Related Manuals for Mytee Prep Center S 80-120
Summary of Contents for Mytee Prep Center S 80-120
- Page 1 User Manual Prep Center S ™ Model: 80-120 REV. 6/7/21 13655 Stowe Dr. Poway, CA 92064 P: (858) 679-1191 F: (858) 726-6005 www.mytee.com...
- Page 2 Dear Customer: Congratulations on the purchase of your new Prep Center S. As technology continues to develop you can work confidently knowing that both Mytee and its employees are equally dedicated to developing with the industry and its advances. Like any other piece of machinery or technology, the Prep Center S also requires proper maintenance and care to keep the product working over extended use.
-
Page 3: Table Of Contents
Table of Contents Important Safety Information At a Glance 1.1 - Technical Specifications 1.2 - Included with the Prep Center S 1.3 - Prep Center S Features 1.4 - Prep Center S Switch Plate Machine Operation 2.1 - Powering the Prep Center S 2.2 - Connecting Vacuum and Solution Hoses 2.3 - Connecting Shop Air Line 2.4 - Filling the Solution Tank... -
Page 4: Important Safety Information
When and an equipment-grounding conductor and grounding plug. The if calling Mytee for support, please have your Model and Serial plug must be plugged into an appropriate outlet that is properly Number available for faster assistance. - Page 5 Important Safety Information To reduce the risk of fire, electrical shock, or injury: 1. Read all instructions before using equipment. 2. Use only as described in this manual. Use only manufactur- er’s recommended attachments. 3. Always unplug power cord from electrical outlet before attempting any adjustments or repairs.
-
Page 6: At A Glance
1 - At a Glance 1.1 - Technical Specifications 1.2 - Included with the Prep Center S Body Roto-molded polyethylene Tanks 12 gallon (approx.) Single 3-stage low amp, Vacuum 100 CFM, 130” water lift Pump Diaphragm pump, 120 PSI, 1.3 GPM 1200 watt heating system –... -
Page 7: Prep Center S Features
1 - At a Glance 1.3 - Prep Center S Features 1. Pegs for tool storage 10. 10” foam-filled rear wheels 2. Clear recovery tank lid 11. 25’ 12/3 power cord 3. Solution tank opening 12. Air line input fitting 4. -
Page 8: Prep Center S Switch Plate
1 - At a Glance 1.4 - Prep Center S Switch Plate 1. Vacuum switch 4. Solution connection fitting 2. Pump switch 5. Air line output fitting 3. Heater switch... -
Page 9: Machine Operation
2 - Machine Operation 2.1 - Powering the Prep Center S 2.4 - Filling the Solution Tank Faucet Fill To power the Prep Center S, plug the power cord into a ground- ♦ ed 20 amp outlet. The solution tank can be filled 2.2 - Connecting Vacuum and Solution Hoses from a standard faucet or hose bib. -
Page 10: Using The Blower Attachment
2 - Machine Operation 1. Turn PUMP switch on. Pull the lever on the cleaning tool to Put desired chemical in the bottle(s) to be used. Connect shop release air in the line. Hold lever until a steady flow of water air to the air line input quick connect in the bottom right corner comes out of the tool. -
Page 11: Machine Maintenance
This filter should be checked after ♦ each use. 3.3 - System Maintainer Regular flushing of the solution system with Mytee System Maintainer keeps your extractor running efficiently by removing hard water scaling that builds up in the system. -
Page 12: Available Accessories
4 - Available Accessories PC88 Interior Drying Tool G008 Piglet™ Filters - pack of 20 8400 4” Stainless Steel Upholstery Tool 8700 Stainless Steel Crevice Tool... -
Page 13: Troubleshooting
Circuit breaker tripped in building. Reset breaker in building. turning on. Faulty switch or power cord. Contact a Mytee Service Center. Unclog the jet by removing and soaking in a vinegar Jet is clogged. and water solution. Scrub with a soft brush. Repeat if Poor solution flow. - Page 14 Mytee, LLC 13655 Stowe Dr. Poway, CA 92064 www.mytee.com © 2021 Mytee, LLC...