Subscribe to Our Youtube Channel
Related Manuals for Nav TV ZEN-A2B
Summary of Contents for Nav TV ZEN-A2B
- Page 1 3950 NW 120 Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 DSP12A-A2B Ford A²B® to 12-channel Analog & Digital sound processor NTV-KIT889 ® A²B is a registered trademark of Analog Devices Inc.
- Page 2 WARNING: Due to the complexity and sensitivity of the OEM Ford A²B®, the ZEN-A2B must be 11/01/18 used with amplifiers that are grounded directly to the battery. The resistance to (true battery) NTV-DOC320 ground of the Amplifier(s) must not exceed 1 ohm, otherwise you will likely experience performance issues or damage the ZEN-A2B.
- Page 3 NTV-DOC320 DSP12A-A2B Installation 1. For ZEN-A2B installations, the factory amplifier must be removed and the ZEN-A2B can be installed into its place. If this vehicle is not amplified from factory then this interface is not needed. 2. After locating the factory amplifier, disconnect it entirely as it will no longer be in use. With the vehicle off, connect the provided ZEN-A2B harness to the (previously removed) OEM amplifier connectors (gray &...
- Page 4 11/01/18 NTV-DOC320 Multi-Color LED Status Indication LED Status Indication Solid Red A²B Active Solid Green CAN Active Green + Red (yellow) A²B + CAN Active Blue/Violet/White Amp command Blinking Red Clipping (beyond maximum digital signal level achieved) Blinking Blue PC Link via USB (updates) OEM Ford B&O amplifier connector pin out Pin # Description...
- Page 5 11/01/18 NTV-DOC320 DSP12A-A2B System Layout (analog) For ZEN-A2B installations, the factory amplifier MUST be removed or disconnected. A²B® is a registered trademark of Analog Devices Inc. P a g e...
- Page 6 11/01/18 NTV-DOC320 DSP12A-A2B System Layout (digital TOSLink) For ZEN-A2B installations, the factory amplifier MUST be removed or disconnected. A²B® is a registered trademark of Analog Devices Inc. P a g e...
- Page 7 11/01/18 NTV-DOC320 ZEN configuration: Analog Outputs (online tool) To access the ZEN online configuration tool, first connect the provided USB cable to the ZEN module, and to the PC. Open an internet browser and navigate to zen.local/ (forward slash must be present). Wait for the configuration page to load.
- Page 8 11/01/18 NTV-DOC320 ZEN Configuration: Digital Output (online tool continued) Since the digital TOSLink is a single stereo output, advanced adjustments are limited. For Digital TOSLink output, Tones and Chimes will mimic factory output on the front and rear channels. Adjust output level to suit. Once complete, select SAVE to store the settings in the ZEN module.
- Page 9 11/01/18 NTV-DOC320 DSP12A-A2B Time Alignment (Analog only) • The DSP12A-A2B features a built-in time alignment feature that can be activated on-the-fly, through an OEM menu setting. To activate the (driver) time alignment, go to Settings, Sound Settings, then choose Sound Mode. Choose Surround to use driver time alignment. No Time Alignment Driver Time Alignment ZEN Updates...
- Page 10 11/01/18 NTV-DOC320 DSP12A-A2B Technical Specifications Hardware & Software Current HW version: -- 3r0 -- Current SW version: 3.0.21 (website updater only) Compatible SW (update) OS: Windows 7 (64 bit), 8, 10 INPUT Digital Input A²B Twisted Pair OUTPUT Digital Outputs: TOSLink Digital Outputs supported: 24bit/48kHz...
- Page 11 11/01/18 NTV-DOC320 Notes • With A²B, if the power or (A2B) is ever removed from the ZEN module, the vehicle will require a CAN reset once or twice to regain normal OEM functionality (chimes, etc). CAN-reset procedure: 1. Turning off ignition 2.
Need help?
Do you have a question about the ZEN-A2B and is the answer not in the manual?
Questions and answers