Connecting Optional Equipment; Listening To External Sources; Video/Aux Jacks; Sub Woofer Jack - Aiwa CX-NMT720 Operating Instructions Manual

OUT
Refer to the operating instructions of the connected equipment
for details.
The connecting cords are not supplied. Obtain the necessary
connecting cords.
Consult your local Aiwa dealer for optional equipment.
This unit can input analog sound signals through these jacks.
Use a cable with RCA phono plugs to connect audio equipment
(DVD player, turntables, LD players, MD players, VCRs, TV, etc.).
Connect the red plug to VIDEO/AUX R jack, and the white plug
to VIDEO/AUX L jack.
When connecting a turntable
Use an Aiwa turntable equipped with a built-in equalizer amplifier.
.,,., =*,*,
,g*g**3,,&Qq*%,% M4,m,
w\,#*m~**,,,*:~ :,%~,~..,.
b,.* ,,, . . .
..)w..wm,.m.,,& .bT*b~,w@@*@,,. h,.h, ,3,ga*>% .x= .,
,""
-.% . . . s..,<. ,...,...
MD JACKS
This jack is recommended to connect with an MD player.
Use a cable with RCA phono plugs.
Connect the red plug to MD R jack, and the white plug to MD L
jack.
,..+, .,,. . . .. .!......4.. ).. ~,.,,.:,% ",.*, .<,.,. *.,.,b, m,.,. i,,.,. , *.. . " . . . .,.....
--A,,-,,, . .,.,m #m. ... .... .. ", --- "- ~"~ '""~'"' - - "->- - *P r J,.-:!,",!?-
"."
, , -.,..,,.,& ...........
LINE OUT JACKS
This unit can output analog sound signal through these jacks,
Use a cable with RCA phono plugs to connect audio equipment
with LINE IN (analog input) jacks.
Connect the red plug of a cable to LINE OUT R jack, and the
white plug to LINE
OUT
L jack.
m
Do not connect an equipment to LINE OUT jacks and VIDEO/
AUX jacks simultaneously, Otherwise, noise is generated and
malfunction occurs.
This unit can output CD digital sound signals through this jack.
Use an optical cable to connect digital audio equipment (DAT
deck, MD recorder, etc.),
Remove the dust cap @ from CD DIGITAL OUT (OPTICAL)
jack. Then, connect an optical cable plug to CD DIGITAL OUT
(OPTICAL) jack.
Connect an optional powered sub woofer with built-in-amplifier
to the jack.
g<,:,:$~g=:~~$j,,-=:,;;.s g"%..: !~=!.{.w4,,.**@ a,*&r&,*-As*sw.%
P_.!*
w&Ywa
,Wr...s>m-. .,. +.._
,.t..!-Hww-#sma,4 **,g~*~*~,x
5.1 CH INPUT JACKS
This unit can input sound signals from the audio equipment (DVD
player, LD player, etc.) that contains a Dolby Digital decoder
with the 5.1 ch output terminals. Refer to "CONNECTING A DVD
PLAYER on page 28,
POWER
To play a equipment connected to VI DEO/AUX jacks or MD jacks
proceed as follows.
1 Press VIDEO/AUX/5.l CH or MD.
To play the eaui~ment connected to VIDEO/AUX, press
VIDEO/AUX/5.l CH. "VIDEO appears on the display.
To play the equipment connected to MD, press MD. "MD"
appears on the display.
2
Play the connected equipment.
To
change a source name
in the display
When VIDEO/ALfX/5.l CH is pressed, "VIDEO is displayed
initially. It can be changed to "AUX or "TV.
With the power on, press POWER while pressing l/[ DEO/Al.fx/
5.1 CH.
Repeat the procedure to select one of the names.
To adjust the sound level of the external source
When the sound level of the external source is much higher or
much lower than that of other function sources, adjust it as
follows.
1
Press VIDEO/AUX/5.l CH or MD and play the equipment.
2 Press + or -so that the sound level becomes the same
as that of other function sources.
m
During recording, the sound level can not be adjusted.
When CD DIGITAL OUT (OPTICAL) jack is not being
used
Attach the supplied dust cap.
27
ENGLISH