Advertisement
Quick Links
3950 NW 120
The BMW-EVO kit interfaces 2 video inputs (including a backup camera) to the factory media
screen in select 2017 BMWs with the NEW GUI (NON-TOUCH SCREEN). This interface generates
steering-based guidelines while in reverse for added convenience. NOTE: the touch-screen
models with this OEM system are not compatible.
5 Series LVDS
extension cable
with coupler:
NTV-CAB121
Optional extension cables
7 Series LVDS
extension cable
with coupler:
NTV-CAB122
:
Agreement
End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
th
Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760
www.nav-tv.com
info@nav-tv.com
BMW-EVO KIT
NTV-KIT804
Overview
Kit Contents
BMW-EVO Interface
Power/CAN Harness
BHM
11/20/17
NTV-DOC290
Connector
LVDS Video
cable
Remote
(menu control)
1 |
P a g e
Screen
IR Eye
Harness
Advertisement
Related Manuals for Nav TV BMW-EVO KIT NTV-KIT804
Summary of Contents for Nav TV BMW-EVO KIT NTV-KIT804
- Page 1 11/20/17 NTV-DOC290 3950 NW 120 Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com Screen BMW-EVO KIT Connector NTV-KIT804 Overview The BMW-EVO kit interfaces 2 video inputs (including a backup camera) to the factory media screen in select 2017 BMWs with the NEW GUI (NON-TOUCH SCREEN). This interface generates steering-based guidelines while in reverse for added convenience.
- Page 2 11/20/17 NTV-DOC290 Interface Connectors Power/CAN Expansion board RGB INPUT Digital RGB input (HDMI Adapter) OUOUT control (optional) OUOUT Infrared LCD OUT (Provided LCD IN (LVDS from Dip Switches OEM screen) Receiver LVDS Cable) (see below) Dip Switch settings* Dip SW: NO NAV KEEP KEEP...
- Page 3 11/20/17 NTV-DOC290 BMW-EVO Interface Installation (5 Series example) 1. The BMW-EVO intercepts two OEM plugs in two locations: the iDRIVE knob and the screen. You must gain access to both places for proper installation. a. Access the rear of the screen by removing the dashboard panel (clips only) and then removing (2x) Torx T20 screws securing the screen to the sub-dash.
- Page 4 11/20/17 NTV-DOC290 4. Replace the lower dash panel (with iDrive knob) back to sub-dash. 5. Disconnect the OEM screen LVDS video cable and connect it to the port on the BMW12-N labeled ‘LCD-IN’. NOTE: If purchased (separately), use the LVDS extension cable (with 5 Series 7 Series coupler) from the OEM screen...
- Page 5 11/20/17 NTV-DOC290 Menu Adjustments Before you start: • The IR-Eye must be connected • Make sure the car’s ignition is on and radio is on • You must be in Reverse Camera mode AUX Video mode (see Return (AUX VID below): •...
- Page 6 11/20/17 NTV-DOC290 Adding Optional HD-LINK Adapter (HDMI Input) Follow the instructions below when adding the HDMI adapter (HD-LINK) to enable HDMI input to the OEM screen: 1. Put dip switch #1 in the DOWN position. 2. Activate the ‘NAV INPUT’ by pressing the ‘MENU’...
- Page 7 11/20/17 NTV-DOC290 Green Trigger wire setup This module includes a green input wire for analog triggering of either the Reverse camera input or the ‘AVIN’ input (yellow RCAs), selectable through the AV menu. This allows for adding multiple cameras through the use of an SVS-6 switcher, etc. Follow the steps below adjust this feature. NOTE: by default, the green wire will trigger the Reverse camera input RCA.
- Page 8 11/20/17 NTV-DOC290 BMW-EVO Installation Diagram Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only.
- Page 9 11/20/17 NTV-DOC290 BMW-EVO Operation • Once all connections are made and dip switches are set properly, placing the vehicle in reverse will display the connected camera with dynamic guidelines for convenience. • Additionally, see below for AUX/Front camera/HDMI activation using factory buttons. Hold (3 sec): Activate AUX/Front Camera video input...
Need help?
Do you have a question about the BMW-EVO KIT NTV-KIT804 and is the answer not in the manual?
Questions and answers