EN50155
Switch
Q
I
I N D U S T R I A L
uick
nstallation
Introduction
The
TPS-3082GF-MM-M12-QODC
is a managed Ethernet switch
designed for rolling stock, vehicle, and railway applications. The switch
boasts EN50155 compliance and M12 connectors to ensure tight and robust
connections in harsh environments where vibration and shock will cause
disturbances. With eight 10/100Base-T(X) P.S.E. ports, the switch can
provide power for IEEE 802.3af-compliant devices over an Ethernet cable
without using additional power. The device also provides two Gigabit fiber
ports in Q-ODC connector for long-distance connections. With complete
support for Ethernet redundancy protocols such as O-Ring (recovery time <
10ms over 250 units of connection), Open-Ring and MSTP/RSTP/STP (IEEE
802.1s/w/D), the switch can protect your mission-critical applications from
network interruptions or temporary malfunctions. Featuring a wide operating
o
o
temperature from -40 C to 70 C, the switch can be managed centrally via
Open-Vision, web browsers, Telnet and console (CLI) configuration.
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Contents
Pictures
TPS-3082GF-MM-M12-QODC
CD
QIG
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow:
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading:
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
TPS-3082GF-MM-M12-QODC
TPS-3082GF-MM-M12-QODC
G
uide
Dimension
Panel Layouts
Front View
Number
Tx+
Rx+
Tx+: PoE Vout+
Tx- : PoE Vout+
Rx+: PoE Vout-
Rx- : PoE Vout-
Rx-
Tx-
1
TPS-3082GF-M12
1
2
3
4 5
6
Relay
N.C.
3A@24VDC
1
RXD
TXD
7
N.C.
N.C.
GND
RS-232, 9600bps, 8, N, 1
10
V1+
V2+
1
8
V1-
V2-
9
11
12
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1:
Hold the
d
evice upright against the wall
Step 2:
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Step 3:
Slide the
d
evice downwards and tighten the four screws for added stability.
1907-2-29-TPS3082GFM12QODC-1.0
Tx+
Rx+
Tx+: PoE Vout+
Tx- : PoE Vout+
Rx+: PoE Vout-
Rx- : PoE Vout-
Rx-
Tx-
TPS-3082GF-M12
Relay
N.C.
3A@24VDC
RXD
TXD
N.C.
N.C.
GND
RS-232, 9600bps, 8, N, 1
V1+
V2+
V1-
V2-
1. Reset button
2. Power module indicators
3. R.M. status LED
4. Ring status LED
5. Fault LED
6. Relay output port
7. Console port
8. Power connector
9. PoE fast Ethernet ports
13
10. LNK/ACT indicator for PoE Fast Ethernet
14
port
11. PoE status LED for PoE Ethernet ports
12. Duplex/collision indicator for
PoE Ethernet port
13. Gigabit fiber ports
14. LNK/ACT indicator for gigabit fiber port
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
PRINTED ON RECYCLED PAPER
EN50155 10-port managed
PoE Ethernet switch
Wiring
For pin assignments of power, console and relay output ports, please refer to the following tables.
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Step 1:
Insert a power cable to the power connector on the device.
Step 2:
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Console port pinouts
RXD
TXD
N.C.
N.C.
GND
RS-232, 9600bps, 8, N, 1
Relay output port pinouts
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a cable with an M12
A-coded 5-pin male connector to connect the relay. The
relay contacts will detect user-configured events and form
an open circuit when an event is triggered.
Network Connection
The switch has eight 10/100Base-T(X) and two Gigabit fiber ports in the form of M12 connector.
Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network
devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable
Cable
Type
Max. Length
Connector
4-pin female M12
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
D-coding connector
4-pin female M12
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
D-coding connector
4-Pin PoE Port Definition
For pin assignments of the LAN ports, please refer to the following tables.
1
2
Pin No.
Description
Tx+
Rx+
#1
TD+ with PoE Vout +
#2
RD+ with PoE Vout -
Rx-
Tx-
4
3
#3
TD- with PoE Vout +
#4
RD- with PoE Vout -
Gigabit Fiber Port
* Notice: Please connect the cable in correct polarity
Quick Installation Guide
Version 1.0
V1+
V2+
V1-
V2-
Relay
N.C.
3A@24VDC
Need help?
Do you have a question about the TPS-3082GF-MM-M12-QODC and is the answer not in the manual?
Questions and answers