Summary of Contents for Renesas RTK79210**B00000BE
Page 1
All information contained in these materials, including products and product specifications, represents information on the product at the time of publication and is subject to change by Renesas Electronics Corp. without notice. Please review the latest information published by Renesas Electronics Corp.
Page 2
11. This document shall not be reprinted, reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics.
Page 3
General Precautions in the Handling of Microprocessing Unit and Microcontroller Unit Products The following usage notes are applicable to all Microprocessing unit and Microcontroller unit products from Renesas. For detailed usage notes on the products covered by this document, refer to the relevant sections of the document as well as any technical updates that have been issued for the products.
Page 4
As a result, this equipment, including all accessories, must not be disposed of as household waste but through your locally recognised recycling or disposal schemes. As part of our commitment to environmental responsibility Renesas also offers to take back the equipment and has implemented a Tools Product Recycling Program for customers in Europe.
Page 5
(connectors, switches, etc.) The following documents apply to the RZ/A2M group. Make sure to refer to the latest versions of these documents. The newest versions of the documents listed may be obtained from the Renesas Electronics Web site. document Type Description Document Title Document No.
Page 6
Abbreviations Abbreviation Full Form ACIA Asynchronous Communications Interface Adapter bits per second Cyclic Redundancy Check Direct Memory Access DMAC Direct Memory Access Controller Global System for Mobile Communications Hi-Z High Impedance IEBus Inter Equipment Bus Input/Output IrDA Infrared Data Association Least Significant Bit Most Significant Bit Non-Connect...
RZ/A2M SUB Board RTK79210XXB00000BE 1. Overview Overview Overview The RTK79210XXB00000BE is a SUB board for use with the RZ/A2M CPU board. In combination with the RZ/A2M CPU board RTK7921053C00000BE, RZ/A2M functionality and performance can be evaluated, and application software can be developed and evaluated in advance. The RTK79210XXB00000BE has the following features. ●...
RZ/A2M SUB Board RTK79210XXB00000BE 1. Overview Configuration Figure 1.1 shows an example of system configuration using RTK79210XXB00000BE. DC 5V output AC adapter RZ/A2M CPU board RTK7921053C00000BE * Backlight LVDS CN14 CN16 RZ/A2M 9 10 NAND RZ/A2M SUB board CMOS camera RTK79210XXB00000BE VDC6 Type-A...
RZ/A2M SUB Board RTK79210XXB00000BE 1. Overview Layout of Components Figure 1.4 - Figure 1.5 show the layout of RTK79210XXB00000BE main components. Figure 1.4 RTK79210XXB00000BE Layout of Components (C Side Top View) R20UT4398EJ0100 Rev.1.00 2018.10.11...
Page 15
RZ/A2M SUB Board RTK79210XXB00000BE 1. Overview Figure 1.5 RTK79210XXB00000BE Layout of Components (S Side Top View) R20UT4398EJ0100 Rev.1.00 2018.10.11...
Page 16
Table 1.2 Main Components on RTK79210XXB00000BE (1) IC Component Component Name Type (Manufacturer) Recommended Optional Number Components Audio CODEC WM8978CGEFL/V (Cirrus) USB serial converter IC R5F10JBCANA#U0 (Renesas) U27, U28 Ethernet PHY RTL8201FL-VB-CG (Realtek) SDRAM IS42S16320F-7TL (ISSI) NAND flash memory Not used S34ML01G100TFI000 (Cypress)
RZ/A2M SUB Board RTK79210XXB00000BE 1. Overview Absolute Maximum Ratings Table 1.4 lists absolute maximum ratings for RTK79210XXB00000BE. Table 1.4 RTK79210XXB00000BE Absolute Maximum Ratings Symbol Item Rating value Note 5V power voltage -0.3V to 6.25V Vss is the reference. D3.3V 3.3V power voltage -0.3V to 4.2V Vss is the reference.
• Memory SDRAM: 64 Mbytes x 1 - ISSI S42S16320F-7TL • EEPROM: 16 KBytes x 1 - Renesas R1EX24128ASAS0A • NAND flash memory: 128 MBytes x 1 is possible to mount on the board pattern. - Cypress S34ML01G100TFI000 USB interface Connection for the RZ/A2M USB2.0 host/function module and USB connector...
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.2.1 Overview of RZ/A2M RTK79210XXB00000BE is used by connecting to an RZ/A2M CPU board RTK7921053C00000BE equipped with RZ/A2M. RZ/A2M is a 32 bit RISC microprocessor which operates at a maximum clock speed of 528 MHz. 2.2.2 List of RZ/A2M Pin Functions Used on RTK79210XXB00000BE Table 2.2.1 to Table 2.2.16 lists RZ/A2M Pin Functions used on RTK79210XXB00000BE...
Page 21
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.2 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (2) Pin Name Pin Function Description Comments PE_4 / ET0_CRS/RMII0_CRSDV Connects to Ethernet PHY1 (U27) SW6-4:ON ET0_CRS/RMII0_CRSDV / VIO_D4 Connects to CMOS camera connector SW6-4:OFF VIO_D4 / SSIFS0 / (CN17)
Page 22
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.3 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (3) Pin Name Pin Function Description Comments PD_0:High PL_1 / MD_CLK / IRQ5 MD_CLK Connects to DIP switch (SW1 on the SW1-2 CPU board) PD_0:Low...
Page 23
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.4 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (4) Pin Name Pin Function Description Comments P6_1 / ET0_TXEN/RMII0_TXDEN Connects to Ethernet PHY1 (U27) SW6-4:ON ET0_TXEN/RMII0_TXDEN VIO_CLK Connects to CMOS camera connector SW6-4:OFF / VIO_CLK / SCK3 / (CN17)
Page 24
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.5 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (5) Pin Name Pin Function Description Comments ― PD_3 / RIIC1SDA / IRQ3 / PD_3 Connects to MIPI CSI-2 connector MTCLKD / GTETRGD (CN2 and J1 on the CPU board) PVcc ―...
Page 25
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.6 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (6) Pin Name Pin Function Description Comments PD_6 / RIIC3SCL / IRQ6 RIIC3SCL Connects to CMOS camera connector (CN17) Connects to EEPROM (U32) Connects to digital image input/output connector (CN15) ―...
Page 26
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.7 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (7) Pin Name Pin Function Description Comments ― JP_2 / TMS Connects to UDI connector (CN5 on the CPU board) PB_1 / A25 / DV0_DATA4 / DV0_DATA4 Connects to digital image input/output LCD0_DATA19 / SSIFS1 /...
Page 27
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.8 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (8) Pin Name Pin Function Description Comments ― HM_DQ6/OM_SIO6 HM_DQ6 Connects to HyperMCP (U3 on the CPU board) ― HM_DQ7/OM_SIO7 HM_DQ7 Connects to HyperMCP (U3 on the CPU board) ―...
Page 28
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.9 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (9) Pin Name Pin Function Description Comments PG_1 / ET0_TXD2 / VIO_D9 Connects to CMOS camera connector VIO_D9 / MOSI0 / (CN17) MTIOC3C / HM_INT# P7_5 / CKE / DRP08 /...
Page 29
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.10 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (10) Pin Name Pin Function Description Comments P0_3 / D3 / DRP27 / Connects to SDRAM (U3) SW6-1:ON DV0_DATA20 / MTIOC7A / DRP27 Connects to DRP connector (CN2) SW6-1:OFF...
Page 30
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.11 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (11) Pin Name Pin Function Description Comments PH_5 / HM_RSTO# / NAF2 / ET1_EXOUT Connects to Ethernet PHY2 (U28) SW6-5:ON ET1_EXOUT / MTIC5U / NAF2 Connects to NAND flash memory Not used...
Page 31
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.12 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (12) Pin Name Pin Function Description Comments ― SD0_DAT3 Connects to microSD card slot (CN1 on the CPU board) connection PK_4 / ET1_RXD0/RMII1_RXD0 Connects to Ethernet PHY2 (U28) SW6-5:ON...
Page 32
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.13 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (13) Pin Name Pin Function Description Comments P2_0 / D12 / GTIOC6A / Connects to SDRAM (U3) SW6-1:ON IRQ5 / CAN1RX / OTG_EXICEN0 PC_2 / OTG_EXICEN0 / PC_2...
Page 33
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.14 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (14) Pin Name Pin Function Description Comments USBVss USBVss USBDPVcc1 ― PC_7 / OVRCUR0 / FRB / OVRCUR0 Connects to USB VBUS power supply ET1_RXD3 / SD1_WP / control IC (U5 on the CPU board) LCD0_TCON0 / IRQ6...
Page 34
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.15 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (15) Pin Name Pin Function Description Comments PC_5 / VBUSEN1 / FRE / VBUSEN1 Connects to USB Mini-B port (CN13) AA17 ET1_RXDV / SPDIF_OUT / LCD0_TCON2 / IRQ0 ―...
Page 35
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.2.16 List of RZ/A2M Pin Function Selections Used on the RTK79210XXB00000BE (16) Pin Name Pin Function Description Comments AB17 PC_3 / OTG_ID0 / FCLE / LCD0_TCON4 Connects to digital image input/output ET1_COL / SSL20 / connector (CN15) LCD0_TCON4 ―...
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.2.3 RTK79210XXB00000BE Interface Use Combination List Table 2.2.17 shows the usage permission/denial list for each RTK79210XXB00000BE interface. The ○ marks indicate that combined use by both interfaces is possible, while the × marks indicate that combined use is not possible. Table 2.2.17 RTK79210XXB00000BE Interface Usage Permission List RTK7921053C00000BE...
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Memory 2.3.1 SDRAM The RTK79210XXB00000BE is equipped with external SDRAM×1 shown in Table 2.3.1 as the standard configuration. SDRAM control is performed by the RZ/A2M on-chip bus state controller (BSC). There is a 16-bit connection to the SDRAM.
Page 39
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.3.4 Bus State Controller Settings (SDRAM read/write) (1) User region Target device Bus state controller settings ■ CS3 space bus control register (CS3BCR) IS42S16320F-7TL ・Initial setting: H'36DB 0C00 ・Recommended setting: H'0000 4C00 - Memory specification: TYPE[2:0] = B'100;...
Page 40
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.3.5 Bus State Controller Settings (SDRAM read/write) (2) User region Target device Bus state controller settings ■ AC characteristics adjustment register (ACADJ) IS42S16320F-7TL ・Initial setting: H'0000 0000 ・Recommended setting: H'0000 000A - Output characteristics adjustment bit: SDRODLY = B’0000;...
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.3.2 NAND Flash Memory Interface RTK79210XXB00000BE is possible to mount NAND flash memory x 1 shown in Table 2.3.6 on the board pattern. NAND flash memory control is performed by the RZ/A2M on-chip NAND flash controller FLCTL).
Page 42
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.3.7 Function Setting Table of DIP Switches SW6-5 and SW6-6 for System Setting Function Switch SW6-5 P3_[5 :1] and PH_5, PK_[4 :0] are used as Ethernet P3_[5 :1] and PH_5, PK_[4 :0] are used as FLCTL PHY2 control pins (default setting).
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.3.3 EEPROM Interface RTK79210XXB00000BE is equipped with EEPROM x 1 shown in Table 2.3.8 as the standard configuration. EEPROM control is performed by the RZ/A2M on-chip 12C bus interface (RIIC) on channel 3. Figure 2.3.3 shows EEPROM interface block diagram.
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications USB Interface RTK79210XXB00000BE is equipped with a USB series A port x 1 and USB Mini-B port x 1 as the standard configuration of USB connectors. However, USB interface pins are shared by the Series A port pins and Mini-B port pins, therefore Series A port and Mini-B port cannot be used at the same time.
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Serial Interface On the RTK79210XXB00000BE, channel 4 of serial communications interface built into the RZ/A2M on-chip FIFO (SCIFA) is connected to the serial port connector (USB Micro-B) (CN5) via the USB serial converter IC (RL78/G1C). When equipping and connecting E1 connector (J1), be sure of the direction of the number 1 pin.
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Interrupt Switches RTK79210XXB00000BE is equipped with an RZ/A2M NMI and IRQ0 interrupt signal input push switches (NMI switch and IRQ0 switch). The interrupt signal from IRQ0 RZ/A2M can be used to cancel the RZ/A2M deep standby mode. However, because the IRQ0pin is shared with the Ethernet PHY1 and Ethernet PHY2, when using the IRQ0 switch, the user must connect JP2 with the 2-pin of JP1.
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Clock Configuration RZ/A2M receives the following three types of clock inputs from the RZ/A2M CPU board. ・RZ/A2M input clock :24 MHz ・RZ/A2M USB clock :48 MHz ・RZ/A2M RTC clock :32.768 kHz RZ/A2M receives the following two clock inputs from RTK79210XXB00000BE. ・RZ/A2M audio clock :11.2896MHz ・RZ/A2M VDC6 clock...
Page 48
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Table 2.7.1 Function Setting Table of DIP Switches SW6-4 and SW6-6 for System Setting Function Switch SW6-4 P6_1 is used as RMII_TXDEN pin. P6_1 is used as VIO_CLK input pin. (default setting) SW6-6 PJ_6 is used as LCD0_CLK output pin.
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Reset Control On RTK79210XXB00000BE, a reset signal from the reset IC on the RZ/A2M CPU board is input to the Ethernet PHY1 (U27), Ethernet PHY2 (U28), and digital image input/output connector (CN15). There are two types of system reset: power-on reset and switch-based reset. Figure 2.8.1 shows a reset control block diagram.
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications Power Voltage Configuration RTK79210XXB00000BE uses 5V power supply, and the regulator on the RZ/A2M CPU board generates 3.3V power supply. 5V power supply can also be supplied from the RZ/A2M CPU board. USB serial converter IC (U23) is operated by the VBUS power supply provided from USB Micro-B connector (CN5). Figure 2.9.1 shows a power configuration diagram.
RTK79210XXB00000BE is equipped with a Cirrus audio CODEC WM8978 × 1 for audio interface. The WM8978 register control is performed on the channel 0 of the RZ/A2M on-chip Renesas serial peripheral interface (RSPI), and the input/output control for audio data is performed on the channel 0 of the RZ/A2M on-chip serial sound interface (SSIF-2).
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.11 CMOS Camera Interface RZ/A2M is equipped with an on-chip capture engine unit (CEU) that captures digital image data externally input, and transfers the data to memory. On RTK79210XXB00000BE, CEU pins of RZ/A2M connect with 26 pin MIL pitch connector to enable connection with various CMOS cameras.
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.12 SD Card Interface RTK79210XXB00000BE is equipped with 4-bit SD card slot, and it connects to the channel 1 of the RZ/A2M on-chip SD/MMC host interface (SDHI). Figure 2.12.1 shows the SD card interface block diagram. 3.3V RZ/A2M (U1) SD card slot(CN10)...
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.13 LAN Interface RTK79210XXB00000BE is equipped with Realtek Ethernet PHY RTL8201FL-VB-CG × 2, which can communicate with the channel 0 and channel 1 of the RZ/A2M on-chip ethernet controller (ETHERC). The Ethernet PHY incorporates the Wake-On-Lan (WOL) functionality, and outputs a WOL signal when a Magic Packet has been detected, allowing the deep standby mode of RZ/A2M to be canceled.
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.14 Key Input Switches Port P5_6 is set as an analog input pin (AN006), and can be used as a key input switch through an A/D converter (ADC) Figure 2.14.1 shows the key input switch block diagram, and Table 2.14.1 shows the AD input pin voltage and AD value when each switch is pressed.
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.15 VDC6 Interface RZ/A2M has a digital image signal input pin (DV pin) which supports YCbCr422, YCbCr444, RGB888, RGB666, and RGB565 images. In addition, there is a digital image signal output pin (LCD pin) which supports a maximum image size of 1999 pixels (horizontal) by 2035 lines (vertical).
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.16 LVDS Interface RTK79210XXB00000BE is equipped with a 1.25mm pitch 20 pin connector, which allows connection with the RZ/A2M LVDS interface. There is also a connector for the LVDS backlight. Figure 2.16.1 shows the LVDS interface block diagram. RZ/A2M (U1) LVDS connector(CN14)...
RZ/A2M SUB Board RTK79210XXB00000BE 2. Function specifications 2.17 DRP Interface RTK79210XXB00000BE is equipped with a 40 pin MIL connector, which allows interface with the RZ/A2M DRP interface. Figure 2.17.1 shows the DRP interface block diagram, and Table 2.17.1 shows the function setting table of DIP switches SW6-1, SW6-2, and SW6-3 for system setting.
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications Operating specifications Overview of Connector Figure 3.1.1 and Figure 3.1.2 show connector layout diagrams for RTK79210XXB00000BE. CN15: Digital image signal CN1: CPU board CN16: LVDS back line Input/output connector Connector connector CN14: LVDS CN18: DC power connector source jack...
Page 62
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications CN10: SD card slot CN12: USB Series A Port Figure 3.1.2 RTK79210XXB00000BE Connector Layout Diagram (S Side Top View) R20UT4398EJ0100 Rev.1.00 2018.10.11...
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.1.1 CPU Board Connector (CN1) The RTK79210XXB00000BE can be connected to the RZ/A2M CPU board RTK7921053C00000BE via the CPU board connector (CN1). Figure 3.1.3 shows the CPU board connection pin layout diagram, and Table 3.1.1 to Table 3.1.3 show CPU board connector pin layout table.
Page 64
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications Table 3.1.1 CPU Board Connector (CN1) Pin Layout Table (1) Signal name Signal name RES# PC_5 / VBUSEN1 D3.3V PC_3 / LCD0_TCON4 D3.3V AVcc D3.3V P5_6 / AN006 P5_3 AVss P5_5 / SD1_WP P5_4 / SD1_CD P5_7 / IRQ3 PC_4 / LCD0_TCON3...
Page 65
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications Table 3.1.2 CPU Board Connector (CN1) Pin Layout Table (2) Signal name Signal name PE_1 / ET0_RXD0/RMII0_RXD0 / VIO_D7 PA_2 / DV0_DATA11 / LCD0_DATA12 PA_7 / DV0_DATA6 / LCD0_DATA17 PA_0 / DV0_DATA13 / LCD0_DATA10 PE_2 / ET0_RXD1/RMII0_RXD1 / VIO_D6 PE_3 / ET0_RXER/RMII0_RXER / VIO_D5 PA_1 / DV0_DATA12 / LCD0_DATA11...
Page 66
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications Table 3.1.3 CPU Board Connector (CN1) Pin Layout Table (3) Signal name Signal name PJ_1 / IRQ0 P1_0 / D7 / DRP31 PH_5 / NAF2 / ET1_EXOUT PH_6 / ET1_WOL PK_4 / ET1_RXD0/RMII1_RXD0 / NAF7 P3_1 / ET1_RXER/RMII1_RXER / FALE PK_5 / NAF1 PG_4 / VIO_D15...
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.1.3 Mic-in Pin Jack (CN3) RTK79210XXB00000BE is equipped with the mic-in pin jack (CN3). Figure 3.1.5 shows the mic pin jack layout diagram, and Table 3.1.5 shows the mic-in pin jack layout table. C side top view Figure 3.1.5 Mic-in Pin Jack (CN3) Layout Diagram...
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.1.4 Line out Pin Jack (CN4) RTK79210XXB00000BE is equipped with the line out pin jack (CN4). Figure 3.1.6 shows the line out pin jack layout diagram, and Table 3.1.6 shows the line out pin jack layout table. C side top view Figure 3.1.6 Line Out Pin Jack (CN4) Layout Diagram...
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.1.5 Serial Board Connector (CN5) RTK79210XXB00000BE is equipped with a serial board (USB Micro-B) connector (CN5). Figure 3.1.7 shows the serial board connector pin layout diagram, and Table 3.1.7 shows the serial board connector pin layout table.
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.1.6 LAN Connector (CN8, CN9) RTK79210XXB00000BE is equipped with the LAN connectors (CN8, CN9). Figure 3.1.8 shows the LAN connector pin layout diagram, and Table 3.1.8 shows the LAN connector pin layout table. C side top view Side view Figure 3.1.8...
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.1.8 USB Connector (CN12, CN13) RTK79210XXB00000BE is equipped with the series A port (CN12) and Mini-B port (CN13). Figure 3.1.10 shows the series A port pin layout diagram, and Figure 3.1.11 shows the Mini-B port pin layout diagram. Table 3.1.10 shows the series A port pin layout table, and Table 3.1.11 shows the Mini-B port pin layout table.
Page 75
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications C side top view CN13 Side view Figure 3.1.11 Mini-B Port (CN13) Pin Layout Diagram Table 3.1.11 Mini-B Port (CN13) Pin Layout Table Signal name VBus (PC_0 / VBUSIN1) D- (DM1) D+ (DP1) IC (connects to test pin TP3) GND (Vss) Red characters...
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.1.9 LVDS Connector (CN14, CN16) RTK79210XXB00000BE is equipped with the LVDS connector (CN14) and the back light connector (CN16) for power supply. Figure 3.1.12 shows the LVDS connector and LVDS backlight connector pin layout diagram, Table 3.1.12 shows the LVDS connector pin layout table, and Table 3.1.13 shows the LVDS back light connector pin layout table.
Page 77
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications Table 3.1.13 LVDS Back Light Connector (CN16) Pin Layout Table Signal name VLED (5V) (+5V) VLED (5V) (+5V) DIMMER (Brightness Adjust) (connects to +3.3V via 10kΩ resistor) ENABLE (connects to +3.3V via 10kΩ resistor) GND (Vss) GND (Vss) R20UT4398EJ0100 Rev.1.00...
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.1.10 Digital Image Input/output Connector (CN15) RTK79210XXB00000BE is equipped with the digital image input/output connector (CN15). Figure 3.1.13 shows the digital image input/output connector pin layout diagram, and Table 3.1.14 shows the digital image input/output connector pin layout.
Page 79
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications Table 3.1.14 Digital Image Input/output Connector (CN15) Pin Layout Table Signal name Signal name DATA0 (PF_7 / DV0_DATA23 / LCD0_DATA0) DATA1 (PH_2 / DV0_DATA22 / LCD0_DATA1) DATA2 (PF_6 / DV0_DATA21 / LCD0_DATA2) DATA3 (PF_5 / DV0_DATA20 / LCD0_DATA3) DATA4 (PF_4 /...
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.1.11 CMOS Camera Connector (CN17) RTK79210XXB00000BE is equipped with a CMOS camera connector (CN17). Figure 3.1.14 shows the CMOS camera connector pin layout diagram, and Table 3.1.15 shows the CMOS camera connector pin layout. CMOS camera connector (CN17) does not have a reverse insertion prevention guide, so be sure to insert in the direction of the #1 pin during connection.
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.1.12 DC Power Supply Jack (CN18) RTK79210XXB00000BE is equipped with the DC power supply jack (CN18) for providing power to the system. Figure 3.1.15 shows the power supply connector pin layout diagram, and Table 3.1.16 shows the power supply connector pin layout table.
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.2.1 Jumpers (JP1 and JP2) RTK79210XXB00000BE is equipped with two system setting jumpers. Figure 3.2.2 shows the jumper layout diagram, and Table 3.2.1 shows the jumper setting table. C side top view Figure 3.2.2 RTK79210XXB00000BE Jumper Layout Diagram Table 3.2.1 Jumper Setting Table (JP1 and JP2)
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications 3.2.2 Switch Functions RTK79210XXB00000BE is equipped with six switches. Figure 3.2.3 shows the mounted switch layout diagram, Table 3.2.2 lists the mounted switches, and Table 3.2.3 provides the explanation of DIP switch functions. C side top view SW5 SW4 SW3 SW2 9 10...
Page 85
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications Table 3.2.2 Mounted RTK79210XXB00000BE Switch Overview Numbers Function Note Power supply switch NMI switch Refer to section 2.6 for details. IRQ0 switch Key input switch Refer to section 2.14 for details. Key input switch Refer to Table 3.2.3 DIP switch for system settings...
RZ/A2M SUB Board RTK79210XXB00000BE 3. Operating specifications External Dimensions Figure 3.3.1 shows the external dimensions of the RTK79210XXB00000BE C side top view. <C side top view> unit: mm Figure 3.3.1 RTK79210XXB00000BE External Dimensions Diagram R20UT4398EJ0100 Rev.1.00 3-26 2018.10.11...
Page 103
Revision History RZ/A2M SUB Board RTK79210XXB00000BE User's Manual Rev. Date of Revised content issue Page Point ― 1.00 2018.10.11 Issue of first version...
Page 104
RZ/A2M SUB Board RTK79210XXB00000BE User's Manual Date of issue 11 Oct 2018 Rev.1.00 Issue Renesas Electronics Corporation 3-2-24 Toyosu (Toyosu Foresia), Kotoku, Tokyo 〒135-0061...
Page 105
SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 1001 Murphy Ranch Road, Milpitas, CA 95035, U.S.A. Tel: +1-408-432-8888, Fax: +1-408-434-5351 Renesas Electronics Canada Limited 9251 Yonge Street, Suite 8309 Richmond Hill, Ontario Canada L4C 9T3...
Page 106
RZ/A2M SUB Board RTK79210XXB00000BE User's Manual R20UT4398EJ0100...
Need help?
Do you have a question about the RTK79210**B00000BE and is the answer not in the manual?
Questions and answers