SelectBlinds Vertical Blinds Installation Instructions

Choose the Correct
Please Follow These Installation Instructions
Fastener
You will need a pencil, tape measure, drill, screwdriver, pliers and appropriate fasteners.
Self drilling hex head for aluminum
Choose the Correct Fastener
Step 1
Rawl plug and sheet metal screw for concrete
No. 8 sheet metal screws for wood and aluminum
Included Fasteners
Molly bolt for dry wall
Please Follow These Installation Instructions
Toggle bolt for lathe and plaster or drywall
You will need a pencil, tape measure, drill, screw driver, pair of pliers,
and the appropriate fasteners. (see page 4)
Packing List
Outside Mount
1
6
3
CAUTION! If you have purchased PVC louvers, store them on a at, level surface until they are installed.
Figure 1
Vertical Blinds
Installation
Instructions
Removing a
Louver
L ocate which side of the
carrier had the actual hook.
Insert thumb between louver
and that side, as shown,
and pull down
the louver.
Inside Mount
8
Applicable:
7
4
5
10
2
9
Figure 2 Figure 3
Choose the Correct
Choose the Correct
Fastener
Fastener
Self drilling hex head for aluminum
Self drilling hex head for aluminum
R awl plug and sheet metal screw for concrete
Rawl plug and sheet metal screw for concrete
No. 8 sheet metal screws for wood and aluminum
No. 8 sheet metal screws for wood and aluminum
Molly bolt for dry wall
Toggle bolt for lathe and plaster or drywall
Toggle bolt for lathe and plaster or drywall
1. Headrail with Bead Chain
Ceiling Mount
and Cord
2. Wall Brackets
3. Mounting Clips
Packing List
Packing List
If
4. Cord Weight
5. Tension Pulley
6. PVC Louvers
7. Valance
8. Valance Returns
9. Valance Clips
1
1
10. Valance Corners
6
6
Place the first bracket directly over the corner of
the window with a maximum space of 30" between
brackets. Adjust the bracket so louvers clear all
obstructions.
3
3
CAUTION! If you have purchased PVC louvers, store them on a at, level surface until they are installed.
CAUTION! If you have purchased PVC louvers, store them on a at, level surface until they are installed.
Rev. 4/04
Set mounting clips with a maximum space of 30"
apart from each other. Allow a minimum of 1/2"
clearance above sill or carpet.
Choose the Correct
Fastener
Self drilling hex head for aluminum
Heavy Duty Track
Rawl plug and sheet metal screw for concrete
No. 8 sheet metal screws for wood and aluminum
Toggle bolt for lathe and plaster or drywall
Alternate Fasteners
(not included)
Packing List
Step 2
Step 1
Molly bolt for dry wall
Outside Mount
(Figure 1)
Outside Mount
( gure 1)
1
6
Standard wall brackets
The standard bracket
are adjustable and provide
is adjustable between
1/2" and 1 1/2" wall
1/2" and 1-1/2" wall
clearance.
clearance.
Determine the height for
Find the height for
the top of the bracket
the top of the bracket
(measured from the floor)
adding 1/2" to the blind
8 (as measured from the
8
height including the head-
oor) by adding 1/2" to
rail. When installed, lou-
the blind height as pro-
3
wall bracket vers will clear the floor
vided on the headrail.
by 1/2".
When installed, louvers
4
4 will clear the oor by 1/2".
CAUTION! If you have purchased PVC louvers, store them on a at
Place the rst bracket directly over the corner of the
5
5
window with a max. of 30" between brackets. Adjust
the length of the bracket so that the louvers clear all
obstructions.
2
Inside or Ceiling Mount 2
Inside or Ceiling Mount 9
9
(Figures 2 or 3)
(Figure 2&3) (for valance, see inside)
Use mounting clips to
Use clip brackets mounted
secure headrail on ceiling
directly to ceiling or head.
or inside mounts.
The center of the clip
The center of the mount-
bracket equals the center
ing clip aligns with the
of the louver hook. Locate
center of the louver carrier
stem. Position the screws the screw a minimum of
a minimum of 2 1/4" in
2-1/4" in front of the
mounting clips
front of the window frame
window frame or any
or any projection.
projection.
Locate clip #3 from each of the track with a maxi-
mum of 30" between clips. Allow a minimum of 1/2"
clearance above sill or carpet
Removing a
Removing a
Louver
Louver
L ocate which side of the
Locate which side of the
Molly bolt for dry wall
carrier had the actual hook.
carrier had the actual hook.
Insert thumb between louver
Insert thumb between louver
and that side, as shown,
and that side, as shown,
and pull down
and pull down
the louver.
the louver.
8
4
1. Headrail with Bead Ch
1. Headrail with Bead
and Cord
and Cord
2. Wall Brackets
2. Wall Brackets
5
3. Mounting Clips
3. Mounting Clips
by
If
If
4. Cord Weight
Applicable:
4. Cord Weight
Applicable:
5. Tension Pulley
5. Tension Pulley
6. PVC Louvers
6. PVC Louvers
2
7. Valance
7. Valance
8. Valance Returns
8. Valance Returns 9
9. Valance Clips
9. Valance Clips
10. Valance Corners
10. Valance Corners
7
7
10
10
R
L
L
c
I
a
a
t