Bertazzoni X365GGVX (X36 5 00 X) Installation And User Instructions Manual
Bertazzoni X365GGVX (X36 5 00 X) Installation And User Instructions Manual

Bertazzoni X365GGVX (X36 5 00 X) Installation And User Instructions Manual

Freestanding gas ranges
Hide thumbs Also See for X365GGVX (X36 5 00 X):

Advertisement

DIMENSIONS: 36'' (915 mm)(W) x 253/16'' (640 mm)(D) x36'' (915 mm)(H)
Models X365GGVX (X36 5 00 X) [M3W0GTU4X(2 or 5)A]
Models X366GGVX (X36 6 00 X) [M3Y0GTU4X(2 or 5)A]
IMPORTANT - PLEASE READ AND FOLLOW
-Before beginning installation, please read these instructions completely and carefully.
-Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. -Please observe all local
and national codes and ordinances.
-Please ensure that this product is properly grounded.
-The installer should leave these instructions with the consumer who should retain for local inspector's use and for
future reference.
-The electrical plug should always be accessible.
Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1-latest edition. Electrical
installation must be in accordance with the National Electrical Code, ANIS/NFPA70
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas Installation Code or CAN/CGA-B
Installation Code and/or local codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical
Codes Part 1 and/or local codes.
Installation of any gas-fired equipment should be made by a licensed plumber. A manual gas shut-off valve must be installed in the gas
supply line ahead of the oven in the gas flow for safety and ease of service.
In Massachusetts:
All gas products must be installed by a "Massachusetts" licensed plumber or gasfitter. A "T" handle type manual
gas valve must be installed in the gas supply line to this appliance.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
OBSERVE ALL GOVERNING CODES AND ORDINANCES.
WARNING: If the information in this manual is not followed exactly, a
fire or explosion may result causing property damage, personal injury
or death.
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

- Do not light any appliance.
- Do not touch any electrical switch.
- Do not use any phone in your building.
- Immediately call your gas supplier from a neighbor's phone. Follow
the gas supplier's instructions.
- If you cannot reach your gas suppliers, call the fire department.
Installation and service must be performed by a qualified installer,
service agency or the gas supplier.
310199
Installation, Service and User Instructions
FREESTANDING GAS RANGES
BERTAZZONI
Warning!
- This range can tip. Injury to persons could result.
- Install anti-tip device shipped with range.
-See Installation Instructions
-
latest edition and/or local codes. IN CANADA:
149.2,
Propane

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X365GGVX (X36 5 00 X) and is the answer not in the manual?

Questions and answers

Summary of Contents for Bertazzoni X365GGVX (X36 5 00 X)

  • Page 1: What To Do If You Smell Gas

    310199 FREESTANDING GAS RANGES BERTAZZONI Warning! - This range can tip. Injury to persons could result. - Install anti-tip device shipped with range. -See Installation Instructions latest edition and/or local codes. IN CANADA: 149.2,...
  • Page 2: Installation Instructions

    WARNING Read this instruction booklet before installing and using the appliance. The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance. The manufacturer reserves the right to make changes to its products when considered necessary and useful, without affecting the essential safety and operating characteristics.
  • Page 3 3. Position the two anti-tip brackets on the wall at the measured dimension plus 1/8" (0.32 cm). The brackets have to be placed at 2”5/16 (6,0 cm) from the side of the range. The distance between the two bracket is 31”1/4 (79,3 cm) clearance.
  • Page 4: Backguard Installation Instruction

    BACKGUARD INSTALLATION INSTRUCTION Remove n°2 screws fixing worktop as shown in fig.1 Place front part of the backguard and attach it from bottom side with the two removed screws (point 2) as shown in fig .2 Fix the front part of the backguard with the screws supplied with the backguard kit (fig.3) Assemble back part with front part of the backguard and fix them with a screws supplied with the backguard kit (fig.4) WORKTOP FRONTGUARD INSTALLATION INSTRUCTIONS...
  • Page 5 INSTALLATION SIDE-BY-SIDE TO KITCHEN CABINET 1. This range may be installed directly adjacent to existing 36" (91.5 cm) high cabinets. IMPORTANT: The top border of the worktop should be at the same level of the adjacent accomplished by raising the unit using the adjustment spindles on the legs.
  • Page 6: Electrical Connection

    COOKER HOOD INSTALLATION The bottom of the hood should be 25 typically result in the bottom of the hood being 61 for other minimum clearance requirements mandated by specific local or regional installation codes. Refer to the rangehood installation instructions for additional information. These dimensions provide for safe and efficient operation of the hood.
  • Page 7 Wiring diagram For freestanding gas range model X366GGVX (X36 6 00 X) CAUTION: label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. For freestanding gas range model X365GGVX (X36 5 00 X) CAUTION: label all wires prior to disconnection when servicing controls.
  • Page 8: Gas Connection

    All gas connections must be made according to national and local codes. The gas supply (service) line must be the same size or greater than the inlet line of the appliance. This range uses a 1/2" NPT inlet (see fig. in this chapter for details of gas connections installations).On all pipe joints use sealant resistant to LP gas.
  • Page 9: Final Preparation

    shut-off valve and regulator, use agency-approved, properly sized flexible or rigid pipe. Check all local code requirements. PERFORMANCE CHECKLlST All burners are tested before leaving the factory. There are no adjustments for the burners if connected according to the information on the rating plate. Check each burner for proper operations. Flames should be blue in all settings. If service is required, contact your dealer for the name of their authorized service agency.
  • Page 10 - CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS: To change the nozzles of the burners use the following procedure: Lift up the burners and unscrew the nozzles ( Fig.) using an adjustable spanner of 7 mm and change the nozzles with those designed for the new gas supply according to the information given in TABLE shown below.
  • Page 11: Adapting To Different Types Of Gas

    Models X366GGVX (X36 6 00 X) [M3Y0GTU4X(2 or 5)A] Adapting to different types of gas Burner Position Injector diam. [mm.] Auxiliary Front R 0,90 0,54 Semi-Rapid Rear L & C 1,18 Front C 0,70 Rapid Rear L 1,55 0,92 Front L Inner 0,80 Dual Burner 0,49...
  • Page 12: Service & Maintenance Instructions

    Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum: 1) Light the burner and set the knob to the MINIMUM position (small flame). 2) Remove the knob of the valve that is press fit on the rod of that valve. 3) The cooker is equipped with safety valves, use a small slotted screwdriver the choke valve located on the valve body and turn the choke screw to the right or left until the burner flame is adjusted to minimum 4) Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position.
  • Page 13: Control Panel Description

    USER MANUAL WARNINGS: Keeping appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquid. Do not store dangerous or flammable material in the cabinet areas above appliance; store them in a safe place in order to avoid potential hazards. For safe use of appliance, do not use it for space heating.
  • Page 14: Using Burners

    USING BURNERS A diagram is etched on the control panel above each knob which indicates which burner corresponds to that knob. Manual ignition: Manual ignition is always possible even when the power is cut off or in the event of prolonged power failure. Turn the knob that corresponds to the burner selected counterclockwise to the MAXIMUM position at the etched star (large flame) and place a lit match up to the burner.
  • Page 15: Using The Gas Oven

    USING THE GAS OVEN All the gas oven cookers are equipped with a thermostat and safety device to adjust the cooking temperature. The oven temperature is set by turning the knob counterclockwise to match the indicator with the temperature selected. The gas oven is combined with a gas broiler.
  • Page 16 The convection system partially changes the various notions about traditional cooking. Meat no longer needs to be turned while it is cooking and the rotisserie is no longer needed to cook a roast on the spit. Just put the meat directly on the shelf.
  • Page 17: Cleaning The Appliance

    Intensive and continuous use of the appliance may require additional ventilation, for example by opening a window, or increasing the power of the mechanical exhaust fan/range hood, if installed. Note: the cooker is equipped with the cooling fan that starts operation each time the oven knob is on a position different from 0 (zero).
  • Page 18: After-Sale Service

    Please note here below details for after save service. Refer to warranty certificate for warranty condiftions Dealer /Importer: Name, address, phone SERVICE CENTERS Name Phone MANUFACTURER: BERTAZZONI SPA VIA PALAZZINA, 8 – 42016 – GUASTALLA (REGGIO E.) ITALY Tel. 0522/226411 – telefax 0522/226440 – http://www.bertazzoni-italia.com...
  • Page 19: Spare Part List

    Number Drawing Code Description 601736 CIRCUIT DIAGRAM 202317 PART FOR BURNER FIXING 202386 PART FOR DUAL WOK AND SEMI RAPID BURNERS 510507 SMALL BURNER 510508 SEMI RAPID BURNER 510509 RAPID BURNER 510511 DUAL BURNER 504128 SMALL FLAME SPREADER 504129 MEDIUM FLAME SPREADER 504130 RAPID FLAME SPREADER 504189 ULTRA RAPID FLAME SPREADER 504160 COVER FOR SMALL FLAME SPREADER...
  • Page 20 410558 FLAP DOOR 504163 OVEN BURNER +BAFFLE+ SPARK PLUG +THERMOC 505013 SUPPORT FOR BROILER BURNER NOZZLE 508021 TERMOCOUPLE MM600 508025 TERMOCOUPLE MM300 508026 THERMOCOUPLE OVEN BURNER 508027 TERMOCOUPLE MM800 508032 TERMOCOUPLE FOR DUAL BURNER 603020 MOTOVENTILATOR 603019 COOLING FAN 602039 COMMUTATOR 608046 OVEN BULB WITH HOLDER 601991 TERMINAL SEPARATOR 608044 SMALL WARNING LIGHT...
  • Page 21 1622 608025 SMALL RED BUD 1622 608045 SMALL BLUE BUD 1624 200317 WORK TABLE 1624 200316 WORK TABLE 1627 501629 GAS COLLECTOR 1627 501628 GAS COLLECTOR 1628 501634 TUBE FOR RIGHT FRONT BURNER 1631 501635 TUBE FOR RIGHT BACK BURNER 1639 202390 LEFT VERTICAL VENT 1644...

Table of Contents

Save PDF