OutBack Power RADIAN Series Quick Start Manual

Setup and Programming
CAUTION: Equipment Damage
!
These procedures should be done by a qualified installer who is trained on programming inverter power systems.
Failure to set accurate parameters for the system could potentially cause equipment damage. Damage caused by
inaccurate programming is not covered by the limited warranty for the system.
IMPORTANT
Check the firmware revision of all OutBack devices before use. The Radian inverter and MATE3 system display may not
communicate or operate correctly unless their firmware is above a specified revision number.
For models GS8048A and GS4048A, the firmware must be revision 001.005.xxx or higher.
The MATE3 must be revision 002.017.xxx or higher.
Configuration Wizard
The MATE3 Configuration
Settings
Wizard allows quick setup of
Configuration Wizard Configuration Wizard
Device Data Logs
parameters that apply to all
Event Logs
Firmware Update
systems. The Configuration
Wizard is reached from the
MATE3 Main Menu as shown
New Configuration
New Configuration
to the right.
Existing Configuration
Restore Configuration
New Configuration Initialized
The firmware revision of all
devices can be confirmed by
Back Continue
navigating from the MATE3
Main Menu as shown below.
Upgrades to the firmware
Off Grid
revision can be downloaded
from the OutBack website
System Type Off Grid
www.outbackpower.com.
System Voltage 48 VDC
Array Wattage 1000
Battery Type FLA Capacity
Firmware Revision
Back
Absorb Voltage 57.6 VDC
Settings >>
Float Voltage 54.4 VDC
Configuration Wizard Settings >>
Equalize Voltage 60.0 VDC
Device Data Logs >>
Re-Float Voltage 44.0 VDC
Event Logs >>
Firmware Update >>
Back
AC Output Voltage 240 VAC
System System >>
AC Phase Single
Inverter >>
AC Input Breaker Size 50 A
Charge Controller >>
Maximum Output Load 33 A
Battery Monitor >>
MATE3 >> Back
Generator Installed Y
System Information >>
Generator Type AC
Save / Store Information >>
Generator Start Manual
Firmware Version >>
AUX Output Device Port 1
Date and Time >>
LCD Display >>
Back
Note: See the MATE3
manual for details on
MATE3 002.017.018
generator control.
1: GS8048A 001.005.002
2: GS8048A 001.005.002
If FN-DC is installed...
Shunt A
Connection Inverter
S
This advances the display to the
Setup Complete screen. Back
C This advances the display to the
Setup Complete screen if the
Shunt B
Connection Charge Controller
FLEXnet DC is not installed. If the
FLEXnet DC is installed, the display Back
advances to the Shunt screens.
Shunt C
Connection Charge Controller
Back
900-0162-01-00 Rev A.vsd\Page-1\2014-01-24
©2014 OutBack Power Technologies. All Rights Reserved.
>>
>>
Grid Tied Backup
>>
>>
>>
System Type Grid Tied System Type
System Voltage 48 VDC System Voltage
Array Wattage 1000 Array Wattage
Battery Type FLA Capacity 500 Ah
Battery Type
>>
Back Continue Back
>>
>>
Absorb Voltage 57.6 VDC Time 1.0
Absorb Voltage
Float Voltage 54.4 VDC Time 1.0
Float Voltage
Equalize Voltage 60.0 VDC Time 3.0
Equalize Voltage
Re-Float Voltage 44.0 VDC
Re-Float Voltage
Back Continue Back
AC Output Voltage 240 VAC
AC Output Voltage 240 VAC
AC Phase Single
AC Phase
AC Input Breaker Size 50 A
AC Input Breaker Size 50 A
Maximum Output Load 33 A Maximum Output Load
Back Continue Back
Generator Installed N
Generator Installed
Generator Type AC Size 5.0 kW
Generator Type
Generator Start Manual
Generator Start
AUX Output Device Port 1
AUX Output Device Port 1
Back Continue Back
500 Ah
Continue
Period 1 Enable N
Weekday Use 0:00 Drop 0:00
Weekend Use 0:00 Drop 0:00
Time 1.0
Time 1.0 Back Continue Back
Time 3.0
Continue
Period 2 Enable N
Weekday Use 0:00 Drop 0:00
Back Continue Back
Continue
Period 3 Enable N
Weekday Use 0:00 Drop 0:00
Size 5.0 kW Back
Back Continue
Continue
C
Mode Disabled Mode Disabled
Grid Connect 48.0 VDC Delay 60 Min Grid Connect
Grid Disconnect 52.0 VDC Delay 60 Min Grid Disconnect
Grid Connect SOC 60% Disconnect SOC 95% Grid Connect SOC 60%
Back Continue Back
C
If FN-DC is installed... If FN-DC is installed...
Shunt A
Connection Inverter
Back Continue Back
Continue
Shunt B
Connection Charge Controller
Continue Back Continue Back
Shunt C
Connection Charge Controller
Back Continue Back
Continue
S S
Quick Start Guide
WARNING: Fire/Explosion Hazard
Do not place combustible or flammable materials within 12 feet (3.7 m) of
the equipment. This unit employs mechanical relays and is not ignition-
protected. Fumes or spills from flammable materials could be ignited by sparks.
WARNING: Personal Injury
Use safe lifting techniques and standard safety equipment when working with
this equipment.
IMPORTANT:
Clearance and access requirements may vary by location. Maintaining a 36"
(91.4 cm) clear space in front of the system for access is recommended.
Consult local electric code to confirm clearance and access requirements
for the specific location.
Backup
48 VDC
1000
FLA Capacity 500 Ah
Continue
57.6 VDC Time 1.0
54.4 VDC Time 1.0
60.0 VDC Time 3.0
44.0 VDC
MATE3
Continue
System
Display and
Controller
Single
33 A
Continue
N
AC Size 5.0 kW
Manual
Continue
Period 1 Enable N
Weekday Use 0:00 Drop 0:00
Weekend Use 0:00 Drop 0:00
Continue
Period 2 Enable N
Weekday Use 0:00 Drop 0:00
Continue
Period 3 Enable N
Weekday Use 0:00 Drop 0:00
Continue
HUB 10.3
48.0 VDC Delay 60 Min
52.0 VDC Delay 60 Min
Communications
Disconnect SOC 95%
Continue Manager
C
Shunt A
Connection Inverter
Continue
GS Load Center
(GSLC)
Shunt B
Connection Charge Controller
Continue
Contact Technical Support:
Shunt C
Telephone: +1.360.618.4363
Connection Charge Controller
Email: Support@outbackpower.com
Continue
Website: www.outbackpower.com
S
Radian Inverter/Charger
FM80 Charge
Controllers
(x2)
RADIAN Series
Major Components
Radian System Products
GS8048A
Inverter/Charger
GS4048A
GSLC175-PV-120/240
GS Load Center GSLC175PV1-120/240
(both depicted)
MATE3 depicted
System Display
(with FW-MB3
and Controller
mounting bracket)
Optional OutBack Components
Communications
HUB10.3 depicted
Manager
FLEXmax 80 depicted
Charge Controller (with FW-CCB2
mounting bracket)
PV Combiner Box PV12 depicted
Remote Temperature Sensor (RTS)
FLEXnet DC Monitor (FN-DC)
Battery Bank
EnergyCell depicted
Customer-Supplied Components
Utility Grid or
AC Source
AC Generator
Main Electrical Panel (or overcurrent
device for the AC source)
Electrical Distribution Subpanel
(Load Panel)
Photovoltaic (PV) Array
IMPORTANT:
Not intended for use with
life support equipment.
Masters of the Off-Grid.™
First Choice for the New Grid.