Table of Contents
Advertisement
Quick Links
Alarm model:
...........................................................................
Sold on:
...........................................................................
By:
I nstalled on bike
model, number
GEMINI Technologies S.r.l.
Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italy
Tel. +39 0332 943211 - Fax +39 0332 948080
www.gemini-alarm.com
ISO 9001 Certified company
953NH
USER AND INSTALLER
MANUAL
UK
Made in Italy
REV.02 - 05/17
Advertisement
Table of Contents
Related Manuals for Gemini 953NH
Summary of Contents for Gemini 953NH
- Page 1 I nstalled on bike model, number 953NH USER AND INSTALLER MANUAL GEMINI Technologies S.r.l. Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italy Tel. +39 0332 943211 - Fax +39 0332 948080 www.gemini-alarm.com Made in Italy ISO 9001 Certified company...
-
Page 2: Table Of Contents
CONTENTS CONTENTS - INTRODUCTORY NOTE INSTALLER MANUAL USER MANUAL 15.0 FITTING INSTRUCTIONS - ALARM SYSTEM CONTROL DEVICES 16.0 - ALARM UNIT SEALING 2.1 - Transponder (RFID TAG) 17.0 - ALARM UNIT POSITIONING 2.2 - Remote control 18.0 - ACCESSORIES - FITTING - SYSTEM OPERATION - BASIC CONFIGURATION 18.1 - Status LED 3.1 - Arming... -
Page 3: Introductory Note
1.0 - INTRODUCTORY NOTE 2.1 - TRANSPONDER Dear customer, The transponder can only be used to disarm the alarm system. This self-powered alarm system, specifically designed and manufactured for 2- The transponder is not factory learned, it must be initially wheeled vehicles, is supplied with 1 transponder (RFID TAG) and 1 remote control. -
Page 4: System Operation - Basic Configuration
3.5 - ALARM EVENTS 3.0 - SYSTEM OPERATION - BASIC CONFIGURATION If an alarm event is detected during the armed state, the siren will sound, the 3.1 - ARMING LED will turn ON steady and the turn indicators will flash repeatedly for approx. If no TAG is detected when the engine is switched OFF the alarm system will 30 sec. -
Page 5: System Disarming Without Alarm Memory
3.10 - SYSTEM DISARMING WITHOUT ALARM MEMORY 4.0 - PROGRAMMABLE FEATURES If the TAG is detected when ignition is switched ON, t he system automatically The alarm system is factory preset with some of the features disabled as detailed below. disarms otherwise press remote control button “1”. -
Page 6: Passive Arming
4.4 - PASSIVE ARMING 4.6 - PRE-ALARM MODE Passive arming is factory enabled (see par. 3.1). Do not modify. If the pre-alarm feature is enabled, the siren, during an alarm condition , will start sounding for approx. 2.5 sec. for the first 3 cycles, then from the 4th cycle 4.5 - ANTI-HIJACK FEATURE on, it will sound for 30 sec. -
Page 7: Pin Code Override
7.0 - PIN CODE OVERRIDE 8.0 - PIN CODE OVERRIDE EXAMPLE If you cannot disarm the system from the remote control because it is lost or To help you understand the override procedure by PIN code, here below is a broken or batteries are flat, you will be able to disarm the system by using the step-by-step example entering PIN code “2-3-4-1”. -
Page 8: Pin Code Customization
9.0 - PIN CODE CUSTOMIZATION Simultaneously press both remote control buttons. The LED will turn OFF Here below is a step-by-step example showing how to customize the factory PIN code. In this case the selected PIN code is 2-3-4-1 isarm the alarm system Ground the BROWN-GREEN wire. -
Page 9: Remote Control
10.0 - REPLACING BATTERIES 10.2 - TRANSPONDER Proceed as follows to replace the battery: 10.1 - REMOTE CONTROL 1. Separate the plastic covers and remove the circuit with care. When the remote control batteries are too weak (see par. 2.2), replace them as follows: Separate the remote shells taking care not to damage the internal circuit. -
Page 10: Waste Electrical And Electronic Equipment (Weee) Directive
Consumers who need to enforce their statutory consumer guarantee rights ATTENTION against defective products - in accordance with Art. 128 et seq. of the Italian Gemini Technologies Gemini Technologies will not be held responsible for any damage will not be held responsible for any damage Consumer Sales Code (Leg. -
Page 11: Installer Manual
INSTALLER MANUAL 17.0 - ALARM UNIT POSITIONING Since the alarm system has a built-in high sensitivity triaxial tilt sensor, it can 15.0 - FITTING INSTRUCTIONS be positioned either vertically or horizontally as long as you keep the following in mind Please read all instructions and understand them thoroughly before starting the installation. -
Page 12: Status Led
18.0 - ACCESSORIES CAUTION Alarms are supplied without wiring harnesses. A wide range of specific pin- 18.1 - STATUS LED to-pin wiring harnesses is available for the most common motorbikes. Since the LED warning light serves as both a system status indicator and a The following tables refer to the generic wiring harness KITCA 417N17. -
Page 13: Wiring Diagram
20.0 - WIRING DIAGRAM 21.0 - IMMOBILIZER CONNECTIONS ENGINE IMMOBILIZER - GROUNDED WIRE For most small 2-stroke motorcycle engines. White White/Grey Ground Key switch Immobilizer wire Orange Turn indicators Orange To vehicle engine (12V) Status Seat/topcase ENGINE IMMOBILIZER - CUT WIRE contact switch (recommended) Green-Brown... -
Page 14: Diode Installation
22.0 - DIODE INSTALLATION Turn ignition key in ON. 2 flashes of the turn indicators and 2 confirmation tones (1 Bop and 1 Beep) How to tell if you need to install a diode: will acknowledge the system is in learn mode. Activate one of the turn indicators, turn ignition key OFF and arm the alarm. -
Page 15: Programmable Features
After pressing both buttons simultaneously (step 4), program the features 24.0 - PROGRAMMABLE FEATURES according to your needs. To either enable or disable one of the programmable features, proceed as follows: TO ENABLE TO DISABLE NB: Remember to ALWAYS arm/disarm the system before programming. Press button 1 Press button 2 Beep... -
Page 16: Programming Example
26.0 - TILT SENSOR ADJUSTMENT 25.0 - PROGRAMMING EXAMPLE Here below is a step-by-step example showing how to program the system The alarm system has a built-in triaxial tilt/shock sensor with 4 levels of with the tilt sensor and self-rearming disabled. sensitivity adjustment. - Page 17 R&TTE Declaration of Conformity NOTES Doc ref. No. 2010-01 We, the undersigned, Company GEMINI TECHNOLOGIES S.r.l Address, City Via Luigi Galvani 12, 21020 Bodio Lomnago (VA) Country Italy Phone number +39 0332 943211 Fax number +39 0332 948080 Declare under our sole responsibility that the following equipment:...