General Safety Information - Barmesa Pumps 2AHS051 Installation, Operation & Maintenance Manual

0.5, 1 & 2 hp @ 3500 rpm submersible dewatering pumps
Table of Contents

Advertisement

Before installation, read the following
instructions
carefully.
follow
instruction
information could cause serious
bodily injury, death and/or property
damage. Each Barmesa product is
carefully inspected to insure proper
performance. Closely following these
instructions will eliminate potential
operating problems, assuring years
of trouble-free service.
DANGER
Indicates an immi-
nently hazardous situation which, if
not avoided, WILL result in death or
serious injury.
WARNING
Indicates an immi-
nenty hazardous situation which, if
not avoided, MAY result in death or
serious injury.
Indicates a potentially
CAUTION
barmesapumps.com
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
IMPORTANT! - Barmesa Pumps is not
responsible for losses, injury or
death resulting from failure to
observe these safety precautions,
misuse, abuse or misapplication of
pumps or equipment.
A L L R E T U R N E D
P R O D U C T S M U S T B E
CLEANED, SANITIZED, OR
D E CO N TA M I N AT E D P R I O R TO
SHIPMENT, TO INSURE EMPLOYEES
WILL NOT BE EXPOSED TO HEALTH
HAZ ARDS IN HANDLING SAID
MATERIAL. ALL APPLICABLE LAWS
AND REGULATIONS SHALL APPLY.
WARNING
Installation, wiring, and
j u n c t i o n c o n n e c t i o n s m u s t b e i n
accordance with the National Electric
Code and all applicable state and local
codes. Requirements may vary depending
on usage and location.
WARNING
Failure
to
servicing is to be conducted by
and
safety
qualified personnel only.
power connected; the rotating cutter
and/or impeller can cause serious
injuty.
may become entangled in moving
parts.
DANGER
before handling or servicing the
p u m p o r a n y a c c e s s o r y i t e m s
associated with or near the pump.
DANGER
human contact with pumped fluid.
DANGER
handling any aspect of the pumping
system. Lock out power & tag.
WARNING
pumps in water over 104 °F. Do not
exceed manufactures recommended
maximum performance, as this could
cause the motor to overheat.
DANGER
shock, burns or death. Never handle
connected power cords with wet
hands. Use appropriate lifting device.
I n s t a l l a t i o n a n d
Keep clear of suction and
discharge openings. Do not
insert fingers in pump with
Always wear eye protection
when working on pumps. Do
not wear loose clothing that
Pumps build up heat
and pressure during
operation. Allow time
f o r p u m p s t o c o o l
T h i s p u m p i s n o t
i n t e n d e d f o r u s e i n
swimming pools or water
installations where there is
Risk of electric shock. To
reduce risk of electric shock,
always disconnect pump
from power source before
D o n o t u s e t h e s e
Do not lift, carry or
hang pump by the electrical
c a b l e s . D a m a g e t o t h e
electrical cables can cause

General Safety Information

WARNING
Ground Fault Circuit
Interrupter (GFCI) to be used with
plug-in type power cord.
DANGER
Failure to permanently
ground the pump, motor and
controls before connecting
to power can cause shock,
burns or death.
DANGER
These pumps are not to
be installed in locations
classified as hazardous in
accordance with the National
Electric Code, ANSI/NFPA 70.
WARNING
The Uniform Plumbing
Code (U P C ) states that sewage
systems shall have an audio and visual
alarm that signals a malfunction of the
systems, that are required to reduce
the potencial for property damage.
IMPORTANT! - Prior to installation,
record Model Number, Serial, Amps,
Voltage, Phase and HP from pump
name plate for the future reference.
Also record the Voltage and Current
Readings at Startup:
Model Number:_____________________
Serial:_____________________________
Amps:___________ Volts:____________
Phase:____________ HP:_____________
01

Advertisement

Table of Contents
loading

This manual is also suitable for:

2ahs101a2ahs051a2ahs1012ahs1032ahs203

Table of Contents