Sharp MD-X60H Operation Manual page 54

YO <P=001>
(Continued)
When an error message is displayed, proceed as follows:
Error messages
Nothing is recorded.
BLANK MD
Can't COPY You tried to record from a copy-protected disc.
A track cannot be edited.
Can't EDIT
Can't REC Recording cannot be performed correctly due to vibra-
tion or shock in the unit.
Timer recording is impossible or there is no available
Can't T REC
space on the MD.
There is something wrong with the CD changer.
CH ERROR
CONNECT ERR Whilst an MD player is being edited on this unit, incorrect
digital signals are input from the portable MD player.
Since this disc has scratches on it, the recording oper-
DEFECT
ation was skipped.
Incorrect digital signals are input.
Din UNLOCK
The disc is damaged.
DISC ERR
A TOC is not written on the MD or there is something
wrong with data.
DISC FULL The disc is out of recording space.
EDIT OVER There is no space to make CD editing on the disc.
A disc has not been loaded.
FOCUS ERROR
The disc data cannot be read.
MD ERROR No operation.
MECHA ERR There is a mechanical problem and the disc is not work-
ing properly.
( :N umber or
symbol)
The number of characters for the disc name or track
NAME FULL
name exceeds 100.
NO DISC A disc has not been loaded.
The disc data cannot be read.
NOT AUDIO The data recorded on this disc is not audio data.
PLAYBACK MD You tried to record on a playback-only disc.
PROTECT Trouble is found.
The disc is write protected.
PROTECTED
The tape is protected against accidental erasure.
The tape mechanism is defective.
TAPE ERROR
TEMP OVER The temperature is too high.
TOC ERR The disc is damaged.
( :Number or
TOC information cannot be read.
symbol)
MD not specified.
TOC FULL There is no space left for recording character information
(track names, disc names, etc.).
( :Number or
symbol)
Recording is impossible.
TOC W ERROR
TRAY ERROR The CD tray operates incorrectly.
U TOC ERR TOC information recorded on the MD does not match
the MD specifications or it cannot be read.
( :Symbol)
U TOC W ERR The TOC information could not be created properly due
to a mechanical shock or to scratches on the disc.
? DISC The data contains an error.
00:00 Music is not being recorded.
Meaning
53
MD-X60H(SUK) TINSE0227AWZZ
Remedy
Replace it with another disc.
Replace it with a regular disc that can be copied.
Change the stop position of the track and then try editing
it.
Re-record.
Replace it with another disc.
Set this unit to the stand-by mode and then back to on, 0 6
and press the button.
Make sure the cable is connected correctly and that
power is being supplied to the portable MD player.
Replace it with another disc.
Connect correct digital signals.
Use the analogue input sockets.
Reload the disc or replace it.
Replace the disc with another recordable disc.
Replace it with a disc that has enough time to record.
Reload the MiniDisc.
Contact the shop where you purchased the unit.
Set this unit to the stand-by mode and press the
ton.
Shorten the disc or track name.
Load a disc.
Reload the disc.
Select another track.
Replace the disc.
Replace it with another recordable disc.
Restart the unit. If the unit doesn't work, contact a
SHARP Authorised Servicing Dealer or SHARP Auth-
orised Service station.
Move the write protection tab back to its original position.
Cover the accidental erase prevention hole.
Try pressing the RESET button.
Set this unit to the stand-by mode and wait for a while.
Replace it with another disc.
Replace it with another recordable disc.
Contact the shop where you purchased the unit.
Unplug the AC power lead, plug it back, and then turn
the power on.
Replace it with another disc.
Erase all of the track, and try recording.
Set this unit to the stand-by mode and try to write the
TOC again.
(Remove any source of shock or vibration whilst writing.)
Replace it with another disc.
Replace the disc with another recordable disc.
7
but-