DFI PL610-C622 User Manual page 37

BMC Configuration
This section configures the BMC related settings.
InsydeH2O Setup Utility
Advanced
BMC Confi guration
Watchdog Timer Support <Disabled>
Not disable in OS <Disabled>
Watchdog Timer Timeout [5]
Watchdog Timer Action <Hard Reset>
Power Button <Enabled>
Reset Button <Enabled>
 User Confi guration
Lan Port Confi guration <Dedicated>
LAN Channel Number [3]
IPv4 Source <DHCP>
IPv4 IP Address 0.0.0.0
IPv4 Subnet Mask 0.0.0.0
IPv4 Gateway Address 0.0.0.0
IPv6 Mode <Disabled>
IPv4 IP Address [64]
IPv4 Subnet Mask 0:0:0:0:0:0:0:0
IPv4 Gateway Address 0:0:0:0:0:0:0:0
F1 Help ↑/↓ Select Item F5/F6
Esc Exit ←/→ Select Item Enter

Watchdog Timer Support
Enable or disable BMC watchdog timer at start of POST.
Not disable in OS
Enable or disable BMC watchdog when boot to OS.
Watchdog Timer Timeout
Enter the number of minutes the system firmware has to boot the OS before it takes
the timeout action. Valid values are from 2 to 8 minutes.
Watchdog Timer Action
Select timeout action: No Action, Hard Reset, Power Down, or Power Cycle.
Power Button
Enable or disable power button function.
Reset Button
Enable or disable reset button function.
Chapter 3 BIOS Setup
Chapter 3
Rev. 5.0
Enable/Disable IPMI Sup-
port. Note: If changing to
enable, BMC detailed in-
formation only valid after
rebooting.
Change Values F9 Setup Defaults
Select SubMenu F10 Save and Exit

User Configuration
Advanced
User Confi guration
User ID
User Status
User Password
Channel
Privilege
Add current setting to list
--------------------
User Id UserName UserStatus Channel Privilege
1 dfi Enabled
2 root Enabled
3 test1
Enabled
4 Disabled
5 Disabled
6 Disabled
7
Disabled
8 Disabled
9 Disabled
10 Disabled
11
Disabled
12
Disabled
13 Disabled
14 Disabled
15 Disabled
F1 Help ↑/↓ Select Item
Esc Exit ←/→  Select Item
User ID
Enter the user ID number for BMC. The max. number is 15.
User Status
Enable or disable the user status.
User Password
Enter the user password.
Channel
Enter the LAN channel number for BMC. The valid LAN channel number is 1, 2, or 3.
Privilege
Select the privilege: Reserved, Callback, User, Operator, Administrator, or No Access.
Add current setting to list
Select this field and press Enter to add current setting to list.
37
InsydeH2O Setup Utility Rev. 5.0
This is User ID for BMC,
Set/Get User information
[1]
according to it. The MAX
<Enabled>
User ID number : 15
[3]
<Administrator>
1/2/3 Admin/Admin/Admin
1/2/3 Admin/Admin/Admin
1/2/3 Admin/Admin/Admin
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
1/2/3 N/A/N/A/N/A
F5/F6 Change Values F9 Setup Defaults
Enter Select SubMenu F10 Save and Exit

www.dfi .com