Table of Contents
Advertisement
Quick Links
2BSE-SS
0.5, 0.75 & 1 HP @ 1750 RPM
barmesapumps.com
2BSE51SS
0.5 HP
2BSE72SS
2BSE73SS
2BSE74SS
0.75 HP
IMPORTANT! - Read all instructions in this manual before operating or servicing
a pump.
Installation, Operation &
Maintenance Manual
Submersible Solids
Handling Pumps
2BSE102SS
2BSE103SS
2BSE104SS
1 HP
Advertisement
Table of Contents
Related Manuals for Barmesa Pumps 2BSE102SS
Summary of Contents for Barmesa Pumps 2BSE102SS
- Page 1 Maintenance Manual Submersible Solids Handling Pumps 2BSE-SS 0.5, 0.75 & 1 HP @ 1750 RPM barmesapumps.com 2BSE51SS 0.5 HP 2BSE102SS 2BSE103SS 2BSE72SS 2BSE104SS 2BSE73SS 1 HP 2BSE74SS 0.75 HP IMPORTANT! - Read all instructions in this manual before operating or servicing...
-
Page 2: General Safety Information
IMPORTANT! - Barmesa Pumps is not systems, that are required to reduce installations where there is responsible for losses, injury or the potencial for property damage. -
Page 3: Specifications
0.75 1750 10.5 17.5 14/3 0.5" 2BSE73SS 62180506 0.75 200/230 1750 12/4 0.625" 2BSE74SS 62180507 0.75 1750 12/4 0.625" 2BSE102SS 62180508 1750 17.5 14/3 0.5" 2BSE103SS 62180509 200/230 1750 14/4 0.625" 2BSE104SS 62180510 1750 14/4 0.625" 12.937" 12.637" 4.875" 6.5"... -
Page 4: Recommendations And Warnings
Recommendations and Warnings Receiving inspection Installation Liquid Level Controls Upon receiving the pump, it should These pumps are recommended for The level control(s) should be inspected damage use in a sump, basin or lift station. mounted on the discharge piping, a shortages. -
Page 5: Installation & Service
Installation & Service IMPORTANT! - The overload will then a) Inspect motor chamber for oil level automatically reset and start the and contamination. b) Inspect impeller and body for pump up after the motor cools to a safe temperature. In the event of an excessive build-up or clogging. - Page 6 Service Pressure Test (If oil has been 5. Remove v-gasket (23) and replace if Pressure builds up extremely drained) - Remove pipe plug (34) damaged. fast, increase pressure by from housing (3). Apply pipe sealant "TAPPING" air nozzle. Too to pressure gauge assembly and much pressure will damage Motor and Capacitor: tighten into hole.
- Page 7 Service Shaft Seal: 4. Place seal’s (24) retaining ring and 9. Place socket head screws (31) 14. Lift motor rotor, shaft, bearing (6), spring onto shaft. Lightly oil (Do not through seal plate into motor housing rotating member of seal, washer (7) and torque to 60 inch pounds.
- Page 8 Service SINGLE-PHASE 115/230V AC THREE-PHASE 208/230V AC THREE-PHASE 460V AC POWER CORD 3x14 POWER CORD 4x12 POWER CORD 4x12 L2 L3 G L1 L2 G L1 CAPACITOR T2 T3 T4 T7 T5 T8 T6 T9 G T1 T2 G T1 T7 T2 T8 T3 T9 T4 T5 T6 MOTOR LEADS MOTOR LEADS MOTOR LEADS...
- Page 9 Repair Parts Figure 5 barmesapumps.com For Repair Part Please supply: Model Number and Serial as shown on Name Plate, and Part Description and Part Number as shown on Parts List.
-
Page 10: Parts List
Parts List ITEM DESCRIPTION QTY. MATERIAL CABLE ASSEMBLY (14AWG-3) O-RING Ø45 x 3.1 NBR 40 PUMP BODY HT200 CAPACITOR 30µ F/300V 90°C ALUMINIUM UPPER BEARING PLATE ZL102 BEARING 6203 WAVE WASHER 65Mn TEMPERATURE PROTECTOR STATOR ROTOR COMPONENT STATOR COMPONENT HEX. HEAD BOLT 5/16"-18UNC x 4" SS 304 SPRING WASHER SS 304... -
Page 11: Troubleshooting Chart
13. Piping attachments to building structure too loose or rigid NOTE: Barmesa Pumps assumes no responsibility for damage or injury due to disassembly in the field. Disassembly of the pumps or supplied accessories other than at Barmesa Pumps or its authorized service centers, automatically voids warranty.
Need help?
Do you have a question about the 2BSE102SS and is the answer not in the manual?
Questions and answers