Bezzera B2013 Instruction Manual page 34

BEZZERA B2013-C2013 Compact
MOD.
of the tap, the greater the quantity of steam sup-
plied will be.
4) Once the output of steam is concluded, remove
the fluid container and clean immediately the
steam nozzle with a wet cloth from the residues
of the heated fluid.
Warning: Do not touch the steam nozzle
directly because it is hot.
DE Model whit automatic steam nozzle
The machine is also equipped with automatic steam
nozzle with temperature sensor (Fig. 01-01A; pos.
4a); to operate this nozzle press the button (Fig.
06; pos. g). The steam flow can be stopped before
reaching the set temperature by pressing again the
same button. By holding down the button (Fig. 06;
pos. g) steam is continuously supplied until the but-
ton is released. To avoid suction of fluid into the
boiler, discharge the steam by pressing the button
(Fig. 06; pos. g).
To change the "texture" of air bubbles present in
the fluid to be heated, operate on the adjusting
screw (closed small bubbles – open big bubbles
(Fig. 12) starting from the open condition (large
bubbles) and reducing gradually the air flow until
reaching the "texture" desired..
To change temperature setting, follow the instruc-
tions in paragraph 5.7 of this handbook.
Warning: To make a cappuccino, we recommend
the use of milk at a temperature of 5 ° C.
5.5 Picking up of hot water
1) Position the water container under the nozzle
(Fig. 01-01A; pos 5).
PM Model
2) Press key (Fig. 01-01A; pos. 2) to pick up the
quantity of water needed.
DE Model
2) Press key (Fig. 06; pos. e) to pick up the quantity
of water needed.
Warning: Do not touch the nozzle di-
rectly because it is hot.
5.6 Turning off the machine
1) Close the water shut-off valve
2) Bring the switch (Fig. 01-01A; pos 10) in pos
"OFF" (Red light (Fig. 01-01A; pos. 15) turn
OFF).
3) Bring the omnipolar switch of the electric net-
work in idle position "0".
4) Exhaust the pressure of the steam tap.
5.7 Programming of doses
To adjust doses in DE machines, proceed as fol-
lows:
press the continuous output /programming/stop
key (Fig. 06; post f), keep it pressed until the relative
light starts flashing, notifying (the machine must not
supply water) the beginning of the programming
function which lasts 4 seconds (DE Model), 30 sec-
onds (DE Model whit automatic steam nozzle) if a
key to program is not pressed.
Activate the output of any key of the keyboard (Fig
06; pos a - d, g) to start programming which will
be memorized when the key will be pressed again
to stop output.
Repeat this operation for all keys in order to pro-
gram the wanted doses.
By programming the first group on the left, the set-
tings will be automatically transmitted to the other
groups. To set different programming between one
group and the other, set them individually.
For setting the automatic steam nozzle (Fig. 01-
01A; pos. 4a), insert this last into the fluid to be
heated, press the button (Fig. 06; pos. g) and wait
until temperature reaches the desired value; press
again the button (Fig. 06; pos. g) to confirm set-
ting.
Warning: Models DE ensure the setting
of the coffee volume by dose. The auto-
matic steam nozzle ensures to reach the
desired temperature.
5.7.1 "PRE-BREWING" programming
The possibility to select the "PRE-BREWING" func-
tion has been foreseen.
Machine off. Turn on the machine by pressing:
- key "a" (Fig. 06) of the first group to ENABLE
PRE-BREWING.
The system confirms the operation, keeping light
34
(DE Model)