Parameters For Data Sets; Parameters For Command Data Sets (Cds) - Siemens SINAMICS G List Manual

Parameters

Parameters for data sets

1.3 Parameters for data sets
1.3.1

Parameters for Command Data Sets (CDS)

Note:
References: /IH1/
The following list contains those parameters which are dependent on Command Data Sets.
Product: SINAMICS G, Version: V02.20.28.00, Label: ARM_M0475_11, Language: en
p0700[0...n]
p0820[0...n]
p0821[0...n]
p0822[0...n]
p0823[0...n]
p0824[0...n]
p0840[0...n]
p0844[0...n]
p0845[0...n]
p0848[0...n]
p0849[0...n]
p0852[0...n]
p0854[0...n]
p0855[0...n]
p0856[0...n]
p1000[0...n]
p1020[0...n]
p1021[0...n]
p1022[0...n]
p1023[0...n]
p1035[0...n]
p1036[0...n]
p1039[0...n]
p1041[0...n]
p1042[0...n]
p1043[0...n]
p1044[0...n]
p1055[0...n]
p1056[0...n]
p1070[0...n]
p1071[0...n]
p1075[0...n]
p1076[0...n]
p1085[0...n]
p1088[0...n]
p1110[0...n]
p1111[0...n]
p1113[0...n]
1-362
SINAMICS S120 Commissioning Manual
in section "Data Sets"
Macro binector input (BI) / Macro BI
BI: Drive data set selection DDS bit 0 / DDS select., bit 0
BI: Drive data set selection DDS bit 1 / DDS select., bit 1
BI: Drive data set selection DDS bit 2 / DDS select., bit 2
BI: Drive data set selection DDS bit 3 / DDS select., bit 3
BI: Drive data set selection DDS bit 4 / DDS select., bit 4
BI: ON/OFF1 / ON/OFF1
BI: 1. OFF2 / 1. OFF2
BI: 2. OFF2 / 2. OFF2
BI: 1. OFF3 / 1. OFF3
BI: 2. OFF3 / 2. OFF3
BI: Enable operation / Enable operation
BI: Master ctrl by PLC / Master ctrl by PLC
BI: Unconditionally release holding brake / Uncond. open brake
BI: Enable speed controller / Enable n_ctrl
Macro connector inputs (CI) for speed setpoints / Macro CI n_set
BI: Fixed speed setpoint selection Bit 0 / n_set_fixed Bit 0
BI: Fixed speed setpoint selection Bit 1 / n_set_fixed Bit 1
BI: Fixed speed setpoint selection Bit 2 / n_set_fixed Bit 2
BI: Fixed speed setpoint selection Bit 3 / n_set_fixed Bit 3
BI: Motorized potentiometer, setpoint, raise / Mop raise
BI: Motorized potentiometer, lower setpoint / Mop lower
BI: Motorized potentiometer, inversion / Mop inversion
BI: Motorized potentiometer, manual/automatic / Mop manual/auto
CI: Motorized potentiometer, automatic setpoint / Mop auto setpoint
BI: Motorized potentiometer, accept setpoint / Mop accept set val
CI: Motorized potentiometer, setting value / Mop setting value
BI: Jog bit 0 / Jog bit 0
BI: Jog bit 1 / Jog bit 1
CI: Main setpoint / Main setpoint
CI: Main setpoint scaling / Main setpt scal
CI: Suppl setpoint / Suppl setpoint
CI: Supplementary setpoint scaling / Suppl setpt scal
CI: Speed limit in positive direction of rotation / n_limit pos
CI: Speed limit negative direction of rotation / n_limit neg
BI: Inhibit negative direction / Inhibit negative
BI: Inhibit positive direction / Inhibit positive
BI: Direction reversal / Direction reversal
 Siemens AG 2004 All Rights Reserved
SINAMICS G List Manual, Edition 12.2004