ORiNG TGAR-1062-M12-3G Quick Installation Manual

EN50155
Wireless
Q I
uick nstallation
Access Point ROUTER

Introduction

With two LAN ports in M12 connectors and EN50155 compliance, the
1062/2062/1662-M12-3G/4G industrial access point routers are ideal for
rolling stock applications. The IEEE802.11 a/b/g/n routers provide a fast and
effective way to communicate with the Internet over wired or wireless LANs.
Three operation modes are available, including dynamic/static IP route,
PPPoE authentication, and cellular modem dial up. You can set up a WLAN
environment based on your requirements by dialing up cellular modem.
With dual Ethernet ports in switch mode, you can use Daisy Chain to
reduce the usage of Ethernet switch ports.

Package Contents

The devices are shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Contents Pictures
Router
2.4GHz/5GHz Wi-Fi
Antenna
1 (TGAR-1062/1662-M12-3G)
Cellular 3G Antenna
or 2 (TGAR-2062-M12-3G)
1 (TGAR-1062/1662-M12-4G)
Cellular LTE Antenna
or 2 (TGAR-2062-M12-4G)
CD
QIG
Allen Key

Preparation

Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
TGAR Series
G
uide
Dimension
TGAR-
Number
1
Panel Layouts
2 (TGAR-1062/2062) or
4 (TGAR-1662)
12 13
11
TGAR-1062-M12
PWR1 WAN
1
PWR2
4
1
ETH1 WLAN
2
ETH2 5
3 Fault
9
DO1 DO2 DO DI DI1
GND
1
DO4 DO3 DI4
10
Power V1+
V1-
1
TGAR-1062-M12
1. PWR status LED
2. LAN port status LED
3. Fault status LED
4. WAN status LED
5. WLAN status LED
6. Relay output port
7. Console port
Side Panel
1. Wi-Fi Antenna connector
2. Reset button
1907-2-29-TGAR-1.0
TGAR Series
125.6
15.0
Relay N.C.
1A@24VDC
TGAR Series
PWR1 WAN Relay Output
PWR2
ETH1 WLAN1
ETH2 WLAN2 RxD TxD
N.C.
Fault
RSVD GND Console
RS-232, 115200bps, 8, N, 1
DO1 DO2 DI1 DI2
DO DI ETH2 ETH1
GND COM
DO4 DO3 DI4 DI3 1 2
7 3
6 4
5 8
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
Power V1+ V2+ 8 BI_DB-
V1- V2-
R2.5
12.5
R4.0
56.5 19.1 65
86.0
Front Panel
12 13 12
Relay N.C. 11 Relay N.C. 11
1A@24VDC 1A@24VDC
6 6
TGAR-2062-M12 TGAR-1662-M12
Relay Output PWR1 WAN1 Relay Output PWR1
1 4 1
PWR2 WAN2 PWR2
ETH1 WLAN ETH1
2 2
7 7
RxD TxD ETH2 5 RxD TxD ETH2
N.C. N.C.
3 Fault 3 Fault
Console Console
RSVD GND RSVD GND
RS-232, 115200bps, 8, N, 1 RS-232, 115200bps, 8, N, 1
8 9 8 9
DI2 ETH2 ETH1 DO1 DO2 DO DI DI1 DI2 ETH2 ETH1 DO1 DO2 DO
COM GND COM GND
DI3 1 2 DO4 DO3 DI4 DI3 1 2 DO4 DO3
7 3 7 3
6 4 6 4
5 8 10 5 8 10
1 BI_DC+ 1 BI_DC+
2 BI_DD+ 2 BI_DD+
3 BI_DD- 3 BI_DD-
4 BI_DA- 4 BI_DA-
5 BI_DB+ 5 BI_DB+
6 BI_DA+ 6 BI_DA+
7 BI_DC- 7 BI_DC-
V2+ Power V1+ V2+ Power
8 BI_DB- 8 BI_DB-
V2- V1- V2-
TGAR-2062-M12 TGAR-1662-M12
8. Ethernet LAN ports
9. DI/DO ports
10. Power connector
11. 2.4/5GHz Wi-Fi antenna
12. Cellular antenna connector
13. SIM card slot
Top Panel Bottom Panel
1
2
TGAR-2062-M12
PRINTED ON RECYCLED PAPER
EN50155 Industrial Wireless LAN
Access Point Router

Installation

Wall-mount

The device can be fixed to the wall. Follow the steps below
to install the device on the wall.
Step 1: Hold the d evice upright against the wall
Step 2: Insert four screws through the large opening of
the keyhole-shaped apertures at the top and bottom of
the unit and fasten the screw to the wall with a screwdriver.
Step 3: Slide the d evice downwards and tighten the four
screws for added stability.

Wiring

For pin assignments of power, console and relay output ports, please refer to the following tables.
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.

Power port pinouts

The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
13

Relay output port pinouts

Relay N.C.
1A@24VDC Relay N.C.
6
WAN 4 Relay Output
3A@24VDC
WLAN1
7
WLAN2 RxD TxD
N.C.
5
Console
RSVD GND
RS-232, 115200bps, 8, N, 1
8
DI DI1 DI2 ETH2 ETH1

Network Connection

COM
DI4 DI3 1 2
7 3
6 4
5 8
1 BI_DC+
2 BI_DD+ The AP router has two 10/100/1000 Base-T(X) Ethernet ports. According to the link type, the AP
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
V1+ V2+
8 BI_DB- router uses CAT 3, 4, 5, 5e, UTP cables to connect to any other network device (PCs, servers,
V1- V2-
d evicees, routers, or hubs). Please refer to the following table for cable specifications.
Cable Type
10Base-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft)
100Base-T(X) Cat. 5 100-ohm UTP UTP 100 m (328 ft)
1000Base-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328 ft)
M12/8P Pin Definition
PIN
1 2
1
7 3
6 4 2
5 8
3
4
5
6
7
8
Version 1.0
V1+ V2+
V1- V2-

DI/DO Port Pinouts

DI DO
DI1 DI2 DO1 DO2
COM GND
DI4 DI3 DO4 DO3
Max. Length Connector
M12
M12
M12
Console Port Pin Definition
Definition
RxD TxD
N.C.
BI_DC+
RSVD GND
BI_DD+
RS-232, 115200bps, 8, N, 1
BI_DD-
BI_DA-
BI_DB+
BI_DA+
BI_DC-
BI_DB-
Quick Installation Guide