Operating Instructions; Master-Slave Set Up - ADJ MINI DEKKER LZR User Instructions

• HOLD - If the DMX signal is lost the fixture will stay in the last DMX setting. If power is applied and this mode
is set, the unit will automatically go into the last DMX set up.
• PRGN (Master Slave) - If the DMX signal is lost or power is applied, the unit will automatically go into Master
Slave mode and run a built-in show.
• BLAC (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode.
3. Press ENTER to confirm your desired set up.
LED
- With this function you can have the LED display turn off after 10 seconds.
1. Press the MENU button until "LED" is displayed, press ENTER.
2. The display will show either "ON" or "OFF". Press the UP or DOWN buttons to select "ON" to keep the LED
display on at all times, or "OFF" to switch to have the LED display switch off after 10 seconds.
STRO
- This will activate strobing.
1. Press the MENU button until "STRO" is displayed, press ENTER.
2. Use the UP or DOWN buttons to activate strobing or deactivate it.
TEST
- This function will run a self test program.
1. Press the MENU button until "TEST" is displayed, press ENTER.
2. The fixture will now run a self test.
DISP
- This function will reverse the display 180º.
1. Press the MENU button until "DISP" is displayed, press ENTER.
2. Press ENTER to "flip" the display. Press ENTER to "flip" it again. Press ENTER when you have made your
desired setup.
3. Press ENTER to confirm. To make you LED display reappear again press any button.
FHRS
- With this function you can display the running time of the unit.
1. Press the MENU button until "FHRS" is displayed, press ENTER.
2. The running time of the fixture will now be displayed. Press MENU to exit.
VER
- Use this function to display the Software version of the unit.
1. Press the either the MENU button until "VER" is displayed, press ENTER.
2. The display will show the software version.
RSET
- This function will reset the unit.
1. Press the MENU button until "RSET" is displayed. Press the ENTER button and the unit will reset itself.

OPERATING INSTRUCTIONS

Universal DMX Control: This function allows you to use a universal DMX-512 controller to control the patterns,
rotation and strobing. A DMX controller allows you to create unique programs tailored to your individual needs.
1. The Mini Dekker LZR has two DMX channel modes; a 2 channel mode and a 7 channel mode. See pages
12-13 for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures on pages 6-7 as well as the set-up
specifications that are included with your DMX controller.
3. Follow the instructions on page 10 to set the DMX address.
4. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
5. For help operating in DMX mode consult the manual included with your DMX controller.
Sound Active Mode: This mode allows a single unit or several units linked together, to run to the beat of the
music.
1. Press the MENU button until "Soun" is displayed, and press ENTER.
2. Press the UP or DOWN buttons to either activate sound active mode or deactivate, and press ENTER. The
unit will now run to the beat of the music.
3. The sound sensitivity can be adjusted by turning the sound sensitivity knob located on the back of the unit.
Turning the knob clockwise is most sensitive and turn it counter-clockwise is least sensitive.
Show Mode: This mode allows a single unit or several units linked together, to run to a built-in program.
1. Press the MENU button until "Show" is displayed, and press ENTER to activate.

MASTER-SLAVE SET UP

A.D.J. Supply Europe B.V. – www.americandj.eu – Mini Dekker LZR Instruction Manual Page 11