Subscribe to Our Youtube Channel
Related Manuals for Clarke KING 300
Summary of Contents for Clarke KING 300
- Page 1 WARNING: Read these instructions before using the machine PROFESSIONAL HIGH PRESSURE HOT WASHER MODEL NO: KING 300 PART NO: 7320182 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC0425...
- Page 2 INTRODUCTION Thank you for purchasing this CLARKE Hot Washer. The machine has been designed to use hot or cold water to clean any surfaces which can stand the force of the high pressure water jet. The machine must only be used for the purpose for which it was designed.
-
Page 3: General Safety Rules
GENERAL SAFETY RULES WARNING: WATER AT HIGH PRESSURE CAN BE DANGEROUS AND CAN CAUSE DAMAGE IF THE OPERATOR IS CARELESS. NEVER ALLOW ANYONE TO OPERATE THIS PRESSURE WASHER UNLESS THEY ARE FAMILIAR WITH THE SAFETY PRECAUTIONS. 1. NEVER direct the spray towards any person or animal. 2. -
Page 4: Safety Devices
SAFETY DEVICES Safety devices serve for the protection of the user and must not be put out of operation or bypassed with respect to their function. OVERFLOW VALVE AND PRESSURE SWITCH While reducing the water supply at the pump head or with the Servopress - regulation the overflow valve opens and part of the water flows back to the pump suction side. -
Page 5: Symbols On The Machine
SYMBOLS ON THE MACHINE The high pressure jet must not be directed at persons, animals, live electrical equipment or at the appliance itself. Read the manual Failing to follow these before use. instructions could result in injury or damage to the machine. -
Page 6: Electrical Connections
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. -
Page 7: Overview Of The Machine
OVERVIEW OF THE MACHINE Cover Water supply connection Spray Lance holder Power supply holder Wheel Pouring vent for filter Water supply connector Handle High pressure connection Control panel High pressure hose Accessory storage compartment Safety latch (hand spray gun) Pump regulator Spray lance Oil drain port High pressure nozzle... -
Page 8: The Control Panel
THE CONTROL PANEL 1. Temperature Controller 2. Power Indicator Lamp 3. Power Switch 4. Ignition Indicator Lamp 5. Boiler Switch (for hot water) 6. Fuel Indicator Lamp 7. Manometer Four different spray nozzles are provided and stored in the control panel. They are to be used for operation at 0, 15, 25 and 40 degrees. - Page 9 Failure to comply with the above conditions causes serious mechanical damage to the pump and the loss of warranty. 1. Connect the supply hose to the water supply. 2. Screw the hose adaptor supplied onto the water inlet to the left of the machine by hand as shown.
- Page 10 ATTACH THE EXTENSION LANCE 1. Connect the extension lance to the gun assembly. FITTING A NOZZLE Fit the appropriate lance nozzle from the selection of four according to the washing temperature to be used. These are stored in clips within the control panel as stated on page 8.
-
Page 11: Turning On The Machine
1. Remove the diesel filler cap and fill the tank with diesel fuel only. • Minimum 4 litres • Maximum 22 litres. 2. Replace the filler cap securely. SETTING THE MACHINE WORKING TURNING ON THE MACHINE 1. Set the switches to desired operating mode. -
Page 12: Operating With Cold Water
SET THE WORKING PRESSURE AND FLOW RATE 1. If the working pressure/water flow rate is unsuitable it can be adjusted using the regulator. 2. Remove the top cover panel to gain access to the regulator by removing the six retaining screws and lifting the panel away. -
Page 13: Operation
OPERATION WARNING: IN CASE OF OPERATION INDOORS, ADEQUATE VENTILATION AND GAS VENTING MUST BE ASSURED. HOLDING THE LANCE 1. Users must hold the gun in the correct position with one hand on the grip and the other on the lance as shown. -
Page 14: Shutting Down The Machine
If you do not intend to used the machine for more than 5 minutes, set the ON/OFF switch to OFF. SHUTTING DOWN THE MACHINE IMPORTANT: After operation with hot water, the machine must be operated with open gun using cold water for two minutes due to the danger of scalding by hot water. -
Page 15: Care And Maintenance
CARE AND MAINTENANCE WARNING: DISCONNECT THE MACHINE FROM THE POWER SUPPLY DURING CLEANING OR MAINTENANCE. WARNING: DO NOT SPRAY THE MACHINE WITH WATER AND DO NOT USE DETERGENTS OR AGGRESSIVE SOLVENTS AS THEY COULD DAMAGE THE MACHINE. 1. Clean the exterior part of the machine with a damp cloth. CLEANING THE WATER INLET FILTER To ensure the pump gives good service it is extremely important to check and clean the water inlet filter frequently. -
Page 16: Troubleshooting
If the problem persists period of running. tripped Contact CLARKE service. When the lance is The nozzle is either Either clean it or replace it. turned on, pressure clogged or deformed. - Page 17 Contact CLARKE service. enough Boiler coil clogged with limescale. For all other problems contact the CLARKE service department. CONSUMABLES A range of suitable hoses, shampoo and traffic film remover, snow-foam and drain cleaner are available from your CLARKE dealer including;...
- Page 18 PUMP COMPONENT PARTS DESCRIPTION DESCRIPTION Pressure gauge Seal Valve cap Seal seating Valve set Seal By-pass set complete Seal seating Total stop set Main oil seal outer Pump flange Main oil seal ring Valve set complete Roller bearing Valve cap Pump main shaft Outlet/non return valve Bearing...
- Page 19 COMPLETE MACHINE PARTS Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 20: Component Parts
COMPONENT PARTS DESCRIPTION DESCRIPTION Cover panel Elbow Cover switch Bridge Control knob Brass union Potentiometer Washer Controls box Electrical connector Printed circuit board Insert LED plate Boiler lid Relay 11kW Chimney cone Thermal protector Piston spring Lower electrical box Boiler closing ring Wheel clip Lid with chimney Wheel... -
Page 21: Product Specifications
Parts set plastic connector Metal lance Quick coupling inlet connector Gun assembly complete Delivery hose PRODUCT SPECIFICATIONS Model Number King 300 Part Number 7320182 Voltage 230 V / 50 Hz / 1 Ph Power cable length 4500mm Ingress Protection Rating... - Page 22 DECLARATION OF CONFORMITY - UKCA Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 23: Declaration Of Conformity (Ce)
DECLARATION OF CONFORMITY - CE Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the KING 300 and is the answer not in the manual?
Questions and answers