Gemini 953 Installation And Use Manual
Alarm system
Hide thumbs
Also See for 953:
- Installation and use manual (20 pages) ,
- Installation and use manual (17 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Related Manuals for Gemini 953
Summary of Contents for Gemini 953
- Page 1 INSTALLATION AND USE MANUAL GEMINI Technologies S.p.A. Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia Tel. +39 0332 943211 - Fax +39 0332 948080 www.gemini-alarm.com Made in Italy AC 2743/UK - Rev.04 - 05/13 ISO 9001 Certified Company...
-
Page 2: Table Of Contents
Dear Customer, Page - PRELIMINARY ADVICE............Page 2 Thank you for choosing this Gemini 953 alarm system designed and - USE AND MAINTENANCE............manufactured in Italy specifically for two-wheeled vehicles. USER MANUAL The present manual includes information for all options available, you may Page 3 therefore find that some of the information does not apply. -
Page 3: User Manual
USER MANUAL Electronic Key Receptacle Positioning 3.0 - ALARM SYSTEM CONTROL DEVICES Electronic key The remote controls and electronic key are used to operate the alarm system. A PIN-CODE can also be used to emergency override the system should the remote control be lost or inoperative. -
Page 4: Motion Sensor Exclusion
4.5 - MOTION SENSOR EXCLUSION 4.10 - SYSTEM DISARMING WITHOUT ALARM MEMORY The alarm built-in sensor to detect tilt, motion or a sudden shock can be Press remote control button 1 or insert the electronic key in its receptacle to excluded during the first 4”... -
Page 5: Acoustic And Optic Signals
5.1 - ACOUSTIC AND OPTICAL SIGNALS The system will cause the motorcycle engine to be cut off 20” after activation. Two seconds later the siren will go off continuously for 1 minute and the turn Optical signals (turn indicators and status LED) and acoustic signals (siren) indicators will start blinking repeatedly until the anti-hijack is disabled. -
Page 6: Pin-Code Override
9.0 - PIN-CODE OVERRIDE EXAMPLE PIN-CODE OVERRIDE If you cannot disarm the system from the remote control or with the electronic To help you understand the override procedure by PIN-CODE, here below is a key (remotes are lost or broken or batteries are flat), you will be able to disarm step-by-step example entering PIN-CODE 2-3-4-1. -
Page 7: Pin-Code Customization
ress both buttons at the same time. 10.0 - PIN-CODE CUSTOMIZATION The LED will turn OFF. Here below is a step-by-step example showing how to customize the PIN- CODE. In this case the selected PIN-CODE is 2-3-4-1 Disarm the alarm system Ground the BROWN/GREEN wire. -
Page 8: Replacing Remote Control Batteries
Doc ref. No. 2010-01 The remote control operates using alkaline batteries. When the batteries are too weak, replace them as follows: We, the undersigned, Company GEMINI TECHNOLOGIES S.p.A Address, City Via Luigi Galvani 12, 21020 Bodio Lomnago (VA) Country Italy... -
Page 9: Caution
INSTALLER MANUAL 2.0 - ALARM UNIT POSITIONING CONTENTS Do not install the alarm unit in this position as water ingress over time - PRELIMINARY ADVICE............Page 15 may seep through the rubber sheath - ALARM UNIT POSITIONING..........Page 16 and permanently damage the - ALARM UNIT SEALING............ -
Page 10: Alarm Unit Sealing
3.0 - ALARM UNIT SEALING 4.0 - ACCESSORIES POSITIONING 4.1 - RECEPTACLE FOR ELECTRONIC KEY AND LED INDICATOR The receptacle with built-in LED (or the LED) must be installed where it can readily be seen and accessed by the user. The LED warning light serves as To seal the alarm, position the both a system status indicator and a visual theft deterrent rubber cap over the external edge... -
Page 11: Contact Switch (Optional)
6.0 - WIRING DIAGRAM 5.0 - ELECTRICAL CONNECTIONS CAUTION The tables below refer to the standard wiring harness (KITCA 417). For a complete list of model-specific wiring harnesses, please visit: www.gemini-alarm.com (private area). Pos. Wire colour Wire function - 1 -... -
Page 12: Engine Immobilization Connection Diagram (Ground Wire)
7.0 - ENGINE IMMOBILIZATION CONNECTION DIAGRAM 8.0 - ENGINE IMMOBILIZATION CONNECTION DIAGRAM ENGINE CUT-OFF by GROUND ING A WIRE ENGINE CUT-OFF by TING A WIRE For most small For most large two-stroke motorcycle engines four-stroke motorcycle engines White White White/Grey Grey Ground Ignition key... -
Page 13: Example Of Engine Immobilization Connection With Specific Wiring Harness
9.0 - EXAMPLE OF ENGINE IMMOBILIZATION CONNECTION 9.0 - EXAMPLE OF ENGINE IMMOBILIZATION CONNECTION WITH SPECIFIC WIRING HARNESS WITH SPECIFIC WIRING HARNESS Ignition key Plug the alarm Ignition key harness connector into the ignition switch connector Alarm unit Vehicle wiring harness before fitting the Plug the alarm specific wiring harness... -
Page 14: Electrical Connections With Specific Wiring Harness
10.0 - ELECTRICAL CONNECTIONS WITH SPECIFIC 11.0 - DIODE INSTALLATION WIRING HARNESS Check if a diode needs to be installed on the vehicle: After selecting the appropriate position for the alarm system and accessories Activate one of the turn indicators, turn ignition OFF and arm the alarm. (electronic key receptacle, seat/topcase contact switch), proceed with the If the instrument panel comes on when the turn indicators are activated, a electrical connections. -
Page 15: Learning New Devices (With Ground Wire)
12.0 - LEARNING NEW DEVICES 13.0 - LEARNING NEW DEVICES (With BROWN/GREEN WIRE GROUND CONNECTION) (Without BROWN/GREEN WIRE GROUND CONNECTION) The alarm is supplied with 2 remote controls and 1 electronic key but extra The alarm is supplied with 2 remote controls and 1 electronic key but extra optional devices can be added. -
Page 16: Programmable Features
GREEN/BROWN wire. Button N.1: ENABLE Remove from ground after ACOUSTIC SIGNALS programming. (enabled by Gemini) Button N.2: DISABLE Button N.1: ENABLE PANIC SIREN (enabled by Gemini) Button N.2: DISABLE Button N.1: ENABLE MOTION SENSOR Turn ignition key “ON”. -
Page 17: Programming Example
15.0 - PROGRAMMING EXAMPLE 16.0 - MOTION SENSOR ADJUSTEMENT To help you understand the programming procedure, here below is an The alarm system has a built-in shock sensor with 5 levels of sensitivity example showing how to activate the acoustic signals, the panic alarm, the adjustment.