ADJ MINI DEKKER LZR User Instructions page 10

System Menu: When making adjustments press ENTER to confirm your setup then press and hold the
MENU button for at least 3 seconds. To exit without making any adjustments press the MENU button.
The display will lock after 30 seconds, press the MENU button for 3 seconds to unlock.
ADDR
- DMX Address Setting.
1. Press the either the MENU, UP, or DOWN buttons until "ADDR" is displayed, press ENTER.
2. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired
address. Press ENTER to set your desired DMX address.
CHND
- This will let select your desired DMX channel mode.
1. Press the MENU button until "CHND" is displayed, press ENTER. The current DMX channel mode will be
displayed
2. Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confim and
exit.
SHND
- Show modes 0-2 (Factory programs).
1. Press the MENU button until "SHND" is displayed, press ENTER.
2. "Sh X" will now be displayed, "X" representing a number between 0-6. Shows 1-2 are factory programs, while
show "0" is random mode. Use the UP or DOWN buttons to find your desired show.
3. When you have found your desired show press ENTER, then press and hold the MENU button for at least 3
seconds to activate. After you have set your desired show, it can be changed at any time using the UP or DOWN
buttons.
SPEE
- Show mode speed.
1. Press the MENU button until "SPEE" is displayed, press ENTER.
2. A number between 0-100 will now be displayed, the number is the current speed setting. Use the UP or
DOWN buttons to adjust the show speed. "0" being the slowest speed and "100" being the fastest.
3. Press ENTER to set the speed then press and hold the MENU button for at least 3 seconds to show mode.
SLND
- This will let you set unit as a master or slave in a master/slave configuration.
1. Press the MENU button until "SLND" is displayed, press ENTER. Either "MAST", "SL 1", or "SL 2" will be
displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim.
Note: In a Master/Slave configuration you can set one fixture to Master and then set the next fixture to "SL 2",
the fixtures will now have contrast movement to each other.
SOUN
- Sound Active mode.
1. Press the MENU button until "SOUN" is displayed, press ENTER.
2. The display will show either "ON" or "OFF". Press the UP or DOWN buttons to select "ON" to activate sound
active mode, or "OFF" to deactivate sound active mode.
3. Press ENTER to confirm.
SOSE
- In this mode you can adjust the sound sensitivity.
1. Press the MENU button until "SOSE" is displayed, press ENTER.
2. A number between 0-100 will be displayed. Press the UP or DOWN buttons to adjust the sound sensitivity. 0
being the least sensitive, and 100 being the most sensitive.
3. When you have found your desired setting press ENTER to confirm.
NODN
- This mode can be used as a precaution mode, that in case the DMX signal is lost, interrupted,
or power is lost, the operating mode chosen in this setup is the running mode the fixture will revert to.
You can also set this as the operating mode you would like the unit to return to when power is applied.
1. Press the MENU button until "NODN" is displayed, and either "MASL", "BLND", or "LAST" will be displayed
beneath.
2. Press ENTER and the bottom choice will begin to flash. Use the UP or DOWN buttons to choose an operating
mode you would like the unit to start up in when power is applied or the DMX signal is lost.
SYSTEM MENU (continued)
A.D.J. Supply Europe B.V. – www.americandj.eu – Mini Dekker LZR Instruction Manual Page 10