Related Manuals for Barmesa Pumps 2BEH-SS Series
Summary of Contents for Barmesa Pumps 2BEH-SS Series
- Page 1 Installation, Operation & Maintenance Manual Submersible Effluent Pumps 2BEH-SS 0.5 & 1 HP @ 3500 RPM barmesapumps.com IMPORTANT! - Read all instructions in this manual before operating or servicing a pump.
-
Page 2: General Safety Information
IMPORTANT! - Barmesa Pumps is not systems, that are required to reduce installations where there is responsible for losses, injury or the potencial for property damage. -
Page 3: Specifications And Dimensions
Specifications & Dimensions DISCHARGE: 2" NPT, vertical. SPHERICAL SLD HNDLG: 3/4" LIQUID TEMPERATURE: 104° F (40° C) max. VOLUTE: Cast iron ASTM A-48 class 30. MOTOR HOUSING: Cast iron ASTM A-48 class 30. SEAL PLATE: Cast iron ASTM A-48 class 30. IMPELLER: 2 vane, open, with vanes on back side, dynamically balanced ISO G6.3. -
Page 4: Recommendations And Warnings
Recommendations and Warnings Receiving inspection Installation Liquid Level Controls Upon receiving the pump, it should There are two methods of installing The level control(s) should be inspected damage effluent pumps: mounted on the discharge piping, a shortages. If damage has occurred, 1. -
Page 5: Installation & Service
Installation & Service Servicing IMPORTANT! - The overload will then NOTE: Item numbers in ( ) refer to automatically reset and start the Figure 6 and 7. pump up after the motor cools to a safe temperature. In the event of an overload, the source of this condition should be determined and corrected Cooling Oil - Anytime the pump is... - Page 6 Service Pressure Test (If oil has been Pressure builds up extremely To reassemble: drained) - Remove pipe plug (16) fast, increase pressure by 4. Clean the threads with thread "TAPPING" air nozzle. Too locking compound cleaner. Apply from housing (4). Apply pipe sealant much pressure will damage removable Loctite®...
- Page 7 Service 7. Check motor capacitor (29) with an interchange seal 3. Slide retaining ring (5d) and spring Ohm meter by first grounding the components, replace the entire (5c) over shaft and let rest on capacitor by placing a screwdriver bearing. Lightly oil (Do not use shaft seal (6).
- Page 8 Service THREE-PHASE 208/230V AC Cable Assembly: POWER CORD 4x12 14. Check power cord (18) for cracks or damage and replace if required. G L1 Insert one washer (20), grommet (21), washer (20) into motor housing (4). Apply pipe sealant to gland nut (19) and screw into motor housing (4).
- Page 9 Repair Parts Figure 6 barmesapumps.com For Repair Part Please supply: Model Number and Serial as shown on Name Plate, and Part Description and Part Number as shown on Parts List.
- Page 10 Repair Parts Figure 7 barmesapumps.com For Repair Part Please supply: Model Number and Serial as shown on Name Plate, and Part Description and Part Number as shown on Parts List.
- Page 11 Parts List barmesapumps.com For Repair Part Please supply: Model Number and Serial as shown on Name Plate, and Part Description and Part Number as shown on Parts List.
-
Page 12: Troubleshooting Chart
13. Piping attachments to building structure too loose or rigid NOTE: Barmesa Pumps assumes no responsibility for damage or injury due to disassembly in the field. Disassembly of the pumps or supplied accessories other than at Barmesa Pumps or its authorized service centers, automatically voids warranty.
Need help?
Do you have a question about the 2BEH-SS Series and is the answer not in the manual?
Questions and answers