Table of Contents
Related Manuals for Barmesa Pumps 4BSE-DS Series
Summary of Contents for Barmesa Pumps 4BSE-DS Series
- Page 1 Installation, Operation & Maintenance Manual Submersible Solids Handling Pumps 4BSE-DS 4.5, 7.5, 11.3, 15 HP @ 1750 RPM barmesapumps.com IMPORTANT! - Read all instructions in this manual before operating or servicing a pump.
-
Page 2: General Safety Information
IMPORTANT! - Barmesa Pumps is not systems, that are required to reduce installations where there is responsible for losses, injury or the potencial for property damage. -
Page 3: Specifications And Dimensions
Specifications & Dimensions DISCHARGE: 4", 125lb, flange horizontal. SPHERICAL SLD HNDLG: 3" LIQUID TEMPERATURE: 104° F (40° C) max. VOLUTE: Cast iron ASTM A-48 class 30. MOTOR HOUSING: Cast iron ASTM A-48 class 30. SEAL PLATE: Cast iron ASTM A-48 class 30. IMPELLER: 2 vane, open, with vanes on back side. -
Page 4: Recommendations And Warnings
Recommendations and Warnings Receiving inspection Installation Liquid Level Controls Upon receiving the pump, it should These pumps are recommended for The level control(s) should be inspected damage use in a sump, basin or lift station. mounted on the discharge piping, a shortages. -
Page 5: Installation & Service
Installation & Service IMPORTANT! - The overload will then These situations ma y induce a false signal in the moisture etecting automatically reset and start the circuit. If none of the above test pump up after the motor cools to a prove conclusive, the pump(s) should safe temperature. - Page 6 Service a) Inspect motor chamber for oil level If oil is found to be clean and Use soap solution around the sealed Ÿ and contamination. uncontaminated (measuring areas above the oil level and nspect b) Inspect impeller and body for above 15 V breakdown), re ill the joints for "air bubbles".
- Page 7 Service Disassembly Motor and Bearings - Remove Apply adhesive compound to the Impeller and Volute - Disconnect volute, impeller, seal plate and seal as shaft and press bearing (14) onto power. Remove hex nuts (24) and shaft, position squarely onto the previously stated and drain oil from vertically lift motor housing and seal motor housing (3).
- Page 8 Service Motor end Thread cap screws (25) into bearing housing (16) and tighten. Refill Bearing chamber with oil. housing (16) Conduit Box Assembly - Check Moisture Sensor power (34) and control cables (35) for Probe (37) Seal stationary crackes or damage and replace Seal rotating complete conduit box (4) if required.
- Page 9 Service SINGLE-PHASE 230V AC THREE-PHASE 460V AC Impeller and Volute - Install impeller (29) by appling a thin film of oil to L2 L3 G L1 L2 motor shaft and slide impeller straight onto shaft, keeping keyways lined up. Drive key (13) into keyway. Locate washer, apply thread lock primer (such as Loctite®...
- Page 10 Repair Parts Figure 6 barmesapumps.com For Repair Part Please supply: Model Number and Serial as shown on Name Plate, and Part Description and Part Number as shown on Parts List.
- Page 11 Parts List 4.5 H.P., SINGLE PHASE, 230 7.5 H.P., SINGLE PHASE, 230 barmesapumps.com For Repair Part Please supply: Model Number and Serial as shown on Name Plate, and Part Description and Part Number as shown on Parts List.
-
Page 12: Troubleshooting Chart
13. Piping attachments to building structure too loose or rigid NOTE: Barmesa Pumps assumes no responsibility for damage or injury due to disassembly in the field. Disassembly of the pumps or supplied accessories other than at Barmesa Pumps or its authorized service centers, automatically voids warranty.
Need help?
Do you have a question about the 4BSE-DS Series and is the answer not in the manual?
Questions and answers