auxiliary Chemical Bottles Prep Center S™ Put desired chemical in the bottle(s) to be used. Connect To avoid a vapor lock, follow this procedure when turning shop air to the air line input quick connect in the bottom on the machine for hot water extraction. -
Page 11: Troubleshooting
3 - Troubleshooting 3.1 - Vacuum Troubleshooting Vacuum blows water out the exhaust. Vacuum is not turning on. Possible Causes Solutions Possible Cause Solution Foam building up in the Use a defoaming solution recovery tank. in the recovery tank. Vacuum may not be getting Check the electrical con- power. - Page 12 Remove the check valve the leak. If there are no valve between the pump temporarily and check to leaks, run Mytee’s System and heater may hang up, see if the pump will flow Maintainer™ (Part # 3601) causing the flow of water to...
-
Page 13: Heater Troubleshooting
Check all electrical con- 140°F water. tion. nections, including power cord and harness. Heater has hard water Run Mytee System Main- tainer™ (Part # 3601) buildup inside, leading to Automatic sensor has Reset the manual sensor lost efficiency. through the machine regu-... -
Page 14: Available Accessories
4 - Available Accessories PC88 Interior Drying Tool G008 Piglet™ Filters - pack of 20 8400 4” Stainless Steel Upholstery Tool 8700 Stainless Steel Crevice Tool... - Page 15 Notes...
- Page 16 Mytee Products, Inc. 13655 Stowe Dr. Poway, CA 92064 www.mytee.com © 2019 Mytee Products, Inc. Printed in the USA...