ORiNG TGS-9200-M12-BP2 Quick Installation Manual

EN50155
Switch
Q I
I N D U S T R I A L
uick nstallation
Introduction
T M
ORing's Transporter series managed Ethernet switches are designed for
industrial applications, such as rolling stock, vehicle, and railway
applications. TGS-9200-M12-BP2 is managed Redundant Ring Ethernet
switch with 20x10/100/1000Base-T(X) ports which is specifically designed for
the toughest and fully compliant with EN50155 requirement.
support Ethernet Redundancy protocol, O-Ring (recovery time < 30ms over
250 units of connection), O-Chain, MRP
802.1s/w/D) can protect your mission-critical applications from network
interruptions or temporary malfunctions with its fast recovery technology.
TGS-9200-M12-BP2 includes 2 sets of bypass ports that protect the network
from failures and Network maintenance by ensuring network integrity during
power loss. And support wide operating temperature from -40 C to 75 C.
TGS-9200-M12-BP2 can also be managed centralized and convenient by
Open-Vision, Except the Web-based interface, Telnet and console (CLI)
configuration. Therefore, the switch is one of the most reliable choices for
EN50155 highly-managed Ethernet application.
*NOTE : This function is available by request only
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Contents Pictures
TGS-9200-M12-BP2
CD
QIG
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
TGS-9200-M12-BP2
TGS-9200-M12-BP2
G
uide
Dimension
The switch
*NOTE MSTP/RSTP/STP (IEEE
o o
Panel Layouts
Front View
Number
TGS-9200-M12-BP2
1
Reset
PWR1 PWR2 R.M. Ring Fault
2 3 4 5 6
1
Relay
N.C. Power Power
Failure Failure
11 3A@24VDC Bypass Bypass
Relay Output
RXD TXD
N.C.
12 RSVD GND
RS-232, 115200bps, 8, N, 1
Console
1
Power
Failure
Bypass
7
V1+ V2+
V1- V2- Power
1
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screws to the wall with a screwdriver.
Step 3: Slide the
1907-200-Q9200M1222-FX010
Unit =mm (Tolerance ±0.5mm)
260
193.9
Ø5.0
15
1 BI_DC+
2 BI_DD+ 1 2
4 BI_DA- 3 BI_DD-
5 BI_DB+ 7 3 Ø8.0
6 BI_DA+ 6 4
7 BI_DC- 5
8 BI_DB- 8
G1~G20
TGS-9200-M12-BP2
Reset LNK/ACT LNK/ACT
PWR1 PWR2 R.M. Ring Fault
Speed Speed
Relay G4 G8 P12 G16 G20
N.C. Power Power
Failure Failure
3A@24VDC Bypass Bypass
Relay Output LNK/ACT LNK/ACT
RXD TXD Speed Speed
G3 G7 G11 G15 G19
N.C.
RSVD GND
RS-232, 115200bps, 8, N, 1 Console LNK/ACT LNK/ACT
Speed Speed
Power G2 G6 G10 G14 G18
Failure
Bypass
LNK/ACT LNK/ACT
V1+ V2+
Speed Speed
Power G1 G5 G9 G13 G17
V1- V2-
91.3 19.4
1. Reset button
2. Power1 status LED
3. Power2 status LED
1 BI_DC+
2 BI_DD+ 1 2
3 BI_DD- 4. R.M. status LED
4 BI_DA- 7 3
5 BI_DB+
6 BI_DA+ 6 4
7 BI_DC-
5 8 5. Ring status LED
8 BI_DB-
G1~G20
6. Fault LED
LNK/ACT LNK/ACT
7. Power connector
Speed Speed
G16 G20
G4 G8 P12
8. Gigabit Ethernet ports
LNK/ACT LNK/ACT
(G1 - G4 are bypass ports)
Speed Speed
G3 G7 G11 G15 G19 9. Link/ACT LED for Gigabit ports
10. Speed LED for Gigabit ports
LNK/ACT LNK/ACT
11. Relay output
Speed Speed
G2 G6 G10 G14 G18
9
12. Console port
LNK/ACT LNK/ACT
Speed Speed
G1 G5 G9 G13 G17
8 10
d evice upright against the wall
d evice downwards and tighten the four screws for added stability.
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
PRINTED ON RECYCLED PAPER
EN50155 20-port managed
Gigabit Ethernet switch
Wiring
For pin assignments of power, console and relay output ports, please refer to the following tables.
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for dual power inputs.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Console port pinouts
RXD TXD
N.C.
N.C. GND
RS-232, 115200bps, 8, N, 1
Relay output port pinouts
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a cable with an M12
A-coded 5-pin male connector to connect the relay. The
relay contacts will detect user-configured events and form
an close circuit when an event is triggered.
Network Connection
The switch has twenty 10/100/1000Base-T(X) Ethernet ports in the form of M12 connector.
Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network
devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
Cable Type Max. Length Connector
8-pin female M12
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft)
A-coding connector
8-pin female M12
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft)
A-coding connector
8-pin female M12
1000BASE-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328 ft)
A-coding connector
For pin assignments of the Ethernet ports, please refer to the following tables.
8-Pin Gigabit Port Definition
1 2
7 3
PIN Definition
6 4
5 8
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
Quick Installation Guide
Version 2.0
V1+ V2+
V1- V2-
Relay
N.C.
3A@24VDC