Related Manuals for Clarke KING150
Summary of Contents for Clarke KING150
- Page 1 WARNING: Do not use the hot washer without reading this manual HOT WASHER MODEL NO: KING150 PART NO: 7320175 OPERATION & MAINTENANCE INSTRUCTIONS LS1215...
- Page 2 This guarantee does not effect your statutory rights. LIST OF CONTENTS The following items should be supplied in the carton. If any parts are missing or damaged, please see your Clarke dealer where you purchased the hot washer 1 x Hot Washer...
-
Page 3: Safety Warnings
If the power cable 6. Do not operate the hot washer if is damaged, it must be replaced the cover has been removed. by Clarke International service 7. Do not use the hot washer if a department. power cable or important parts of 15. -
Page 4: Safety Symbol
We recommend Clarke Traffic Film 21. If an extension cable is used, the Remover or Clarke Wash and plug and socket must be of Wax (available from your Clarke watertight construction. -
Page 5: Assembly Instructions
ASSEMBLY INSTRUCTIONS 1. Fit the handle first then the detergent tank, followed by the tool holder and finally the hose hook to the hot washer as shown above using the 4 bolts (for the handle) and screws (for the tool holder, hose hook) supplied. SETUP 1. - Page 6 2. Check that the water filter is fitted into the pump's inlet pipe. 3. Screw the hose connector into place by hand, without the aid of tools until ‘hand tight’. 4. Connect the water supply hose to the snap connection. The hose must have an inside diameter of at least 13 mm (1/2”).
- Page 7 7. Connect the spray lance to the gun assembly and tighten securely by turning the locking ring. 8. Turn the local water tap fully on. • Minimum delivery rate: 15 l/min. • Maximum supply water temperature: 40°C. • Maximum supply water pressure: 1MPa.
-
Page 8: Before Use
CLARKE Traffic Film Remover which is a powerful ‘low foaming’ agent for car cleaning, patio cleaning etc., or CLARKE Wash & Wax, both available from your CLARKE dealer. WARNING: THE USE OF UNSUITABLE CLEANING AGENTS MAY ADVERSELY AFFECT THE SAFETY OF THE HOT WASHER. -
Page 9: Using The Pressure Washer
USING THE PRESSURE WASHER AUTOMATIC STOP SYSTEM The Automatic Stop System stops the hot washer during the bypass phase. Once the hot washer is switched on, the ‘Automatic Stop System’ will start and stop the hot washer automatically whenever the trigger is pulled / released. Sometimes the hot washer may start without pressing the gun trigger, this is normally due to air bubbles in the water or other similar phenomena which do not imply the existence of any defects in the hot washer. -
Page 10: Adjusting The Spray
SWITCHING ON TO WASH WITH COLD WATER 1. To start the pressure washer, squeeze and hold the gun trigger while you press ‘1’ on the master switch. TO WASH WITH HOT WATER: 1. To start the pressure washer, squeeze and hold the gun trigger while you press ‘1’... -
Page 11: Using Detergent
USING DETERGENT 1. Slide the nozzle forward for low pressure operation. 2. Pull the trigger to spray the detergent. • The detergent can ONLY be sprayed when the nozzle is in low pressure mode. CAUTION: IF YOUR EYES COME INTO CONTACT WITH ANY CLEANING FLUIDS, RINSE THEM IMMEDIATELY WITH PLENTY OF CLEAN WATER AND SEEK MEDICAL ADVICE IF REQUIRED. -
Page 12: Care And Maintenance
CARE AND MAINTENANCE WARNING: THE HOT WASHER MUST BE DISCONNECTED FROM ITS POWER SOURCE, BY REMOVING THE PLUG FROM THE SOCKET OUTLET, DURING CLEANING OR MAINTENANCE. WARNING: DO NOT SPRAY THE HOT WASHER WITH WATER OR DETERGENTS/AGGRESSIVE SOLVENTS. THE HOT WASHER COULD BE DAMAGED. -
Page 13: De-Commissioning Product
CONSUMABLES ETC A range of suitable hoses, shampoo and traffic film remover are available from your Clarke dealer. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 14: Troubleshooting
40 degrees. Damaged or warn out Contact Clarke Service nozzle components. Department for replacement Coil is covered in limescale. Contact Clarke Service Department for advice on de- scaling. The burner does Dirty burner nozzle. Contact Clarke Service not turn on. - Page 15 Check air inlet. Contact Clarke noisy. blocked valves. Excess Service Department. water temperature. Reduce water temperature. Oil leaking from Worn out o-rings or gaskets. Contact Clarke Service the pump. Department. Motor suddenly Thermal protection has Switch off the hot washer and stops.
-
Page 16: Product Specifications
PRODUCT SPECIFICATIONS Model Number KING150 Part Number 7320175 Voltage 230 V / 50 Hz / 1 Phase Rated Input Power 2300 W (HOF) Duty Cycle S1 (continuous) Fuel Type Diesel Max Inlet Water Pressure 6 Bar Working Pressure 110 Bar... -
Page 17: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 18 DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 19 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...