Download Table of Contents Print this page

Launch Creader 519 Quick Start Manual

Advertisement

Creader 519
Creader 519 Handset
Diagnostic Cable
LCD Screen
DTC Button*
(To read the diagnostic
trouble codes.)
ESC Button
(To return to the previous screen.)
Erase Button*
(To clear the diagnostic
trouble codes.)
Note:
The buttons marked with * indicate the function hot keys(namely,
F1, F2, F3 and F4) and only apply to Diagnostics.
This Quick Start Guide is subject to change without written notice.
Quick Start Guide
I/M Button*
(Quick access to I/M
readiness function.)
Help Button*
(Provides online tips
for diagnostics.)
DTC
ER
I/M
?
F 1
F 2
F 3
F 4
OK Button
OK
Selection Button
USB Port
(To update your tool via USB cable.)
1. Preparation & Connections
Note: To make sure the tool is running the latest available software,
it is advisable to check for updates on a frequent basis. Refer to
Section 3 "Register & Update" for details.
1. Preparation
Turn the vehicle ignition on.
Vehicle battery voltage range should be 9-14Volts.
Throttle should be in a closed position.
2. Vehicle Connection
1. Locate vehicle's DLC socket: The DLC (Diagnostic Link
Connector) is typically a standard 16-pin connector where
diagnostic code readers interface with a vehicle's on-board
computer. It is usually located 12 inches from the center of
the steering wheel, under or around the driver's side for
most vehicles.
If the DLC cannot be found, refer to the vehicle's service
manual for the location.
DLC Location
2. Connect the diagnostic cable into the vehicle's DLC
socket.
LAUNCH
EN

Advertisement

Table of Contents
loading

Summary of Contents for Launch Creader 519

  • Page 1 Creader 519 Quick Start Guide 1. Preparation & Connections Creader 519 Handset Note: To make sure the tool is running the latest available software, it is advisable to check for updates on a frequent basis. Refer to Section 3 “Register & Update” for details.
  • Page 2: Basic Operations

    Serial Number: The fault code is n ot found in the datab ase If more than one DTC was retrieved, 972890000029  5. Launch the update tool on Register Code: press to view different DTCs. your PC, Fig. B will appear.
  • Page 3: Guía De Inicio Rápido

    L AUNCH Creader 519 Guía de Inicio Rápido Configuración de CReader 519 1. Preparación & Conexiones Nota: Para asegurarse de que se equipo está ejecutando el software disponible más reciente, es recomendable comprobar si hay actualizaciones frecuentemente. Acuda la Sección 3 "Registro y Actualización"...
  • Page 4: Operaciones Básicas

    LAUNCH Creader 519 Guía de Inicio Rápido 3. Registro y Actualización 2. Operaciones Básicas Podrá conectar su equipo para actualizarlo con un cable de USB Mo nito r Statu s Los iconos de la parte inferior de la a un ordenador.
  • Page 5: Guide De Démarrage Rapide

    Creader 519 Guide de démarrage rapide 1. Préparation & Connexions Creader 519 Combiné Remarque: Pour s'assurer que l'outil fait fonctionner les derniers logiciels disponibles, il est conseillé de vérifier les mises à jour fréquemment. Reportez-vous à la section 3 «S'inscrire & Mettre à jour»...
  • Page 6: Opérations De Base

    LAUNCH Creader 519 Guide de démarrage rapide 2. Opérations de base 3. S'inscrire&Mettre à jour Mo nito r Statu s Les icônes en noir au bas de l'écran L'outil peut être mis à jour via un câble USB. MIL Status...
  • Page 7 LAUNCH Creader 519 Schnellstartanleitung 1. Vorbereitung & Anschlüsse Creader 519 Hörer Hinweis: Um sicherzustellen, dass das Werkzeug die aktuellste verfügbare Software ausführt, empfiehlt es sich, regelmäßig nach Updates zu suchen. Für weitere Informationen finden Sie in Abschnitt 3 "Registrieren & Aktualisieren"...
  • Page 8 LAUNCH Creader 519 Schnellstartanleitung 2. Grundfunktionen 3. Registrieren & Aktualisieren Mo nito r Statu s Die schwarzen Symbole am unteren Das Gerät ist über USB-Kabel aktualisierbar. MIL Status Bildschirmende zeigen die Hinweis: Sicherstellen, dass PC ans Internet angeschlossen ist. DT Cs in this E CU verfügbaren Handlungen an, die...
  • Page 9: Краткое Руководство Пользователя

    LAUNCH Creader 519 Краткое руководство пользователя 1. Подготовка и подключение Creader 519 Серия Примечание Убедитесь что у вас установлена последняя версия программного обеспечения Рекомендуем Вам проверить наличие обновлений программного обеспечения Для дополнительной информации обратитесь к разделу 3 'Регистрация и обновление...
  • Page 10: Основные Операции

    LAUNCH Creader 519 Краткое руководство пользователя 2. Основные операции 3. Регистрация и обновление Чёрные значки в нижней части Mo nito r Statu s Вы можете обновить свой прибор с помощью USB-кабеля MIL Status экрана обозначают операции DT Cs in this E CU Примечание...
  • Page 11 LAUNCH Creader 519 取扱説明書 1. 準備 接 続 & 端末 Creader 519 注 意:デ バ イ ス が 最 新 の ソ フ ト ウ ェ ア を 利 用 す る た め 、 頻 繁 に 更 新 を...
  • Page 12 LAUNCH Creader 519 取扱説明書 3.登録&ア ッ プデ ート . 基本操作 Mo nito r Statu s ケ ー ブ ル を 通 じ て デ バ イ ス を ア ッ プ デ ー ト す る こ と は で き ま す 。...
  • Page 13: Guia De Início Rápido

    Creader 519 Guia de Início Rápido 1. Preparação e Conexão Creader 519 Aparelho Nota: Para se certificar de que o software mais recente disponível é utilizado, é recomentado a buscar atualizações com freqüência. Consulte a Seção 3 "Inscrição e Atualização" para obter detalhes.
  • Page 14: Operações Básicas

    LAUNCH Creader 519 Guia de Início Rápido 2. Operações Básicas 3. Inscrição e Actualização Mo nito r Statu s A ferramenta pode ser atualizada via cabo USB. Os ícones em preto na parte inferior MIL Status Nota: Certifique-se de que o PC tem uma ligação à Internet.
  • Page 15 制 作要求 : 装订方式:原始为 210mmx148mm 横向纸张大小, 按 比例输出 ,骑马钉装订 印刷要求:彩色印刷, 书写纸...

Table of Contents