Trouble Shooting Table; Possibilities To Extend The System; Extension Of The System With A Subsystem; Extension Of The System With A Communicator - jablotron JA-65 MAESTRO Installation Manual

Problem
alarm after first powering
connected JA-60E keypad has no
function
impossible to enroll a wireless item location of the item is not suitable and the radio signal level is too low
a fault is indicated on the keypad
and it is beeping
If JA-65X is used, telephone line
failure is indicated and the phone
works as normal
PIR movement detector repeatedly
triggers alarms with no visible
reason
fault or alarm C is indicated
system does not communicate
with connected PC
problem is not in this list

17. Possibilities to extend the system

The JA-65 alarm system is a kit which can be tailor
configured according to the size of the house or the needs of
the user. It can combine wireless and wire operated
components.

17.1 Extension of the system with a subsystem

An additional JA-65 or JA-60 control panel can be enrolled as
a subsystem to the control panel (see 11.12.). Each system
then works as an independent system. However, any event in
the subsystem (alarm, tampering, failure or low battery) will
trigger the same kind of event on the main control panel (the
main control panel will display "J" as the event source). The
main control panel will not indicate the number of the item
which triggered the event, but this information is available on
the subsystem's control panel.
Using this method, multiple level subsystems can be chained.
Warning: never enroll the top level control panel as a
subsystem of the lower level control panel. This would create
endless circle for the data and such an alarm system chain
would not work properly.
Alarm system JA-65 MAESTRO

16. Trouble shooting table

possible cause
the control panel is not in factory default setting
connecting cable does not connect the corresponding positions in the
keypad and in the control panel (1-1, 2-2, 3-3, 4-4)
(too far away or an obstacle is in the way of communication)
check display for the reason of the trouble. Press key N to disable
beeping. The trouble information is stored in the event memory and it
can be reviewed entering F4 anytime in the future
when you make a phone call longer than 15 minutes, it is interpreted
by the system that the tel. line is not ready.
check if there are: animals in the protected area (mice...), sudden
changes of temperature or intense air circulation, movement of
objects with temperature of about 37°C etc.
blown fuse in the control panel or radio communication jamming
the PC-60A cable is not connected to the correct COM connector on
the PC
call installer or the distributor for advice

17.2 Extension of the system with a communicator

GSM communicator JA-60GSM
By using GSM communicator JA-60GSM you will get supervision
over the system wherever you are. Communicator sends SMS
messages, calls to predefined telephone numbers and plays
audible warning, communicates with 2 CMS, allows remote
access from a phone's keypad and can be set and operate via
web page www.GSMlink.cz.
Digital communicator JA-65X
Communicator JA-65X can communicate with a Monitoring
Station, send two voice messages, send five SMS messages
via SMS server (if it is supported in your country or dial a
numeric Pager). It can also communicate with a remote PC
(using ComLink SW and a JA-60U modem). By remotely
connected PC it is possible to set and/or operate the control
panel.
17.3 Brief overview of parts suitable for the JA-63
system
The brief overview you got along with this manual includes the
basic assortment of accessories. Jablotron is systematically
introducing new and improved items to the market. You can get
the most current information from your distributor or you can visit
Jablotron's Internet home page at: www.jablotron.com
- 16 -
solution
perform a factory default reset
Check the colors of the cores in the cable
and positions on each side
change location of the item, (fix it in the
new place temporary at first and then try it)
check the reason of the trouble in user
manual and fix it, or call the installer
if this problem repeats, disable tel. line
checking in programming mode
increase detector's immunity (internal
setting), change location of the detector or
use an optional sensor's lens
PC with Comlink SW gives details
check the connection or select the port
number in SW manually
local hot line number:
MFM53003