Section 3 - Programming - DoorKing 1837 Owner's Manual

90 series telephone entry and access control systems

Hide thumbs Also See for 1837:

Installation & owner's manual (76 pages)

Owner's manual (76 pages)

Installation and owner's manual (36 pages)

Table of Contents

We strongly suggest that you read these programming instructions in their entirety before beginning any programming of

this telephone entry system.

IMPORTANT!

Many of the advanced features available with this telephone entry system CANNOT be programmed from the

system keypad. These advanced features include relay hold open time zones, security levels, elevator control options and

programming via the internet using DKS servers. If any of these advanced features are used, the system MUST be programmed

with a PC using the DoorKing Remote Account Manager for Windows software, VERSION 6.4.i or higher. Refer to the software

help screen for more information on these advanced features.

3.1 General Programming Information

The DoorKing PC Programmable Telephone Entry System is primarily programmed by

using the DoorKing Remote Account Manager for Windows software. However, the

system can also be partially programmed from the keypad on the front of the entry

system.

Programming the entry system can also be preformed off-site using a user supplied

PC with the DKS software loaded on it. Make sure the RING pin jumper is in place on

the circuit board, which was factory installed. See section 4.5 for more information.

The PC programmable telephone entry systems have three relays on the circuit board, all of which are programmable for any

function required. These relays are designated as Relay 0 (R 0), Relay 1 (R 1), and Relay 2 (R 2). If Expansion boards are used

with this system, it is very important that you understand the function of these three relays. The wiegand input auxiliary

terminals (also the Expansion board input terminals) can only cause R 1 or R 2 to activate. Wiegand input devices CANNOT

cause R 0 to activate. Therefore, if Tracker Expansion boards are used with this system, R 0 MUST be designated as the

PRIMARY relay, and R 1 and R 2 are then designated as Tracker Expansion board command (CMD) relays with R 2 controlling

Expansion boards 1 through 8 (system relays 3-10), and R 1 controlling Expansion boards 9 through 16 (system relays 11-18).

The PRIMARY relay is the relay that a resident activates from their telephone after receiving a call from a visitor. When Tracker

Expansion boards or other wiegand devices are used with the system, be sure that R 0 is programmed to respond to the tone

open number (typically 9), the postal switch input, and the rotary dial 9 function.

3.1.1 Programming from a PC

Prior to programming the system with a PC and the DoorKing Remote Account Manager for Windows Software, there is certain

information that you must know and must program into the system before the computer can communicate with the system. See

next page section 3.2 to set-up the telephone entry system for PC programming. Programming the system with a PC may be

accomplished by sections 2.4 and 2.5 Connection Options for all layouts and additional hardware that is needed for each. All

options require the DoorKing Remote Account Manager for Windows Software VERSION 6.4.i or higher.

3.1.2 Programming from the Telephone Entry System Keypad

Follow the programming instructions as described in each section of this manual. The system will prompt you with short tones

(beep) when programming steps have been followed correctly, and with a long tone (beeeeeep) when the programming step is

ended. The LCD display will also assist you in viewing the information that you are programming. It is highly recommended that

you complete the resident information in section 7 in back of this manual prior to programming from the system keypad. This

will provide you with the information needed to complete the manual programming sequence (section 3.2). When programming

from the system keypad, after each programming step is performed correctly, a short tone (beep) will be heard. When the

programming session is ended, a long tone (beeeeeep) will be heard.

Important Note:

Relay hold open time zones, security levels, holiday schedules, anti-pass back IN / OUT tables, anti-pass back

re-sync schedules and elevator control features CANNOT be programmed from the system keypad. These advanced features

can only be programmed from a PC using the DoorKing Remote Account Manager Software.

1835-067-A-9-18