Table Of Contents - Magnetrol Thermatel TA2 Installation And Operating Manual

Thermatel

Table of Contents

1.0 F fieldbus
OUND TION
1.1 Description ...............................................................4
1.2 Device Configuration................................................5
1.2.1 F
OUNDATION
1.3 Link Active Scheduler (LAS).....................................6
2.0 Quick Start Installation
2.1 Probe Installation ......................................................6
2.2 Wiring ......................................................................7
2.3 Configuration ...........................................................7
3.0 Installation
3.1 Unpacking ................................................................8
3.2 Electrostatic Discharge (ESD) Handling Procedure .....8
3.3 Installation ................................................................9
3.3.1 Electronics......................................................9
3.3.2 Probe/Flow Body............................................9
3.4 Wiring ....................................................................11
3.4.1 Power and Signal Connection ......................11
3.4.2 Ground Connection.....................................11
3.4.3 Remote Electronics.......................................12
3.4.3.1 Probe Wiring ........................................12
3.5 Configuring the Transmitter....................................13
3.5.1 Initialization .................................................13
3.5.2 Operator Keypad..........................................14
3.5.2.1 Menu Traversal Mode............................14
3.5.2.2 Item List Selection ................................14
3.5.2.3 Numeric Entry......................................15
3.5.2.4 Character Data Entry Mode..................15
3.5.2.5 Increment/Decrement Digit Mode........16
3.5.3 Password.......................................................16
3.5.4 Run Mode....................................................18
3.5.5 Measured Values...........................................18
3.5.6 Basic Configuration Menu ...........................20
3.5.7 I/O Configuration Menu .............................21
3.5.8 Totalizer .......................................................21
3.5.9 Advanced Configuration Menu ....................23
3.5.10 Device Information ......................................25
3.5.11 Diagnostics Menu ........................................26
3.5.12 Factory Configuration ..................................30
3.5.13 Probe Parameters ..........................................31
3.5.14 Calibration Parameters .................................32
3.5.15 Gas Parameters .............................................33
3.5.16 Air Equivalency Calibration .........................34
4.0 Function Blocks
4.1 Overview.................................................................35
4.1.1 Universal F
Block Parameters ..........................................35
4.2 Resource Block........................................................36
4.2.1 Additional Resource Block Parameters .........39
4.2.2 Manufacturer-Specific Parameters ................40
4.3 Transducer Block.....................................................41
4.3.1 Transducer Block Parameters........................41
Enhanced Model T 2 Transmitter
®
Overview
™
fieldbus Revision Table ..........5
™
fieldbus
™
OUNDATION
4.4 Analog Input Block.................................................42
4.4.1 AI Block Parameters .....................................42
4.5 PID Block ...............................................................44
4.5.1 PID Block Parameters ..................................45
4.6 Integrator Block ......................................................47
4.6.1 Integrator Block Parameters .........................48
4.7 Local Display of Function Block Values ..................50
5.0 Diagnostic Parameters
5.1 Simulation Feature ..................................................52
5.1.1 Removing the Simulation Jumper ................52
5.2 Troubleshooting ......................................................52
5.2.1 Error Messages .............................................54
5.2.1.1 Fault Messages.......................................55
5.2.1.2 Warning Messages .................................56
5.2.1.3 Information Message.............................56
5.2.1.4 Device Status Parameter
in the Transducer Block ........................57
5.3 Diagnostics Test ......................................................58
5.3.1 Heater Setting ..............................................58
5.3.2 Zero Power Test............................................58
5.3.3 Calibration Verification Procedure ...............58
6.0 Maintenance
6.1 Circuit Board Replacement .....................................60
6.2 Probe Replacement .................................................61
6.3 Replacement Calibration.........................................62
6.3.1 RTD Calibration..........................................62
6.3.2 Set Point Adjustment ...................................62
6.4 Flow Recalibration ..................................................62
7.0 Reference Information
7.1 Description .............................................................64
7.2 Theory of Operation...............................................65
7.3 Display Module ......................................................66
7.4 Agency Approvals....................................................67
7.5 Replacement Parts...................................................68
7.6 Specifications ..........................................................70
7.6.1 Performance .................................................70
7.6.2 Transmitter ..................................................70
7.6.3 Probe............................................................70
7.6.4 Flow Body....................................................70
7.6.5 Physical ........................................................71
7.7 Model Numbers......................................................73
7.7.1 Transmitter...................................................73
7.7.2 Insertion Probe.............................................74
7.7.4 Flow Body....................................................75
7.7.5 Connecting Cable ........................................76
7.8 References ...............................................................77
ppendix - Transducer Block Parameters .................77
ppendix B....................................................................79
Glossary .........................................................................82
Flow pplication Questionnaire....................................83