Self-Rearming; Sleep Mode - Energy Saver Feature; Hazard Warning Flashers - Gemini 953N User's And Installer's Manual

4.5 - ANTI-HIJACK FEATURE
To activate the anti-hijack feature while the engine is running, either:
!
Press remote control button "1".
!
Press remote control button "2".
!
!
Press the anti-hijack button (if installed).
The LED will turn ON steady and the turn indicators will flash twice to confirm
the anti-hijack feature has been activated.
20 sec. after the anti-hijack feature has been activated, the siren will sound for
approx. 1 min. while the turn indicators will flash until the anti-hijack mode is
deactivated. The system will kill the engine 2 sec. after the siren is triggered.
To exit the anti-hijack mode:
!
Press the anti-hijack button for 2 sec. (if installed).
!
Enter the PIN code.
To exit the anti-hijack mode via PIN code proceed as follows:
!
Wait for the siren to stop wailing.
!
If ignition key is in the ON position, turn it OFF.
!
If key is in the OFF position, cycle it ON and OFF.
!
After 4 sec. there will be a sequence of 9 LED flashes.
!
From this point on, proceed as indicated in par. 7.0 and 8.0.
!
Disarming via PIN code will be confirmed by 3 Beep and 3 flashes of the
turn indicators.
The anti-hijack mode has a memory feature.
I f the power supply is disconnected and subsequently
reconnected an alarm will be triggered because
considered a theft attempt.
4.6 - PRE-ALARM MODE
If the pre-alarm feature is enabled, the siren, during an alarm condition (ex.
tilt), will start sounding for approx. 2.5 sec. for the first 3 cycles, then from the
4th cycle on, it will sound for 30 sec. Alarm cycles will be reset every time the
alarm is disarmed or whenever the panic alarm is activated.

4.7 - SELF-REARMING

When the system is armed and then accidentally disarmed, the system will
automatically rearm 35 sec. after it has been unintentionally disarmed.
PAGE 9

5.0 - SLEEP MODE - ENERGY SAVER FEATURE

In order to preserve battery life, the system will automatically revert to sleep
mode when the vehicle is sitting idle for a period of time.
IF THE SYSTEM IS DISARMED
The system will go into sleep mode, 72h after it has been disarmed or engine
has been switched OFF. Remote controls will be inoperative during sleep
mode: normal operation is
To manually activate this feature before 72h, proceed as follows:
!
Turn ignition key in "ON"; the LED will light up for approx. 1 sec.
! Within 4 sec. of the LED flash, simultaneously press both remote control
buttons; 1 Beep will confirm the system has entered sleep mode
!
Turn ignition key "OFF".
!
To wake up the system, cycle ignition key "ON" and "OFF".
IF THE SYSTEM IS ARMED
The system will
armed. All protection features are operative during sleep mode except the
status LED.
Remote controls are inoperative, normal operation is restored when ignition is
switched ON.
When the engine is switched ON, there is a 5 sec. delay to allow disarming
without triggering the siren.
it will be To make the turn indicators flash as Hazard warning lights, proceed as
follows:
With the system disarmed, turn ignition key in "ON"; the LED will light up for
approx. 1 sec.
!
While the LED is ON, press remote control button "1".
!
Turn ignition key "OFF"; the turn indicators will start flashing.
!
To disable the flashers, turn ignition key "ON" (and eventually "OFF") or
arm the system.
:
automatically restored upon turning ignition ON.
:
automatically go into sleep mode 72h after it has been

6.0 - HAZARD WARNING FLASHERS

.
PAGE 10