Table of Contents
Advertisement
Advertisement
Chapters
Table of Contents
Related Manuals for Sena LinkIn Ride Pal III
Summary of Contents for Sena LinkIn Ride Pal III
- Page 1 User’s Guide...
-
Page 2: Table Of Contents
8.5 Assigning Speed Dial ..........25 3.2 Speed Dialing ............14 8.6 Enabling/Disabling Voice Prompts ......26 3.3 GPS Navigation ............. 15 8.7 Enabling/Disabling Sidetone ........26 3.4 Sena SR10, Two-Way Radio Adapter ..... 15 8.8 Enabling/Disabling Advanced Noise Control™ ..27... - Page 3 8.9 Delete All Bluetooth Pairing Information ....27 SAFETY INFORMATION ........37 8.10 Factory Reset ............28 • Product Storage and Management ......37 8.11 Exit Voice Configuration Menu......... 28 • Product Use ..............37 • Battery ............... 39 FIRMWARE UPGRADE ........29 PRODUCT WARRANTY AND DISCLAIMER ..
-
Page 4: Getting Started
1.2 Powering On and Off 1 GETTING STARTED To power on the headset, press the Center Button and the (+) Button at the same time while hearing ascending beeps and a voice 1.1 Button Operation prompt, “Hello”. To power off the headset, Center Button press the Center Button and the (+) Button at the same time while hearing descending beeps... -
Page 5: Charging
1.3 Charging Note: You can charge the headset by connecting the The battery normally lasts 7 hours of usage supplied USB power & data cable into a time. computer’s USB port or USB wall charger. You can use any standard micro USB cable to 1.4 Checking the Battery Level charge the unit. -
Page 6: Volume Adjustment
1.4.2 Voice Prompt Indicator MP3 music. However, if you adjust the volume during stand-by mode, it will affect volume When you power on the headset, keep levels of every audio source. pressing the Center Button and the (+) Button simultaneously for about 5 seconds until you 1.6 LS2 Bluetooth Device hear three, high toned beeps. -
Page 7: Pairing The Headset With Bluetooth Devices
2. Tap the (+) Button until you hear a voice the first time, you will need to pair them prompt, “Phone pairing”. together. You can pair the LINKIN Ride Pal III 3. Search for Bluetooth devices on your with Bluetooth mobile phones, Bluetooth stereo mobile phone. -
Page 8: Multipoint Pairing - Second Mobile Phone, Gps, And Sr10
Bluetooth connection 3. Search for Bluetooth devices on the HFP immediately. device. Select the LINKIN Ride Pal III in 2. If the Bluetooth connection between the the list of the devices detected on the HFP headset and a media player is disconnected, device. -
Page 9: Advanced Selective Pairing: A2Dp Stereo Or Handsfree
2.3 Advanced Selective Pairing: Note: A2DP Stereo or Handsfree 1. The Sena SR10 is a Bluetooth two-way radio When you are using a smartphone, sometimes adapter for group communication, and uses you may need to selectively use the headset Hands-Free Profile. The incoming audio from... -
Page 10: Seconds Until You Hear A Voice Prompt, "Configuration Menu
2.3.1 A2DP Stereo Music Only 2.3.2 HFP for Phone Call Only 1. Press and hold the Center Button for 12 1. Press and hold the Center Button for 12 seconds until you hear a voice prompt, seconds until you hear a voice prompt, “Configuration menu”. -
Page 11: Intercom Pairing
2.4 Intercom Pairing 3. Tap the Center Button on any one of the two headsets A and B, and wait unit the LEDs 2.4.1 Pairing with Other LINKIN Ride of both headsets turn to blue and intercom Pal III Headsets for Intercom connection is automatically established. -
Page 12: Mobile Phone, Gps, Sr10
Models for Intercom Conversation tap the Center Button to answer the call. The LINKIN Ride Pal III can be paired with all 2. To end a call, press the Center Button for other Sena headset models such as the 20S, 2 seconds until you hear a mid-tone single 10C and the 10S for intercom conversation. - Page 13 4. There are several ways to make a phone Note: call: 1. If you have two phones connected to your • Enter numbers on your mobile phone’s headset and you have an incoming call from keypad and make a call. Then the call is the second phone during the call of the first automatically transferred to the headset.
-
Page 14: Speed Dialing
3.2 Speed Dialing 4. After selecting the last number redial menu, you will hear a voice prompt, “Last number You can quickly make a phone call by using redial”. Then, to redial the last phone call the voice speed dial menu. number, tap the Center Button. -
Page 15: Gps Navigation
Bluetooth intercom simultaneously by using the function. Sena SR10, a Bluetooth Two-way Radio 2. You need to assign speed dial numbers Adapter (please refer to section 2.2, “Multipoint before using the speed dial (please refer to Pairing - Second Mobile Phone, GPS, and section 8.5, “Assigning Speed Dial”). -
Page 16: Stereo Music
1. To play or pause music, press the Center 4 STEREO MUSIC Button for 1 second until you hear a double beep. 2. To adjust the volume, tap the (+) Button or Bluetooth Stereo Music the (-) Button. The Bluetooth audio device must be paired 3. -
Page 17: Music Sharing
5.1, “Starting Two-way Intercom”). Pairing”. When you terminate music sharing, you can go The LINKIN Ride Pal III can connect with all back to the intercom conversation. To start or versions of the LINKIN Ride Pal III Bluetooth terminate sharing music, press the Center headsets and Sena Bluetooth headsets. -
Page 18: Ending Two-Way Intercom
5.2 Ending Two-way Intercom To terminate an intercom conversation, single tap the Center Button. Any intercom connection with any intercom friend will be terminated by a intercom friend single tapping. A double or triple tapping will do nothing in this case. intercom friend End Two-way Intercom Conversation intercom friend... -
Page 19: Intercom And Mobile Phone Call
5.3 Intercom and Mobile Phone Unlike other motorcycle Bluetooth Call headsets, this prevents a user from being dropped out of an intercom conversation 1. When you have an incoming mobile phone by an incoming mobile call. call during an intercom conversation, 2. -
Page 20: Universal Intercom
You can have an intercom conversation with conversation. You can pair the headset with non-Sena Bluetooth headsets using the only one non-Sena Bluetooth headset so if you Universal Intercom function. Non-Sena pair with a different non-Sena Bluetooth Bluetooth headsets can be connected to the headset, the previous pairing will be removed. -
Page 21: Two-Way Universal Intercom
7 FUNCTION PRIORITY You can initiate the Universal Intercom connection with non-Sena Bluetooth headsets The LINKIN Ride Pal III operates in the using the same intercom connection method as following order of priority: you would between other LRP headsets. You... -
Page 22: Configuration Setting
4. If no button is pressed within 10 seconds, 8 CONFIGURATION the headset will exit the configuration and go back to stand-by mode. SETTING 5. If you want to exit the configuration You can set the configuration of the LINKIN immediately, Tap the (+) Button or the (-) Button until you hear a voice prompt, “Exit Ride Pal III by the voice menu instruction... -
Page 23: Mobile Phone Pairing
8.1 Mobile Phone Pairing Phone pairing “Phone pairing” Voice Prompt Multipoint Pairing Factory Default Phone selective pairing Media selective pairing To go into mobile phone pairing mode, tap the (+) Button or the (-) Button until you hear the Speed dial voice prompt, “Phone pairing”. -
Page 24: Phone Selective Pairing
8.4 Media Selective Pairing To go into multipoint pairing mode, tap the (+) Button or the (-) Button until you hear the voice "Media selective prompt, “Multipoint pairing”. Please refer to Voice Prompt pairing" section 2.2 for details on second mobile phone pairing. -
Page 25: Assigning Speed Dial
8.5 Assigning Speed Dial 4. Call a phone number you want to assign and you will hear a voice prompt, “Save Voice Prompt "Speed dial" speed dial (#)”. The phone number is Factory Default automatically assigned to the selected speed dial number. Then the phone call will Execute Tap the Center Button hang up before being connected. -
Page 26: Enabling/Disabling Voice Prompts
8.6 Enabling/Disabling Voice 8.7 Enabling/Disabling Sidetone Prompts “Sidetone” Voice Prompt “Voice prompt” Voice Prompt Factory Default Disable Factory Default Enable Enable/Disable Tap the Center Button Enable/Disable Tap the Center Button Sidetone is audible feedback of your own voice. It helps you to naturally speak at the You can disable voice prompts by configuration setting, but the following voice correct level according to varying helmet noise... -
Page 27: Enabling/Disabling Advanced Noise Control
8.8 Enabling/Disabling Advanced 8.9 Delete All Bluetooth Pairing Noise Control™ Information “Noise control” “Delete all pairings” Voice Prompt Voice Prompt Factory Default Enable Factory Default Enable/Disable Tap the Center Button Execute Tap the Center Button When Advanced Noise Control is enabled, the To delete all Bluetooth pairing information of background noise is reduced during an the headset, tap the (+) Button or the (-) Button... -
Page 28: Factory Reset
To restore factory default settings on the To exit voice configuration menu and get back LINKIN Ride Pal III, tap the (+) Button or the (-) Button until you hear a voice prompt, “Factory to stand-by mode, tap the (+) Button or the (-) reset”, and tap the Center Button to confirm. -
Page 29: Firmware Upgrade
Tap (+) Button or (-) Tap Center 9 FIRMWARE UPGRADE Button Button Phone Pairing None The LINKIN Ride Pal III supports firmware upgrades. You can update the firmware using Multipoint Pairing None the LS2 Bluetooth Device Manager (please Phone Selective Pairing None refer to section 1.6, “LS2 Bluetooth Device... -
Page 30: Troubleshooting
10.2 Intercom Reconnection 10 TROUBLESHOOTING If your intercom friend goes out of range while having an intercom conversation, you may hear static noise and eventually the intercom will be 10.1 Intercom Failure disconnected. In this case, the LINKIN Ride When you try to start an intercom conversation Pal III automatically tries to reconnect the with an intercom friend who is unavailable intercom every 8 seconds and you will hear... -
Page 31: Fault Reset
10.3 Fault Reset 10.4 Factory Reset When the headset is not working properly or is If you want to restore the headset to factory in faulty status for any reason, you may reset default settings, use the Factory Reset in the configuration menu. -
Page 32: Operation Quick Reference
11 OPERATION QUICK REFERENCE Type Function Button Command Beep Basic Function Power on Press the Center Solid blue Ascending beeps Button and the (+) Button for 1 second Power off Tap the Center Button Solid red Descending beeps and the (+) Button Volume adjustment Tap the (+) Button or the (-) Button... - Page 33 Type Function Button Command Beep Red flashing Press the Center Intercom Intercom pairing Mid-tone single beep Button for 5 seconds Tap the Center Button of any one of the two headsets Start/End each Tap the Center Button intercom Music Play/Pause Bluetooth Press the Center Mid-tone double beep music...
-
Page 34: Certification And Safety Approvals
CERTIFICATION AND SAFETY This equipment has been tested and found to comply with the limits for a digital device APPROVALS pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable FCC Compliance Statement protection against harmful interference in a This device complies with part 15 of the FCC residential installation. -
Page 35: Fcc Rf Exposure Statement
CE Declaration of Conformity • Connect the equipment into an outlet on a circuit different from that to which the This product is CE marked according to the receiver is connected. provisions of the R&TTE Directive (1999/5/EC). • Consult the dealer or an experienced radio/ Hereby, LRP declares that this product is in TV technician for help. -
Page 36: Bluetooth License
WEEE (Waste Electrical and (2) This device must accept any interference, Electronic Equipment) including interference that may cause undesired operation of the device. The crossed-out wheel bin symbol on the product, literature, Bluetooth License or packaging reminds you that all ®... -
Page 37: Safety Information
• Do not paint the product. Paint may obstruct SAFETY INFORMATION moving parts or interfere with the normal Please ensure that the product is properly used operation of the product. by observing the warnings and cautions below • Do not drop or otherwise shock the product. to prevent any risk and/or damage to property. - Page 38 • Use of the product at a high volume for a • In any place where wireless communication is long period of time may damage your prohibited, such as hospitals or airplanes, eardrums or hearing ability. Keep the volume turn off the power and refrain from using the at a modest level.
-
Page 39: Battery
• If the product is damaged, stop using it • Store the battery at temperatures of 15 °C ~ 25 °C (59 °F ~ 77 °F). Higher or immediately. It may cause damage, explosion, or fire. lower temperatures may reduce the capacity and life of the battery, or may cause Battery temporary non-operation. -
Page 40: Product Warranty And Disclaimer
PRODUCT WARRANTY AND Warranty Period LRP guarantees free-of-charge replacements DISCLAIMER of defective parts of the product or flaws that may have occurred due to problems in Limited Warranty manufacture for a period of 2 years from the Limited Warranty date of initial purchase. LRP guarantees the product quality based on Termination the technical specification stated in the... - Page 41 LRP and Sena Technologies, Inc. ("Sena") with 5. You must read and understand the regard to any occasion such as difficulty, following warnings and alerts:...
- Page 42 • LRP and Sena together with employees, • Risk factors, which may occur when you managers, partners, subsidiaries, use the product, may be due to errors of representatives, agents, supporting firms the manufacturer, its agents, or third parties which are involved in the and suppliers, sole sellers of LRP and manufacturing.
-
Page 43: Warranty Exclusions
Warranty Exclusions Limitation of Liability TO THE FULL EXTENT ALLOWED BY LAW, Reasons for Limited Liabilities LRP EXCLUDES FOR ITSELF AND ITS If you do not return the product after SUPPLIERS ANY LIABILITY, WHETHER BASED purchasing it, you relinquish all rights to IN CONTRACT OR TORT (INCLUDING liabilities, loss, claims, and claims for NEGLIGENCE), FOR INCIDENTAL,... - Page 44 • In the event the product is damaged REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. IN ANY CASE, THE because the user has used any parts or TOTAL COMPENSATION LIABILITIES OF LRP software which are not provided by the OR ITS SALES AGENTS SHALL NOT EXCEED manufacturer.
-
Page 45: Warranty Service
Warranty Service To obtain product warranty service, send the defective product, at your expense, to the manufacturer or the seller along with proof of purchase (a receipt that shows the purchase date, a product registration certificate of the Website, and other relevant information). Take necessary measures to protect the product.