Installation, Operation and Parts Manual EE-6215E IMPORTANT NOTES Before start up, connecting and operating EAE products, it is absolutely essential that the operating instructions/owner’s manual and, in particular the safety instructions are studied carefully. By doing so you can eliminate any uncertainties in handling EAE products and thus associated safety risks up front; something which is in the interest of you own safety and will ultimately help avoid damage to the device. When an EAE product is handed over to another person, not only the operating instructions but also the safety instructions and information on its designated use must be handed over to the person. By using the product you agree the following conditions: Copy right The enclosed instructions are the property of EAE or its supplier, and are protected against duplication and reproduction by copyright laws, international agreements, and other domestic legislation. The reproduction or disclosure of instructions or an extract thereof is prohibited and offenders are liable to prosecution; EAE reserves the right or initiates criminal proceedings and asserts claims for damages in the event of infringements. Warranty The use of non‐approved hardware will result in a modification of our products and thus to the exclusion of any liability or warranty, even if such hardware has been removed again in the interim. It is not permissible to make any changes to our products and these are not only to be used together with genuine accessories and genuine replacement parts. Otherwise any warranty claims will be invalid. Liability The liability of EAE is limit to the amount that the customer has actually paid for this product. This exclusion of liability does not apply to damages caused through willful misconduct or gross negligence on the part of EAE. ...
Installation, Operation and Parts Manual EE-6215E IMPORTANT NOTES ............................ 2 SAFETY NOTES .............................. 4 1.1 Operation of lifting platforms .......................... 4 1.2 Checking of the lifting platforms .......................... 4 1.3 Important safety notices ............................ 5 1.4 Warning labels ............................... 6 1.5 Potential safety risks .............................. 7 1.6 Noise level ................................ 7 PACKING, STORAGE AND TRANSPORTATION ..................... 8 2.1 The lift was dismantled into the following 3 parts for transportation .............. 8 ...
Installation, Operation and Parts Manual EE-6215E SAFETY NOTES 1.1 Operation of lifting platforms This lift is specially designed for lifting motor vehicles. Users are not allowed to use it for any other purposes. The applicable national regulations, laws and directives must be observed. Only users aged 18 or above who have been instructed on how to operate the lifting platform and have proven their ability to do so to the owner are to be entrusted with unsupervised operation of lifting platforms. The task of operating the lifting platforms must be granted in writing. Before loading a vehicle onto the lift, users should study the original operation instructions and familiarize themselves with the operating procedures in several trial runs. Lift vehicle within the rated load. Don’t attempt to raise vehicles with excessive weight. 1.2 Checking of the lifting platforms Checks are to be based on the following directives and regulations: Basic principles for testing lifting platforms The basic health and safety requirements stipulated in the directive 2006/42/EC Harmonized European standards The applicable accident prevention regulations The checks are to be organized by the user of the lifting platform. The user is responsible for appointing an expert or qualified person to perform checking. It must be ensure that the person chosen satisfies the requirements. The user bears special responsibility if employees of the company are appointed as experts or qualified persons. 1.2.1 Scope of checking Regular checking essentially involves performing a visual inspection and a functional test. This includes checking the condition of the components and equipment, checking that the safety systems are complete and functioning properly and that the inspection log book is ...
Installation, Operation and Parts Manual EE-6215E rules of engineering to be able to check and give an expert option on lifting platforms. 1.3 Important safety notices 1.3.1 Recommend for indoor use only. DO not expose the lift to rain, snow or excessive moisture. 1.3.2 Only use this lift on a surface that is stable and capable of sustaining the load. Do not install the lift on any asphalt surface. 1.3.3 Read and understand all safety warnings before operating the lift. 1.3.4 Do not leave the controls while the lift is still in motion. 1.3.5 Keep hands and feet away from any moving parts. Keep feet clear of the lift when lowering. 1.3.6 Only these properly trained personnel can operate the lift. 1.3.7 Do not wear unfit clothes such as large clothes with flounces, tires, etc., which could be caught by moving parts of the lift. 1.3.8 To prevent evitable incidents, surrounding areas of the lift must be tidy and with nothing unconcerned. 1.3.9 The lift is simply designed to lift the entire body of vehicles, with its maximum weight within the lifting capacity. 1.3.10 Always insure the safety locks are engaged before any attempt to work near or under the vehicle. Never remove safety related components from the lift. Do not use if safety related components are damaged or missing. 1.3.11 Do not rock the vehicle while on the lift or remove any heavy component from vehicle that may cause excessive weight shift. 1.3.12 Check at any time the parts of the lift to ensure the agility of moving parts and the performance of synchronization. Ensure regular maintenance and if anything abnormal occurs, stop using the lift immediately and contact our dealers for help. 1.3.13 Lower the lift to its lowest position and do remember to cut off the power source when service finishes. 1.3.14 Do not modify any parts of the lift without manufacturer’s advice. 1.3.15 If the lift is going to be left unused for a long time, users are required to: a. Disconnect the power; b. Empty the oil tank; c. Lubricate the moving parts with hydraulic oil. WARNING:The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. ...
Installation, Operation and Parts Manual EE-6215E 1.4 Warning labels All safety warning labels are clearly depicted on the lift to ensure that the operator is aware of and avoid the dangers of using the lift in an incorrect manner. The labels must be kept clean and they have to be replaced if detached or damaged. Please read carefully the meaning of each label and memories them for future operation. ...
Installation, Operation and Parts Manual EE-6215E 1.5 Potential safety risks 1.5.1 Main voltage nsulation damage and other faults may result in accessible components being live. Safety measures: Only ever use the power cord provided or a tested power cord. Replace wires with damaged insulation. Do not open the operating unit. 1.5.2 Risk of injury, danger of crushing In the event of excessive vehicle weight, incorrect mounting of the vehicle or on removing heavy object, there is a risk of the vehicle falling off or tipping up. Safety measures: The lift is only ever to be employed for the intended purpose. Carefully study and heed all the information given in Section 1.4. Observe the warning notices for operation. 1.6 Noise level Noise emitted during operating the lift should be less than 70dB. For your health consideration, it is suggested to place a noise detector ...
Installation, Operation and Parts Manual EE-6215E PACKING, STORAGE AND TRANSPORTATION Packing, lifting, handling, transporting operations must be performed only by experienced personnel with appropriate knowledge of the lift and after reading this manual. 2.1 The lift was dismantled into the following 3 parts for transportation Name Packed by Dimension Weight Quantity Lift Steel brackets 2860*660*930 908kg 1 Extending post Bubble film 1800*400*430 145kg 1 Power unit Carton 850*250*350 24kg 1 2.2 Storage The packs must be kept in a covered and protected area in a temperature range 0f ‐10℃to +40℃. They must not be exposed to direct ...
Installation, Operation and Parts Manual EE-6215E PRODUCTS DESCRIPTIONS 3.1 General descriptions This lift is mainly composed of posts, carriages, lifting arms, cylinders and hydraulic power unit. It is driven by electro‐hydraulic system. The gear pump delivers hydraulic oil to oil cylinders and pushes upwards its piston. The piston drives to raise the carriage and the lifting arms. During lifting process, the mechanical safety locking system ensures no slipping in case of failure hydraulic system. 3.2 Construction of the lift 3.3 Technical data Full rise time Full rise time Model Lifting capacity Full rise (3.5kW motor ) ...
Installation, Operation and Parts Manual EE-6215E 3.5 Safety devices descriptions POS. Name Function 1 Steel cable Ensure sure the synchronization for both carriages 2 Mechanical safety catch Catch the carriages in case of hydraulic failure 3 Limit switch Stop rising movement at maximum safety height 4 Arm locking unit Ensure the lifting arms are locked and avoid being swinging during lifting process 5 Lifting pad Safe rubber contact with the wheel base of lifted vehicle 6 Fender ...
Installation, Operation and Parts Manual EE-6215E INSTALLATION INSTRUCTIONS 4.1 Preparations before installation 4.1.1 Space requirements. Indoor installation only. Refer to 3.4 for the dimensions of the lift. There must also be a clearance of at least 1 meter between the lifting platform and fixed elements (e.g. wall) in all lifting positions. There must be sufficient space for driving vehicles on and off. 4.1.2 Foundations and connections The user must have the following work performed before erecting the lift. Construction of the foundation following consultation with the manufacturer’s customer service or an authorized service agent. Routing of the wiring to the installation location. The user must provide fuse protection for the connection. Electrical system 2 connection must be done by licensed technicians. Requirements for power supply cable of the installation site: at least 2.5mm 2 ...
Installation, Operation and Parts Manual EE-6215E 4.3 General Installation Steps Step 1: Remove the packaging, take out the carton for accessories. Step 2: Firstly, put something supporting between the two posts or suspend one of the posts by a crane and then remove the bolts from the packing frame. Attention:Please pay special attention not to let the post fall down for it may cause casualty or bring damages to the accessories fixed in the post. Step 3: When the first post has been taken away, place something supporter under the second post and then remove the bolts from the packing frame. Step 4: Connect extending posts and cross beams 1. Firstly fix the extending post onto the body posts. This is only necessary when your lift is ordered with extending posts. ...
Page 14
Installation, Operation and Parts Manual EE-6215E 2. Connect the beams and fix the roof protection bumper Step 5: Fix the standing position for the two posts. 1. Unfold the package and decide on which post the power unit will be mounted. 2. Ascertain the position for the two posts with chalk and tape measure and draw an outline of the two base plates on the ground. Step 6: Connect cross beam. Make the posts face to each other and the distance between the posts equals to the length of the overhead crossbeam. Fix the beam with the posts by screw M12×30. ...
Page 15
Installation, Operation and Parts Manual EE-6215E Step 7: Erect and secure the post. 1. Use suitable means to raise the lifting carriage to the first latching position. All the mounting holes in the base plate are then accessible. Make sure the locking pawl is engaged. 2. Check the position of the base plates again. 3. Drill the mounting holes. Remove the drilling dust from the hole. 4. Use a spirit level to check the vertical alignment of the lifting posts. If necessary, place equalizing plates under the base plates. The equalizing plates must be of the same length as the side of the base plate resting on them. Otherwise the load of the base plate will not be transferred evenly to the foundation. 5. Erect and secure the other post similarly. ...
Page 16
Installation, Operation and Parts Manual EE-6215E Step 9: Connect oil hoses. 1. Mount the power unit onto the power side post. 2. Connect oil hoses according to the following diagram. NOTE: make sure the connectors and hose are clean. ...
Page 17
Installation, Operation and Parts Manual EE-6215E Step 10: Fix the electromagnets. Step 11: Connect electrical system. Refer to electrical connection diagram. 1. Mount the control box on to the power side post. ...
Page 18
Installation, Operation and Parts Manual EE-6215E 2. Connect the limit switch fixed inside the power‐side post. 3. Connect the limit switch fixed at the cross beam. ...
Page 19
Installation, Operation and Parts Manual EE-6215E 4. Connect wires of electromagnet 5. Connect soloenoid valve,motor wire and power suppply cable . ...
Page 20
Installation, Operation and Parts Manual EE-6215E Step 12: Install lifting arms. Connect the lifting arm and the carriage. The arm pin shafts must be greased at the installation Ensure the arm lock can engage and release effectively. . Attention: Install Lifting arms and fix feet protection bars ONLY after the complete assembly has been erected and anchored. Step 13: Fill with hydraulic oil. CLEAN AND FRESH OIL ONLY. DON’T FILL THE TANK COMPLETELY FULL. Lift must be fully lowered before changing or adding hydraulic oil. Usually it needs 13 liters of hydraulic oil. Firstly, fill about 10Ls into the oil tank to run the lift up and down for 2 or 3 times. After running the lift for several cycles, add more oil if necessary to raise lift to full height. Note:It is suggested using NO.46 hydraulic oil when average temperature of the location is above 18 degree Celsius and using NO.32 hydraulic oil when temperature is below 18 degree Celsius. Change the oil 6 months after initial use and change once per year thereafter. Step 14: Trial running. Get familiar with lift controls by running the lift through a few cycles before loading vehicle on lift. This step is of particular ...
Page 21
Installation, Operation and Parts Manual EE-6215E Check the synchronization of both lifting carriages. Ensure the synchronization by adjusting the balance steel cables at both sides are of the same tightness. This could be judged by the sound emitted during lifting process. If the lift doesn't raise, the motor may turn in the wrong direction. In such event, interchange wires U, V in the connection box. Step 15: Fix feet protection fenders, chain protection clothes, electro‐magnet protection covers, door‐opening protections and lifting trays. ...
Installation, Operation and Parts Manual EE-6215E 4.4 Items to be checked after installation. S/N Check items YES NO √ 1 Screw torque of expansion bolts : 60‐80N•m; √ 2 Rising speed ≥20mm/s; √ 3 Noise with rated load ≤75db; √ 4 Grounding resistance: not bigger than 4Ω; √ 5 Height difference of the two carriages ≤5mm; √ 6 Mechanical locks are robust and synchronized when running with rated load ; √ 7 If the control button works as “hold to run”? √ 8 If limit switches work well? √...
Installation, Operation and Parts Manual EE-6215E OPERATION INSTRUCTIONS 5.1 Precautions 5.1.1 Check all the joints of oil hose. Only when there is no leakage, the lift can start work. 5.1.2 The lift, if its safety device malfunctions, shall not be used. 5.1.3 The machine shall not lift or lower an automobile if its center of gravity is not positioned midway of the rising platforms. Otherwise, the manufacturer as well as the dealers will not bear any responsibility for any consequence resulted thereby. 5.1.4 Operators and other personnel concerned should stand in a safety area during lifting and lowering process. 5.1.5 When platforms rise to the expected height, turn off the power to prevent any wrong operation done by unconcerned people. If necessary, lock the switch with a padlock. 5.2 Flow chart for operation Raising Lowering Start Start Turn on the power switch Turn on the power switch Push the DOWN button Push the UP button The lift is lowered ...
Installation, Operation and Parts Manual EE-6215E 5.3 Operation instructions Pos. Name Function QS Power switch Control main power HL Power indicator Show if electricity is connected SB1 UP button Control the rising movement SB2 Safety lock button Engage the mechanical safety lock SB3 DOWN button Control the lowering movement ...
Installation, Operation and Parts Manual EE-6215E TROUBLE SHOOTING ATTENTION: If the trouble could not be fixed by yourself, please do not hesitate to contact us for help. We will offer our service at the earliest time we can. Troubles could be judged and solved much faster if more details or pictures could be provided. TROUBLES CAUSES SOLUTIONS Abrasion exists on insider surface of the posts. Grease the inside of the post. Abnormal noise Trash in the post. Clear the trash Loose wire connection Check and make a good connection. Motor does not run and will not Blown motor. Replace it. rise Damaged limit switch or its wire connection is loose. Adjust or replace the limit switch. The motor run reversely. Check the wire connection. Overflow valve is not well screwed up or jammed. Clean or make adjustment Damaged gear pump. Replace it. Motor runs but will not raise ...
Installation, Operation and Parts Manual EE-6215E MAINTENANCE Easy and low cost routine maintenance can ensure the lift work normally and safely. Following are requirements for routine maintenance. Follow the below routine maintenance schedule with reference to the actual working condition and frequency of your lift. S/N Components Methods Period Push the UP button to raise the lifting arms and check if four swing 1 Swing arm locking units Every day arms are locked into position. Add grease in case necessary. Inspect the pads and clean off any objects that may cause sliding or ...
Page 27
Installation, Operation and Parts Manual EE-6215E S/N Components Methods Period Check the synchronization of both carriages and adjust the tightness 8 Steel cables Every day of the cable if desynchronization is unacceptable. Bushing of the upside pulley Lubricate the bushing with NO.1 lithium based grease. 9 Every 3 months and circlip of the shaft Check if the circlip is in its original position. Lubricate the cables with NO.1 lithium based grease. 10 Steel cables Change with new steel cables every 3 years or ten single wires have Every 3 months broken. Running track inside the ...
Installation, Operation and Parts Manual EE-6215E Annex 1, Floor plan Indoor installation only. There must also be a clearance of at least 1 meter between the lifting platform and fixed elements (e.g. wall) in all lifting positions. There must be sufficient space for driving vehicles on and off. C20/25 concrete base with strength more than 3000psi, Minimum thickness of 200mm. Surface: Horizontal and even (Gradients max. 0.5 %) Newly built concrete ground must be older than 20days. In mm. ...
Installation, Operation and Parts Manual EE-6215E Annex 2, Electrical diagrams and parts list (Note: For the specific requirements on voltage, the actual voltage of your lift may differ with the following diagram) ...
Page 30
Installation, Operation and Parts Manual EE-6215E ...
Page 31
Installation, Operation and Parts Manual EE-6215E SQ1: roof protection limit switch SQ2: max height limit switch YA1‐YA4: electromagnet YV : solenoid unloading valve uncrossed wire ...
Installation, Operation and Parts Manual EE-6215E Annex 3, Hydraulic diagrams and parts list 1.oil tank 2.oil filter 3.gear pump 4.coupling 5.aluminium motor 6.hydraulic block 7.cushion valve 8.overflow valve 9.single way valve 10.solenoid unloading valve 11.flow control valve 12.tank cover 13.composite connector 14.oil cylinder Seal rings CODE Name ...
Page 34
Installation, Operation and Parts Manual EE-6215E Pos. CODE Name Specification Qty 1 Hydraulic power unit 2.2kW or 3.5kW 1 2 207103025 Composite washer M14 1 3 310101028 Shift connector G1/4M14x1.5,M14x1.5 with protective cap 1 4 624001042B Rubber oil hose DN8 ,L=400 1 ...
Page 35
Installation, Operation and Parts Manual EE-6215E ...
Page 36
Installation, Operation and Parts Manual EE-6215E Pos. CODE Name Specification Qty 1 330405001 Oil tank 10L 1 2 330101063B Hydraulic block (E) YF‐2D 1 3 330308006 Solenoid unloading valve DHF06‐220H/DC24 1 4 330304001 Overflow valve EYF‐C 1 5 330302001 Single way valve ...