Advertisement
Quick Links
Advertisement
Related Manuals for Nucraft Merino Casegood
Summary of Contents for Nucraft Merino Casegood
- Page 1 Merino Casegood Installation Instructions Rev B – 6/17/16...
-
Page 2: Before Beginning Installation
Before Beginning Installation • Read through the entire instruction thoroughly • A minimum of 2 people are required for this assembly • These instructions reflect typical assemblies; They may not match your specific configuration... - Page 3 Required Tools & Hardware Drill Driver #2- #3 Phillips Bit #2 Square Bit 3/8” Nut Driver Laser Level 5/16” Wrench...
- Page 4 Merino Free Standing...
- Page 5 Merino Free Standing Exploded Freestanding Desk Work Surface Lateral File Pedestal Box, Box, File Pedestal Tack Board Overhead Tower...
- Page 6 Merino U-Shape...
- Page 7 Merino U-Shape Exploded 1. Desk 2. Work Surface 3. Lateral File Pedestal 4. Box, Box, File Pedestal 5. Tack Board 6. Overhead 7. Tower 8. Access Panel 9. Corner Support 10. Bridge...
- Page 8 Merino L-Shape...
- Page 9 Merino L-Shape Exploded 1. Desk 2. Work Surface 3. Lateral File Pedestal 4. Box, Box, File Pedestal 5. Tack Board 6. Overhead 7. Overhead Hood 8. Corner Support 9. Power Option...
- Page 10 Merino T-Shape...
- Page 11 Merino T-Shape Exploded 1. Desk 2. Work Surface 3. Lateral File Pedestal 4. Box, Box, File Pedestal 5. Tack Board 6. Overhead 7. Overhead Hood 8. Access Panel 9. Tower...
- Page 12 Step 1 Installing the Credenza Locate the Pedestals and set in place. Level. Align work surface with mitered edge on pedestal(s). Attach using & If station has additional work surfaces, attach those the same way and connect using mending plates and screws Merino | 12...
- Page 13 Step 2 Attaching Corner Support Install connector pins to the work surface. Lower the work surface onto the corner support, aligning the pins with the corresponding holes in the corner support. Secure by turning the cams ½ turn clockwise.
- Page 14 Step 3 Installing Stanchions (If wall hung, skip to step 5) Loosen Loosen the stanchion channel bolts. Do not remove. Slide the stanchions in the channels. Adjust glides on the Scribe line stanchions until scribe line is Work-surface flush with work surface.
- Page 15 Step 4 Installing Tack Board & Overhead Attach the tack board using the pre installed “Z” clips on the back side. Press down to fully engage. Hang the overhead on the top of the stanchions. Adjust side to side to align with work surface.
- Page 16 Step 5 Attaching the Access Panel Align the access panel so the raffix connectors are in line with the studs. Place on studs and tighten with a phillips screwdriver by turning clockwise. Merino | 16...
- Page 17 Step 6 Installing Wall Mounted Tack Board & Overhead Ensure work surface is level. Reference numbers in the table below. Measurements “A” dimension are to the bottom of cleat. Attach wall cleats. (lag screws “B” dimension for a backed wall, toggles for non backed wall.
- Page 18 Step 7 Attaching the Sliding Hood Remove the wing nuts from the track on the back of the overhead. Lifting hood over the back of the overhead, carefully align the holes on the hood with the studs in the tracks. ...
- Page 19 Step 8 Installing Glass Desk Locate the glass top. (shipped loose) With the desk in place and properly leveled (leveling is important to ensure a proper miter alignment) place glass top in place. Use glass pods for this installation.
Need help?
Do you have a question about the Merino Casegood and is the answer not in the manual?
Questions and answers