Table of Contents
Advertisement
Parameters
8-17 Configurable Alarm and Warningword
The configurable alarm and warning word has 16 bits (0-15).
Each of those bits can be configured to any of the following
options.
Option:
[8]
DC undervoltage warning
[9]
Inverter overloaded warning
[10]
Motor ETR overtemp warning
[11]
Motor thermistor overtemp warning
[12]
Torque limit warning
[13]
Over current warning
[14]
Earth fault warning
[17]
Controlword timeout warning
[19]
Discharge temp high warning
[22]
Hoist mech brake warning
[23]
Internal fans warning
[24]
External fans warning
[25]
Brake resistor short circuit warning
[26]
Brake powerlimit warning
[27]
Brake chopper short circuit warning
[28]
Brake check warning
[29]
Heatsink temperature warning
[30]
Motor phase U warning
[31]
Motor phase V warning
[32]
Motor phase W warning
[34]
Fieldbus communication warning
[36]
Mains failure warning
[40]
T27 overload warning
[41]
T29 overload warning
[45]
Earth fault 2 warning
[47]
24V supply low warning
[58]
AMA internal fault warning
[59]
Current limit warning
[60]
External interlock warning
[61]
Feedback error warning
[62]
Frequency max warning
[64]
Voltage limit warning
[65]
Controlboard overtemp warning
[66]
Heatsink temp low warning
[68]
Safe stop warning
[73]
Safe stop autorestart warning
[76]
Power unit setup warning
[77]
Reduced powermode warning
[78]
Tracking error warning
[89]
Mech brake sliding warning
[163]
ATEX ETR cur limit warning
[165]
ATEX ETR freq limit warning
[10002]
Live zero error alarm
[10004]
Mains phase loss alarm
[10007]
DC overvoltage alarm
[10008]
DC undervoltage alarm
[10009]
Inverter overload alarm
[10010]
ETR overtemperature alarm
[10011]
Thermistor overtemp alarm
MG92G102
Programming Guide
8-17 Configurable Alarm and Warningword
The configurable alarm and warning word has 16 bits (0-15).
Each of those bits can be configured to any of the following
options.
Function:
Option:
[10012]
[10013]
[10014]
[10016]
[10017]
[10022]
[10026]
[10027]
[10028]
[10029]
[10030]
[10031]
[10032]
[10033]
[10034]
[10036]
[10037]
[10038]
[10039]
[10045]
[10046]
[10047]
[10048]
[10049]
[10060]
[10061]
[10063]
[10065]
[10067]
[10068]
[10069]
[10073]
[10074]
[10075]
[10078]
[10079]
[10081]
[10082]
[10084]
[10090]
[10091]
[10164]
[10166]
Danfoss A/S © 06/2015 All rights reserved.
Torque limit alarm
Overcurrent alarm
Earth fault alarm
Short circuit alarm
CTW timeout alarm
Hoist brake alarm
Brake powerlimit alarm
Brakechopper shortcircuit alarm
Brake check alarm
Heatsink temp alarm
Phase U missing alarm
Phase V missing alarm
Phase W missing alarm
Inrush fault alarm
Fieldbus com faul alarm
Mains failure alarm
Phase imbalance alarm
Internal fault
Heatsink sensor alarm
Earth fault 2 alarm
Powercard supply alarm
24V supply low alarm
1.8V supply low alarm
Speed limit alarm
Ext interlock alarm
Feedback error alarm
Mech brake low alarm
Controlboard overtemp alarm
Option config changed alarm
Safe stop alarm
Powercard temp alarm
Safestop auto restart alarm
PTC thermistor alarm
Illegal profile alarm
Tracking error alarm
Illegal PS config alarm
CSIV corrupt alarm
CSIV param error alarm
No safety option alarm
Feedback monitor alarm
AI54 settings alarm
ATEX ETR current lim alarm
ATEX ETR freq limit alarm
Function:
6
6
31
Advertisement
Table of Contents
Troubleshooting
