Page 1
BILLY GOAT KV VACUUM Accessories ON BOARD FELT DEBRIS VACUUM HOSE KIT 4"(102mm) x For use in 7' (2.13m) leaves and grass in dusty vacuuming in conditions. hard to reach areas. P/N 891125 P/N 891126 Part No 891058 KVSP/TKVSP Owner’s Manual...
ABOUT THIS MANUAL THANK YOU for purchasing a BILLY GOAT manufactured to provide years of reliable and productive service. This manual provides complete operating and maintenance instructions that will help to maintain your machine in top running order. Read this manual carefully before assembling, operating, or servicing your equipment.
0.58 qt (0.54L) #132 (58.9 kg) 141# (64 kg) 59” (1.5m) 59” (1.5 m) 25.5” (.6 m) 25.5” (.6 m) 42.75” (1.1m) 42.75” (1.1 m) 109 dBa 112 dBa 89 dBa 91 dBa 0.32 g (3.16m/s 0.43 g (4.25m/s Form No F042508A...
This symbol indicates that this manual and the engine manufacturer’s manual should be read carefully before assembling, operation, or servicing this equipment. This symbol indicates important information that will prevent damage to your BILLY GOAT KV Vacuum. This symbol indicates the engine oil level should be checked before operating this equipment.
Page 5
Remove all rocks, wire, string, plastic, etc. that can present a hazard during work prior to starting. DO identify and mark all fixed objects to be avoided during work such as sprinkler heads, water valves, buried cables, or clothes line anchors, etc. Part No 891058 Form No F042508A...
KVSP/TKVSP Owner’s Manual SOUND LEVEL 92 dB(a) at Operator Position VIBRATION LEVEL 0.34g (3.29m/s Sunny F (31.1 2 mph (3.8 kmh) South South East 30.07”Hg (764 mm Hg Sunny F (10 4 mph (6.4kph) South Southeast 30 Hg (101.6kpa Form No F042508A...
INSTRUCTION LABELS The labels shown below were installed on your BILLY GOAT this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The correct position for each label may be determined by referring to the Figure and Item numbers shown.
PACKING CHECKLIST Your Billy Goat KV Vacuum is shipped from the factory in one carton, completely assembled except for the upper handle, debris bag, and bag quick disconnect. READ all safety instructions before assembling unit. TAKE CAUTION when removing the unit from the box the Handle Assembly is attached by...
Drain fuel outdoors, into an approved container, away from open flame. Be sure engine is cool. Do not smoke. Run engine until fuel tank is empty and engine runs out of gasoline. Part No 891058 KVSP/TKVSP Owner’s Manual Form No F042508A...
Page 10
• Pressure-wash debris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry before use. NOTE: Having one or more spare debris bags is a good way to reduce down time while dirty bags are being cleaned. DO NOT leave debris in bag while in storage. Part No 891058 Form No F042508A...
Page 11
Before turning machine off, use the Tamper to slowly push remaining pieces of wood through the chipper. This can prevent any remaining wood from jamming in the chipper when machine is turned off. Do not leave tamper on the ground, store tamper in the chipper hopper. Part No 891058 Form No F042508A...
8. Lift impeller upward. If impeller slides freely, proceed to (step 10). 9. If the impeller does not loosen, obtain a 3/4-16x3” (Billy Goat part #440192) or longer bolt. Thread bolt by hand into nut until bolt rests against the shaft. Tighten the bolt slowly, which will pull the impeller away from the shaft, remove impeller from shaft.
Page 13
8. Lift impeller upward. If impeller slides freely, proceed to (step 10). 9. If the impeller does not loosen, obtain a 3/4-16x3” (Billy Goat part #440192) or longer bolt. Thread bolt by hand into nut until bolt rests against the shaft. Tighten the bolt slowly, which will pull the impeller away from the shaft, remove impeller from shaft.
Page 14
Note: The chipper blade gap is factory set and should be checked each time impeller is removed from engine crankshaft and reset if required. If reassembly requires a different quantity of shim washers, Billy Goat® shim washer must be used.
KVSP/TKVSP Owner’s Manual MAINTENANCE RECORD Date Service Performed Part No 891058 Form No F042508A...
Page 19
BRUSH CUTTER FORCE BLOWER AERATOR If you liked this product please feel free to view our full line of quality lawn care, renovation, and debris removal products at www.billygoat.com DL VACUUM MULTI VACUUM POWER RAKE Part No 891058 Form No F042508A...
Page 20
KVSP/TKVSP Owner’s Manual Part No 891058 Form No F042508A...