Panasonic AK-HRP1000G Operating Instructions Manual page 112

Item Setting value
USER ASSIGN GAIN
M.GAMM
H.CHRM
U.CHRM
DRS
KNEE.S
UHD S.DTL
HD S.DTL
S.HUE
S.TONE
IRIS LEV MODE ABS
RLTV
CAM SEL CAM1 to CAM99
DTL VOL UHD
HD
SD
SKIN DTL SW UHD
HD
SD
LCD BRIGHT 1 to 20
PANEL LED BRIGHT 1 to 5
7SEG BRIGHT 0 to 15
GROUP1
7SEG BRIGHT 0 to 15
GROUP2
BUZZER OFF
ON
PERIOD 0 to 5
CYCLE 0.3
0.5
1.0
STD POSITION -6 to 0 to +36
M.GAIN
STD POSITION VAR -2.9 to 0.0 to +2.9
STD POSITION ND 1 to 2 to 5
STD POSITION CC A to E
IRIS PRIORITY NON
Serial
LAN
Sets the function to assign to [USER] of the [SELECT] dial.
The setting values represent the following functions.
GAIN : GAIN (operates the R, G, and B gain values simultaneously. This value will be
"0" when auto white balance adjustment is performed. The value will also be "0" when
the function assigned to USER ASSIGN has been changed to something besides
"GAIN", or when switching to another camera.)
M.GAMM : MASTER GAMMA
H.CHRM : HD CHROMA GAIN
U.CHRM : UHD CHROMA GAIN
DRS: DRS
KNEE.S : KNEE SLOPE
UHD S.DTL : UHD SKIN DTL
HD S.DTL : HD SKIN DTL
S.HUE : SKIN CORRECTION(HUE)
S.TONE : SKIN CORRECTION(TONE)
Selects between absolute values or relative values to be used for IRIS control oper-
ations.
ABS: Absolute value control.
RLTV: Relative value control.
Switches between connected cameras.
Selects the target of detail control operations on the panel.
UHD: Control UHD detail.
HD: Control HD detail.
SD: Control SD detail.
Selects the target of skin tone detail control operations on the panel.
UHD: Control UHD skin tone detail.
HD: Control HD skin tone detail.
SD: Control SD skin tone detail. (Enabled when [CONNECT SETTING] is set to "Serial
(AK)" or "LAN(AK)".)
Sets the brightness of the LCD panel.
Set the brightness of the panel buttons.
Sets the brightness of the panel's 7-segment display (group 1).
This applies to the ND filter display, CC filter display, master gain display, and shutter
display.
Sets the brightness of the panel's 7-segment display (group 2).
This applies to the iris display and camera selection number / master pedestal display.
Enable or disable the buzzer (beep/call tone).
[PERIOD] and [CYCLE] will be the time from which [CALL] was released for [CAMERA
CCU].
PERIOD: Flashing duration (sec).
CYCLE: Flashing cycle (For 1.0: 500 msec off → 500 msec lit (repeatedly)).
Sets the standard position of the master gain (M.GAIN).
Sets the standard position of the master gain (M.GAIN) step value.
Sets the standard position of the ND filter.
Sets the standard position of the CC filter.
Sets whether to prioritize iris control.
NON
Does not prioritize iris control.
If the camera's iris position does not match the ROP's [IRIS] lever position, match
the ROP's [IRIS] lever position to the camera's iris position.
Serial
If the camera's iris position does not match the ROP's [IRIS] lever position, the
ROP's [IRIS] lever position during serial connection will be the basis of operation.
LAN
If the camera's iris position does not match the ROP's [IRIS] lever position, the
ROP's [IRIS] lever position during IP connection will be the basis of operation.
When multiple ROPs are IP connected to a single camera and the [IRIS
PRIORITY] setting for each ROP is set to "LAN", be aware that iris controls from
all of the ROPs will be performed directly.
- 112 -
Setting details
ROP menu